aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/layerscape/patches-5.4/802-can-0022-can-flexcan-add-Transceiver-Delay-Compensation-suopp.patch
blob: 0b3a1bc9b6344fcf8d5a500b7ae355795bb05035 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
From 7b294e0cd2f7fbfb548a17b8d68d161da19e6592 Mon Sep 17 00:00:00 2001
From: Joakim Zhang <qiangqing.zhang@nxp.com>
Date: Fri, 12 Jul 2019 08:02:56 +0000
Subject: [PATCH] can: flexcan: add Transceiver Delay Compensation suopport

The CAN FD protocol allows the transmission and reception of data at a higher
bit rate than the nominal rate used in the arbitration phase when the message's
BRS bit is set.

The TDC mechanism is effective only during the data phase of FD frames
having BRS bit set. It has no effect either on non-FD frames, or on FD
frames transmitted at normal bit rate.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
 drivers/net/can/flexcan.c | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)

--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -149,8 +149,11 @@
 
 /* FLEXCAN FD control register (FDCTRL) bits */
 #define FLEXCAN_FDCTRL_FDRATE		BIT(31)
+#define FLEXCAN_FDCTRL_TDCEN		BIT(15)
+#define FLEXCAN_FDCTRL_TDCFAIL		BIT(14)
 #define FLEXCAN_FDCTRL_MBDSR1(x)	(((x) & 0x3) << 19)
 #define FLEXCAN_FDCTRL_MBDSR0(x)	(((x) & 0x3) << 16)
+#define FLEXCAN_FDCTRL_TDCOFF(x)	(((x) & 0x1f) << 8)
 
 /* FLEXCAN FD Bit Timing register (FDCBT) bits */
 #define FLEXCAN_FDCBT_FPRESDIV(x)	(((x) & 0x3ff) << 20)
@@ -1102,7 +1105,7 @@ static void flexcan_set_bittiming(struct
 	struct can_bittiming *bt = &priv->can.bittiming;
 	struct can_bittiming *dbt = &priv->can.data_bittiming;
 	struct flexcan_regs __iomem *regs = priv->regs;
-	u32 reg, reg_cbt, reg_fdcbt;
+	u32 reg, reg_cbt, reg_fdcbt, reg_fdctrl;
 
 	reg = priv->read(&regs->ctrl);
 	reg &= ~(FLEXCAN_CTRL_LPB | FLEXCAN_CTRL_SMP | FLEXCAN_CTRL_LOM);
@@ -1174,6 +1177,19 @@ static void flexcan_set_bittiming(struct
 					FLEXCAN_FDCBT_FPROPSEG(dbt->prop_seg);
 			priv->write(reg_fdcbt, &regs->fdcbt);
 
+			/* enable transceiver delay compensation(TDC) for fd frame.
+			 * TDC must be disabled when Loop Back mode is enabled.
+			 */
+			reg_fdctrl = priv->read(&regs->fdctrl);
+			if (!(reg & FLEXCAN_CTRL_LPB)) {
+				reg_fdctrl |= FLEXCAN_FDCTRL_TDCEN;
+				reg_fdctrl &= ~FLEXCAN_FDCTRL_TDCOFF(0x1f);
+				/* for the TDC to work reliably, the offset has to use optimal settings */
+				reg_fdctrl |= FLEXCAN_FDCTRL_TDCOFF(((dbt->phase_seg1 - 1) + dbt->prop_seg + 2) *
+								    ((dbt->brp -1) + 1));
+			}
+			priv->write(reg_fdctrl, &regs->fdctrl);
+
 			if (bt->brp != dbt->brp)
 				netdev_warn(dev, "Warning!! data brp = %d and brp = %d don't match.\n"
 					    "flexcan may not work. consider using different bitrate or data bitrate\n",
@@ -1323,6 +1339,7 @@ static int flexcan_chip_start(struct net
 	/* FDCTRL */
 	if (priv->can.ctrlmode_supported & CAN_CTRLMODE_FD) {
 		reg_fdctrl = priv->read(&regs->fdctrl) & ~FLEXCAN_FDCTRL_FDRATE;
+		reg_fdctrl &= ~FLEXCAN_FDCTRL_TDCEN;
 		reg_fdctrl &= ~(FLEXCAN_FDCTRL_MBDSR1(0x3) | FLEXCAN_FDCTRL_MBDSR0(0x3));
 		reg_mcr = priv->read(&regs->mcr) & ~FLEXCAN_MCR_FDEN;
 		reg_ctrl2 = priv->read(&regs->ctrl2) & ~FLEXCAN_CTRL2_ISOCANFDEN;