target/linux/ath79/dts/ar9331_etactica_eg200.dts


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9331.dtsi"

/ {
	model = "eTactica EG200";
	compatible = "etactica,eg200", "qca,ar9331";

	aliases {
		serial0 = &uart;
	};

	keys {
		compatible = "gpio-keys-polled";
		poll-interval = <50>;

		restore {
			linux,code = <KEY_WPS_BUTTON>;
			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
		};
	};

	leds {
		compatible = "gpio-leds";

		modbus {
			label = "eg200:red:modbus";
			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
		};

		etactica {
			label = "eg200:red:etactica";
			gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
		};

		eth0 {
			label = "eg200:red:eth0";
			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
		};

		wlan {
			label = "eg200:red:wlan";
			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "phy0tpt";
		};
	};
};

&uart {
	status = "okay";
};

&gpio {
	status = "okay";
};

&usb {
	dr_mode = "host";
	status = "okay";
};

&usb_phy {
	status = "okay";
};

&eth0 {
	status = "okay";
	mtd-mac-address = <&art 0x0>;

	gmac-config {
		device = <&gmac>;
		switch-phy-addr-swap = <1>;
		switch-phy-swap = <1>;
	};
};

&eth1 {
	status = "okay";
	compatible = "syscon", "simple-mfd";
};

&spi {
	num-chipselects = <1>;
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			uboot@0 {
				reg = <0x0 0x40000>;
				read-only;
			};

			uboot-env@40000 {
				reg = <0x40000 0x10000>;
				read-only;
			};

			firmware@50000 {
				compatible = "denx,uimage";
				reg = <0x50000 0xfa0000>;
			};

			art: art@ff0000 {
				reg = <0xff0000 0x10000>;
				read-only;
			};
		};
	};
};

&wmac {
	status = "okay";
	mtd-cal-data = <&art 0x1000>;
	mtd-mac-address = <&art 0x1002>;
};