target/linux/ath79/dts/qca955x_zyxel_nbg6x16.dtsi


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "qca955x.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	keys: keys {
		compatible = "gpio-keys";

		wifi {
			label = "WiFi on/off button";
			linux,code = <KEY_RFKILL>;
			linux,input-type = <EV_SW>;
			gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
			debounce-interval = <60>;
		};

		wps {
			label = "WPS button";
			linux,code = <KEY_WPS_BUTTON>;
			gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};

		reset {
			label = "Reset button";
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};
	};
};

&gpio {
	gpio_usb_power: usb_power {
		gpio-hog;
		gpios = <16 0>;
		output-high;
	};
};

&uart {
	status = "okay";
};

&mdio0 {
	status = "okay";

	phy17: ethernet-phy@11 {
		reg = <0x11>;
		phy-mode = "rgmii-id";
	};

	switch0@1f {
		compatible = "qca,ar8327";
		reg = <0x1f>;
		qca,ar8327-initvals = <
			0x04 0x87600000 /* PORT0 PAD MODE CTRL */
			0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
			0x10 0x81000080 /* POWER_ON_STRAP */
			0x50 0xffb7ffb7 /* LED_CTRL0 */
			0x54 0xffb7ffb7 /* LED_CTRL1 */
			0x58 0xffb7ffb7 /* LED_CTRL2 */
			0x5c 0x03ffff00 /* LED_CTRL3 */
			0x7c 0x0000007e /* PORT0_STATUS */
			0x94 0x0000007e /* PORT6 STATUS */
			>;
	};
};

&mdio1 {
	status = "okay";

	phy1: ethernet-phy@1 {
		reg = <1>;
		phy-mode = "sgmii";
	};
};


&eth0 {
	status = "okay";

	pll-data = <0xa6000000 0x00000101 0x00001616>;
	phy-handle = <&phy17>;

	fixed-link {
		speed = <1000>;
		full-duplex;
	};
};

&eth1 {
	status = "okay";

	pll-data = <0x03000101 0x00000101 0x00001616>;
	phy-handle = <&phy1>;

	fixed-link {
		speed = <1000>;
		full-duplex;
	};
};

&wmac {
	status = "okay";

	mtd-cal-data = <&art 0x1000>;
};

&usb_phy0 {
	status = "okay";
};

&usb_phy1 {
	status = "okay";
};

&usb0 {
	status = "okay";

	hub_port0: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};

};

&usb1 {
	status = "okay";

	hub_port1: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};
};