1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
|
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -655,6 +655,9 @@
* When a security association was established on an 802.1X network using
* fast transition, this event should be followed by an
* %NL80211_CMD_PORT_AUTHORIZED event.
+ * Following a %NL80211_CMD_ROAM event userspace can issue
+ * %NL80211_CMD_GET_SCAN in order to obtain the scan information for the
+ * new BSS the card/driver roamed to.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
* userspace that a connection was dropped by the AP or due to other
* reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
@@ -757,7 +760,8 @@
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
- * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface
+ * (no longer supported).
*
* @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
* multicast to unicast conversion. When enabled, all multicast packets
@@ -1177,6 +1181,10 @@
* includes the contents of the frame. %NL80211_ATTR_ACK flag is included
* if the recipient acknowledged the frame.
*
+ * @NL80211_CMD_SET_SAR_SPECS: SAR power limitation configuration is
+ * passed using %NL80211_ATTR_SAR_SPEC. %NL80211_ATTR_WIPHY is used to
+ * specify the wiphy index to be applied to.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
@@ -1407,6 +1415,8 @@ enum nl80211_commands {
NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
+ NL80211_CMD_SET_SAR_SPECS,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
@@ -1750,8 +1760,9 @@ enum nl80211_commands {
* specify just a single bitrate, which is to be used for the beacon.
* The driver must also specify support for this with the extended
* features NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
- * NL80211_EXT_FEATURE_BEACON_RATE_HT and
- * NL80211_EXT_FEATURE_BEACON_RATE_VHT.
+ * NL80211_EXT_FEATURE_BEACON_RATE_HT,
+ * NL80211_EXT_FEATURE_BEACON_RATE_VHT and
+ * NL80211_EXT_FEATURE_BEACON_RATE_HE.
*
* @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
* at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
@@ -1955,8 +1966,15 @@ enum nl80211_commands {
* @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
* probe-response frame. The DA field in the 802.11 header is zero-ed out,
* to be filled by the FW.
- * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
- * this feature. Currently, only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_VHT: Force VHT capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
+ * @NL80211_ATTR_DISABLE_HE: Force HE capable interfaces to disable
+ * this feature during association. This is a flag attribute.
+ * Currently only supported in mac80211 drivers.
* @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
* ATTR_HT_CAPABILITY to which attention should be paid.
* Currently, only mac80211 NICs support this feature.
@@ -2077,7 +2095,8 @@ enum nl80211_commands {
* until the channel switch event.
* @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
* must be blocked on the current channel (before the channel switch
- * operation).
+ * operation). Also included in the channel switch started event if quiet
+ * was requested by the AP.
* @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
* for the time while performing a channel switch.
* @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel
@@ -2527,6 +2546,20 @@ enum nl80211_commands {
* override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
* NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
*
+ * @NL80211_ATTR_SAE_PWE: Indicates the mechanism(s) allowed for SAE PWE
+ * derivation in WPA3-Personal networks which are using SAE authentication.
+ * This is a u8 attribute that encapsulates one of the values from
+ * &enum nl80211_sae_pwe_mechanism.
+ *
+ * @NL80211_ATTR_SAR_SPEC: SAR power limitation specification when
+ * used with %NL80211_CMD_SET_SAR_SPECS. The message contains fields
+ * of %nl80211_sar_attrs which specifies the sar type and related
+ * sar specs. Sar specs contains array of %nl80211_sar_specs_attrs.
+ *
+ * @NL80211_ATTR_RECONNECT_REQUESTED: flag attribute, used with deauth and
+ * disassoc events to indicate that an immediate reconnect to the AP
+ * is desired.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -3016,6 +3049,14 @@ enum nl80211_attrs {
NL80211_ATTR_S1G_CAPABILITY,
NL80211_ATTR_S1G_CAPABILITY_MASK,
+ NL80211_ATTR_SAE_PWE,
+
+ NL80211_ATTR_RECONNECT_REQUESTED,
+
+ NL80211_ATTR_SAR_SPEC,
+
+ NL80211_ATTR_DISABLE_HE,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -5896,6 +5937,19 @@ enum nl80211_feature_flags {
* @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports
* unsolicited broadcast probe response transmission
*
+ * @NL80211_EXT_FEATURE_BEACON_RATE_HE: Driver supports beacon rate
+ * configuration (AP/mesh) with HE rates.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_LTF: Device supports secure LTF measurement
+ * exchange protocol.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_RTT: Device supports secure RTT measurement
+ * exchange protocol.
+ *
+ * @NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE: Device supports management
+ * frame protection for all management frames exchanged during the
+ * negotiation and range measurement procedure.
+ *
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
@@ -5956,6 +6010,10 @@ enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_SAE_OFFLOAD_AP,
NL80211_EXT_FEATURE_FILS_DISCOVERY,
NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP,
+ NL80211_EXT_FEATURE_BEACON_RATE_HE,
+ NL80211_EXT_FEATURE_SECURE_LTF,
+ NL80211_EXT_FEATURE_SECURE_RTT,
+ NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
@@ -6253,11 +6311,13 @@ struct nl80211_vendor_cmd_info {
* @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
* @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
* @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
+ * @NL80211_TDLS_PEER_HE: TDLS peer is HE capable.
*/
enum nl80211_tdls_peer_capability {
NL80211_TDLS_PEER_HT = 1<<0,
NL80211_TDLS_PEER_VHT = 1<<1,
NL80211_TDLS_PEER_WMM = 1<<2,
+ NL80211_TDLS_PEER_HE = 1<<3,
};
/**
@@ -6849,6 +6909,9 @@ enum nl80211_peer_measurement_ftm_capa {
* if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
* %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
* ranging will be used.
+ * @NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK: negotiate for LMR feedback. Only
+ * valid if either %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED or
+ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set.
*
* @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
* @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
@@ -6867,6 +6930,7 @@ enum nl80211_peer_measurement_ftm_req {
NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
+ NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK,
/* keep last */
NUM_NL80211_PMSR_FTM_REQ_ATTR,
@@ -7124,4 +7188,115 @@ enum nl80211_unsol_bcast_probe_resp_attr
NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX =
__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1
};
+
+/**
+ * enum nl80211_sae_pwe_mechanism - The mechanism(s) allowed for SAE PWE
+ * derivation. Applicable only when WPA3-Personal SAE authentication is
+ * used.
+ *
+ * @NL80211_SAE_PWE_UNSPECIFIED: not specified, used internally to indicate that
+ * attribute is not present from userspace.
+ * @NL80211_SAE_PWE_HUNT_AND_PECK: hunting-and-pecking loop only
+ * @NL80211_SAE_PWE_HASH_TO_ELEMENT: hash-to-element only
+ * @NL80211_SAE_PWE_BOTH: both hunting-and-pecking loop and hash-to-element
+ * can be used.
+ */
+enum nl80211_sae_pwe_mechanism {
+ NL80211_SAE_PWE_UNSPECIFIED,
+ NL80211_SAE_PWE_HUNT_AND_PECK,
+ NL80211_SAE_PWE_HASH_TO_ELEMENT,
+ NL80211_SAE_PWE_BOTH,
+};
+
+/**
+ * enum nl80211_sar_type - type of SAR specs
+ *
+ * @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit
+ *
+ */
+enum nl80211_sar_type {
+ NL80211_SAR_TYPE_POWER,
+
+ /* add new type here */
+
+ /* Keep last */
+ NUM_NL80211_SAR_TYPE,
+};
+
+/**
+ * enum nl80211_sar_attrs - Attributes for SAR spec
+ *
+ * @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type.
+ *
+ * @NL80211_SAR_ATTR_SPECS: Nested array of SAR power
+ * limit specifications. Each specification contains a set
+ * of %nl80211_sar_specs_attrs.
+ *
+ * For SET operation, it contains array of %NL80211_SAR_ATTR_SPECS_POWER
+ * and %NL80211_SAR_ATTR_SPECS_RANGE_INDEX.
+ *
+ * For sar_capa dump, it contains array of
+ * %NL80211_SAR_ATTR_SPECS_START_FREQ
+ * and %NL80211_SAR_ATTR_SPECS_END_FREQ.
+ *
+ * @__NL80211_SAR_ATTR_LAST: Internal
+ * @NL80211_SAR_ATTR_MAX: highest sar attribute
+ *
+ * These attributes are used with %NL80211_CMD_SET_SAR_SPEC
+ */
+enum nl80211_sar_attrs {
+ __NL80211_SAR_ATTR_INVALID,
+
+ NL80211_SAR_ATTR_TYPE,
+ NL80211_SAR_ATTR_SPECS,
+
+ __NL80211_SAR_ATTR_LAST,
+ NL80211_SAR_ATTR_MAX = __NL80211_SAR_ATTR_LAST - 1,
+};
+
+/**
+ * enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs
+ *
+ * @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual
+ * power limit value in units of 0.25 dBm if type is
+ * NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm).
+ * 0 means userspace doesn't have SAR limitation on this associated range.
+ *
+ * @NL80211_SAR_ATTR_SPECS_RANGE_INDEX: Required (u32) value to specify the
+ * index of exported freq range table and the associated power limitation
+ * is applied to this range.
+ *
+ * Userspace isn't required to set all the ranges advertised by WLAN driver,
+ * and userspace can skip some certain ranges. These skipped ranges don't
+ * have SAR limitations, and they are same as setting the
+ * %NL80211_SAR_ATTR_SPECS_POWER to any unreasonable high value because any
+ * value higher than regulatory allowed value just means SAR power
+ * limitation is removed, but it's required to set at least one range.
+ * It's not allowed to set duplicated range in one SET operation.
+ *
+ * Every SET operation overwrites previous SET operation.
+ *
+ * @NL80211_SAR_ATTR_SPECS_START_FREQ: Required (u32) value to specify the start
+ * frequency of this range edge when registering SAR capability to wiphy.
+ * It's not a channel center frequency. The unit is kHz.
+ *
+ * @NL80211_SAR_ATTR_SPECS_END_FREQ: Required (u32) value to specify the end
+ * frequency of this range edge when registering SAR capability to wiphy.
+ * It's not a channel center frequency. The unit is kHz.
+ *
+ * @__NL80211_SAR_ATTR_SPECS_LAST: Internal
+ * @NL80211_SAR_ATTR_SPECS_MAX: highest sar specs attribute
+ */
+enum nl80211_sar_specs_attrs {
+ __NL80211_SAR_ATTR_SPECS_INVALID,
+
+ NL80211_SAR_ATTR_SPECS_POWER,
+ NL80211_SAR_ATTR_SPECS_RANGE_INDEX,
+ NL80211_SAR_ATTR_SPECS_START_FREQ,
+ NL80211_SAR_ATTR_SPECS_END_FREQ,
+
+ __NL80211_SAR_ATTR_SPECS_LAST,
+ NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
+};
+
#endif /* __LINUX_NL80211_H */
|
