1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
|
From 11d6a6128a5a07c429941afc202b6e62a19771be Mon Sep 17 00:00:00 2001
From: John Thomson <git@johnthomson.fastmail.com.au>
Date: Fri, 23 Oct 2020 19:42:36 +1000
Subject: [PATCH 2/2] arm: compressed: set ipq40xx watchdog to allow boot
For IPQ40XX systems where the SoC watchdog is activated before linux,
the watchdog timer may be too small for linux to finish uncompress,
boot, and watchdog management start.
If the watchdog is enabled, set the timeout for it to 30 seconds.
The functionality and offsets were copied from:
drivers/watchdog/qcom-wdt.c qcom_wdt_set_timeout & qcom_wdt_start
The watchdog memory address was taken from:
arch/arm/boot/dts/qcom-ipq4019.dtsi
This was required on Mikrotik IPQ40XX consumer hardware using Mikrotik's
RouterBoot bootloader.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
---
arch/arm/boot/compressed/head.S | 35 +++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -602,6 +602,41 @@ not_relocated: mov r0, #0
bic r4, r4, #1
blne cache_on
+/* Set the Qualcom IPQ40xx watchdog timeout to 30 seconds
+ * if it is enabled, so that there is time for kernel
+ * to decompress, boot, and take over the watchdog.
+ * data and functionality from drivers/watchdog/qcom-wdt.c
+ * address from arch/arm/boot/dts/qcom-ipq4019.dtsi
+ */
+#ifdef CONFIG_ARCH_IPQ40XX
+watchdog_set:
+ /* offsets:
+ * 0x04 reset (=1 resets countdown)
+ * 0x08 enable (=0 disables)
+ * 0x0c status (=1 when SoC was reset by watchdog)
+ * 0x10 bark (=timeout warning in ticks)
+ * 0x14 bite (=timeout reset in ticks)
+ * clock rate is 1<<15 hertz
+ */
+ .equ watchdog, 0x0b017000 @Store watchdog base address
+ movw r0, #:lower16:watchdog
+ movt r0, #:upper16:watchdog
+ ldr r1, [r0, #0x08] @Get enabled?
+ cmp r1, #1 @If not enabled, do not change
+ bne watchdog_finished
+ mov r1, #0
+ str r1, [r0, #0x08] @Disable the watchdog
+ mov r1, #1
+ str r1, [r0, #0x04] @Pet the watchdog
+ mov r1, #30 @30 seconds timeout
+ lsl r1, r1, #15 @converted to ticks
+ str r1, [r0, #0x10] @Set the bark timeout
+ str r1, [r0, #0x14] @Set the bite timeout
+ mov r1, #1
+ str r1, [r0, #0x08] @Enable the watchdog
+watchdog_finished:
+#endif /* CONFIG_ARCH_IPQ40XX */
+
/*
* The C runtime environment should now be setup sufficiently.
* Set up some pointers, and start decompressing.
|
