1 files changed, 112 insertions, 0 deletions
diff --git a/roms/u-boot/board/esd/dp405/dp405.c b/roms/u-boot/board/esd/dp405/dp405.c
new file mode 100644
index 00000000..730ff215
--- /dev/null
+++ b/roms/u-boot/board/esd/dp405/dp405.c
@@ -0,0 +1,112 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <command.h>
+#include <malloc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(UIC0ER, 0x00000000);       /* disable all ints */
+	mtdcr(UIC0CR, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(UIC0PR, 0xFFFFFF80);       /* set int polarities */
+	mtdcr(UIC0TR, 0x10000000);       /* set int trigger levels */
+	mtdcr(UIC0VCR, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(UIC0SR, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
+
+	/*
+	 * Reset CPLD via GPIO13 (CS4) pin
+	 */
+	out_be32((void *)GPIO0_OR,
+		 in_be32((void *)GPIO0_OR) & ~(0x80000000 >> 13));
+	udelay(1000); /* wait 1ms */
+	out_be32((void *)GPIO0_OR,
+		 in_be32((void *)GPIO0_OR) | (0x80000000 >> 13));
+	udelay(1000); /* wait 1ms */
+
+	return 0;
+}
+
+int misc_init_r (void)
+{
+	/* adjust flash start and offset */
+	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+	gd->bd->bi_flashoffset = 0;
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	char str[64];
+	int i = getenv_f("serial#", str, sizeof(str));
+	unsigned char trans[16] = {0x0,0x8,0x4,0xc,0x2,0xa,0x6,0xe,
+				   0x1,0x9,0x5,0xd,0x3,0xb,0x7,0xf};
+	unsigned char id1, id2, rev;
+
+	puts ("Board: ");
+
+	if (i == -1)
+		puts ("### No HW ID - assuming DP405");
+	else
+		puts(str);
+
+	id1 = trans[(~(in_be32((void *)GPIO0_IR) >> 5)) & 0x0000000f];
+	id2 = trans[(~(in_be32((void *)GPIO0_IR) >> 9)) & 0x0000000f];
+
+	rev = in_8((void *)0xf0001000);
+	if (rev & 0x10) /* old DP405 compatibility */
+		rev = in_8((void *)0xf0000800);
+
+	switch (rev & 0xc0) {
+	case 0x00:
+		puts(" (HW=DP405");
+		break;
+	case 0x80:
+		puts(" (HW=DP405/CO");
+		break;
+	case 0xc0:
+		puts(" (HW=DN405");
+		break;
+	}
+	printf(", ID=0x%1X%1X, PLD=0x%02X", id2, id1, rev & 0x0f);
+
+	if ((rev & 0xc0) == 0xc0) {
+		printf(", C5V=%s",
+		       in_be32((void *)GPIO0_IR) & 0x40000000 ? "off" : "on");
+	}
+	puts(")\n");
+
+	return 0;
+}