aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/patches-5.15/731-net-phy-mediatek-ge-soc-initialize-MT7988-PHY-LEDs-d.patch
blob: 83d0f26bf41824bd037c68e96edcfa64e7cb25e1 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
From 5d2d78860f98eb5c03bc404eb024606878901ac8 Mon Sep 17 00:00:00 2001
From: Daniel Golle <daniel@makrotopia.org>
Date: Tue, 13 Jun 2023 03:27:14 +0100
Subject: [PATCH] net: phy: mediatek-ge-soc: initialize MT7988 PHY LEDs default
 state

Initialize LEDs and set sane default values.
Read boottrap register and apply LED polarities accordingly to get
uniform behavior from all LEDs on MT7988.
Requires syscon phandle 'mediatek,pio' present in parenting MDIO bus
which should point to the syscon holding the boottrap register.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
 drivers/net/phy/mediatek-ge-soc.c | 144 ++++++++++++++++++++++++++++--
 1 file changed, 136 insertions(+), 8 deletions(-)

--- a/drivers/net/phy/mediatek-ge-soc.c
+++ b/drivers/net/phy/mediatek-ge-soc.c
@@ -1,11 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0+
 #include <linux/bitfield.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/nvmem-consumer.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/phy.h>
+#include <linux/regmap.h>
 
 #define MTK_GPHY_ID_MT7981			0x03a29461
 #define MTK_GPHY_ID_MT7988			0x03a29481
@@ -208,9 +210,40 @@
 #define MTK_PHY_DA_TX_R50_PAIR_C		0x53f
 #define MTK_PHY_DA_TX_R50_PAIR_D		0x540
 
+/* Registers on MDIO_MMD_VEND2 */
+#define MTK_PHY_LED0_ON_CTRL			0x24
+#define MTK_PHY_LED1_ON_CTRL			0x26
+#define   MTK_PHY_LED_ON_MASK			GENMASK(6, 0)
+#define   MTK_PHY_LED_ON_LINK1000		BIT(0)
+#define   MTK_PHY_LED_ON_LINK100		BIT(1)
+#define   MTK_PHY_LED_ON_LINK10			BIT(2)
+#define   MTK_PHY_LED_ON_LINKDOWN		BIT(3)
+#define   MTK_PHY_LED_ON_FDX			BIT(4) /* Full duplex */
+#define   MTK_PHY_LED_ON_HDX			BIT(5) /* Half duplex */
+#define   MTK_PHY_LED_FORCE_ON			BIT(6)
+#define   MTK_PHY_LED_POLARITY			BIT(14)
+#define   MTK_PHY_LED_ENABLE			BIT(15)
+
+#define MTK_PHY_LED0_BLINK_CTRL			0x25
+#define MTK_PHY_LED1_BLINK_CTRL			0x27
+#define   MTK_PHY_LED_1000TX			BIT(0)
+#define   MTK_PHY_LED_1000RX			BIT(1)
+#define   MTK_PHY_LED_100TX			BIT(2)
+#define   MTK_PHY_LED_100RX			BIT(3)
+#define   MTK_PHY_LED_10TX			BIT(4)
+#define   MTK_PHY_LED_10RX			BIT(5)
+#define   MTK_PHY_LED_COLLISION			BIT(6)
+#define   MTK_PHY_LED_RX_CRC_ERR		BIT(7)
+#define   MTK_PHY_LED_RX_IDLE_ERR		BIT(8)
+#define   MTK_PHY_LED_FORCE_BLINK		BIT(9)
+
 #define MTK_PHY_RG_BG_RASEL			0x115
 #define   MTK_PHY_RG_BG_RASEL_MASK		GENMASK(2, 0)
 
+/* Register in boottrap syscon defining the initial state of the 4 PHY LEDs */
+#define RG_GPIO_MISC_TPBANK0			0x6f0
+#define   RG_GPIO_MISC_TPBANK0_BOOTMODE		GENMASK(11, 8)
+
 /* These macro privides efuse parsing for internal phy. */
 #define EFS_DA_TX_I2MPB_A(x)			(((x) >> 0) & GENMASK(5, 0))
 #define EFS_DA_TX_I2MPB_B(x)			(((x) >> 6) & GENMASK(5, 0))
@@ -238,13 +271,6 @@ enum {
 	PAIR_D,
 };
 
-enum {
-	GPHY_PORT0,
-	GPHY_PORT1,
-	GPHY_PORT2,
-	GPHY_PORT3,
-};
-
 enum calibration_mode {
 	EFUSE_K,
 	SW_K
@@ -263,6 +289,10 @@ enum CAL_MODE {
 	SW_M
 };
 
+struct mtk_socphy_shared {
+	u32			boottrap;
+};
+
 static int mtk_socphy_read_page(struct phy_device *phydev)
 {
 	return __phy_read(phydev, MTK_EXT_PAGE_ACCESS);
@@ -1073,6 +1103,104 @@ static int mt798x_phy_config_init(struct
 	return mt798x_phy_calibration(phydev);
 }
 
+static int mt798x_phy_setup_led(struct phy_device *phydev, bool inverted)
+{
+	struct pinctrl *pinctrl;
+	const u16 led_on_ctrl_defaults = MTK_PHY_LED_ENABLE      |
+					 MTK_PHY_LED_ON_LINK1000 |
+					 MTK_PHY_LED_ON_LINK100  |
+					 MTK_PHY_LED_ON_LINK10;
+	const u16 led_blink_defaults = MTK_PHY_LED_1000TX |
+				       MTK_PHY_LED_1000RX |
+				       MTK_PHY_LED_100TX  |
+				       MTK_PHY_LED_100RX  |
+				       MTK_PHY_LED_10TX   |
+				       MTK_PHY_LED_10RX;
+
+	phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL,
+		      led_on_ctrl_defaults ^
+		      (inverted ? MTK_PHY_LED_POLARITY : 0));
+
+	phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL,
+		      led_on_ctrl_defaults);
+
+	phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_BLINK_CTRL,
+		      led_blink_defaults);
+
+	phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_BLINK_CTRL,
+		      led_blink_defaults);
+
+	pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led");
+	if (IS_ERR(pinctrl))
+		dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED\n");
+
+	return 0;
+}
+
+static int mt7988_phy_probe_shared(struct phy_device *phydev)
+{
+	struct device_node *np = dev_of_node(&phydev->mdio.bus->dev);
+	struct mtk_socphy_shared *priv = phydev->shared->priv;
+	struct regmap *regmap;
+	u32 reg;
+	int ret;
+
+	/* The LED0 of the 4 PHYs in MT7988 are wired to SoC pins LED_A, LED_B,
+	 * LED_C and LED_D respectively. At the same time those pins are used to
+	 * bootstrap configuration of the reference clock source (LED_A),
+	 * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D).
+	 * In practise this is done using a LED and a resistor pulling the pin
+	 * either to GND or to VIO.
+	 * The detected value at boot time is accessible at run-time using the
+	 * TPBANK0 register located in the gpio base of the pinctrl, in order
+	 * to read it here it needs to be referenced by a phandle called
+	 * 'mediatek,pio' in the MDIO bus hosting the PHY.
+	 * The 4 bits in TPBANK0 are kept as package shared data and are used to
+	 * set LED polarity for each of the LED0.
+	 */
+	regmap = syscon_regmap_lookup_by_phandle(np, "mediatek,pio");
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = regmap_read(regmap, RG_GPIO_MISC_TPBANK0, &reg);
+	if (ret)
+		return ret;
+
+	priv->boottrap = FIELD_GET(RG_GPIO_MISC_TPBANK0_BOOTMODE, reg);
+
+	return 0;
+}
+
+static bool mt7988_phy_get_boottrap_polarity(struct phy_device *phydev)
+{
+	struct mtk_socphy_shared *priv = phydev->shared->priv;
+
+	if (priv->boottrap & BIT(phydev->mdio.addr))
+		return false;
+
+	return true;
+}
+
+static int mt7988_phy_probe(struct phy_device *phydev)
+{
+	int err;
+
+	err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0,
+				    sizeof(struct mtk_socphy_shared));
+	if (err)
+		return err;
+
+	if (phy_package_probe_once(phydev)) {
+		err = mt7988_phy_probe_shared(phydev);
+		if (err)
+			return err;
+	}
+
+	mt798x_phy_setup_led(phydev, mt7988_phy_get_boottrap_polarity(phydev));
+
+	return mt798x_phy_calibration(phydev);
+}
+
 static struct phy_driver mtk_socphy_driver[] = {
 	{
 		PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981),
@@ -1092,7 +1220,7 @@ static struct phy_driver mtk_socphy_driv
 		.config_init	= mt798x_phy_config_init,
 		.config_intr	= genphy_no_config_intr,
 		.handle_interrupt = genphy_handle_interrupt_no_ack,
-		.probe		= mt798x_phy_calibration,
+		.probe		= mt7988_phy_probe,
 		.suspend	= genphy_suspend,
 		.resume		= genphy_resume,
 		.read_page	= mtk_socphy_read_page,