aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix typo in rb91x nand sourceKoen Vandeputte2018-08-241-1/+2
| | | | | | Fixes: 3b1ea0996f83 ("ar71xx: fix build error due to bad include") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: ubnt-xm: create mapping for RSSI LEDsLech Perczak2018-08-231-0/+7
| | | | | | | | | | Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI mapping for them, so visual feedback on RSSI is available, when using userspace RSSI monitor daemon. Runtime tested using rssileds. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: hijack LED4 as booting/failsafeLech Perczak2018-08-231-1/+6
| | | | | | | | | | Create aliases for led-booting and led-failsafe pointing at ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback on device status becomes available, in order to enter failsafe mode via button. led-running and led-upgrade aliases are omitted to avoid conflicting with RSSI LEDs when in normal operation. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: disable WAN on (rocket|bullet)-mLech Perczak2018-08-231-0/+2
| | | | | | | | | | | ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet port, therefore disable creation of WAN zone and interfaces for them, as their intended purpose is a wireless bridge. This aligns the configuration with one found in ar71xx target. ubnt,nano-m target is kept as is, being a two-port device. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: support ath9k firmware loadingLech Perczak2018-08-231-0/+5
| | | | | | | | Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards. This is required for wireless interface to function. Runtime tested on Nanobridge M5. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for I-O DATA ETG3-RINAGAKI Hiroshi2018-08-233-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA ETG3-R is a wired router, based on Atheros AR9342. Specification: - Atheros AR9342 - 64 MB of RAM - 8 MB of Flash - 5x 10/100/1000 Ethernet - AR8327N - 2x LEDs, 1x key - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using initramfs image: 1. Connect serial cable to UART header on ETG3-R 2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in the TFTP directory 3. Set IP address of the computer to 192.168.0.10, connect to the LAN port of ETG3-R, and start the TFTP server on the computer 4. Connect power cable to ETG3-R and turn on the router 5. Press "Enter" key when the "Hit any key to stop autoboot:" message is displayed on the console and enter the u-boot cli 6. execute following commands to change kernel address for u-boot setenv bootsf 1 setenv mtd_kernel1 "bootm 0x9f050000" saveenv 7. execute "tftpboot; bootm" command to download the initramfs image from TFTP server and boot with it 8. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for ETG3-R 9. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7620: add dir-810l network configRoger Pueyo Centelles2018-08-231-0/+1
| | | | | | | The device was not included in the /etc/board.d/02_network file, so the network wouldn't be properly set up on boot. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for ELECOM WRC-1900GSTNOGUCHI Hiroshi2018-08-236-172/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: fix compatibles in SoC dtsiMathias Kresin2018-08-233-3/+3
| | | | | | | The former used compatibles aren't defined anywhere and aren't used by the devicetree source files including them. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix GL-MT300N-V2 SoC compatibleMathias Kresin2018-08-231-1/+1
| | | | | | | | According to abbfcc85259a ("ramips: add support for GL-inet GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC compatible to match the used hardware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop not existing groups from pinmuxMathias Kresin2018-08-2310-10/+10
| | | | | | | | | | | | | | RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't have a jtag group. Having these groups defined might cause a boot panic. The pin controller fails to initialise for kernels > 4.9 if invalid groups are used. If a subsystem references a pin controller configuration node, it can not find this node and errors out. In worst case it's the SPI driver which errors out and we have no root filesystem to mount. Signed-off-by: Mathias Kresin <dev@kresin.me>
* generic: revert workarounds for AR8337 switchMathias Kresin2018-08-232-62/+1
| | | | | | | | | | | | | The intention of 967b6be118e3 ("ar8327: Add workarounds for AR8337 switch") was to remove the register fixups for AR8337. But instead they were removed for AR8327. The RGMII RX delay is forced even if the port is used as phy instead of mac, which results in no package flow at least for one board. Fixes: FS#1664 Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.66Koen Vandeputte2018-08-2246-368/+230
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.123Koen Vandeputte2018-08-223-17/+17
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix build error due to bad includeKoen Vandeputte2018-08-224-5/+20
| | | | | | | | | | | | | | | | | | While "rawnand.h" is available in kernel 4.14, the default for this target is kernel 4.9 in which "nand.h" should be used. Add an extra check to include the correct file depending on kernel version Fixes these build errors: drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory #include <linux/mtd/rawnand.h> ^~~~~~~~~~~~~~~~~~~~~ compilation terminated. Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add missing include for checking kernel versionKoen Vandeputte2018-08-2210-0/+10
| | | | | | | | | | | | | | | | | | Fixes these build errors: arch/mips/ath79/mach-rb2011.c:20:5: error: "LINUX_VERSION_CODE" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:26: error: "KERNEL_VERSION" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:40: error: missing binary operator before token "(" #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^ Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add v4.14 supportJohn Crispin2018-08-22164-78/+8268
| | | | | | adds v4.14 patches for testing but leaves v4.9 as default for now. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 3.18 to 3.18.119Koen Vandeputte2018-08-2045-196/+171
| | | | | | | | | Refreshed all patches. Compile-tested on: adm5120, adm8668, au1000, mcs814x, ppc40x, ppc44x, xburst Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.122Koen Vandeputte2018-08-203-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix TL-MR3020 image metadataDavid Bauer2018-08-191-1/+1
| | | | | | | | | | Sysupgrading to ath79 from ar71xx currently fails because of mismatching supported_devices. ar71xx is expecting "tl-mr3020" which is missing in the ath79 image. Upgrading from ath79 is unaffected, as the image contains the old string for ar71xx and the new one coming from the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: cleanup PISEN WMM003N image metadataChuanhong Guo2018-08-191-1/+0
| | | | | | | PISEN WMM003N is never supported by ar71xx, this commit also removed SUPPORTED_DEVICES for it because it's completely useless. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Fritz!Box 4020David Bauer2018-08-195-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs The USB port doesn't work. Both Root Hubs are detected as having 0 Ports: [ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.723267] usbcore: registered new interface driver usbfs [ 3.729058] usbcore: registered new interface driver hub [ 3.734616] usbcore: registered new device driver usb [ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.758357] SCSI subsystem initialized [ 3.766026] ehci-platform: EHCI generic platform driver [ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller [ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00 [ 3.824001] hub 1-0:1.0: USB hub found [ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller [ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00 [ 3.894011] hub 2-0:1.0: USB hub found [ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.908928] usbcore: registered new interface driver usb-storage [ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/* A few words about the shift-register: AVM used a trick to control the shift-register for the LEDs with only 2 pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple shift-registers, pulls the latch, moving the shift register-state to the storage register. It also pulls down MR (normally pulled up) to clear the storage register, so the latch gets released and will not be pulled by the remaining bits in the shift-register. Shift register is all-zero after this. For that we need to make sure output 7 is set to high on driver probe. We accomplish this by using gpio-hogging. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v1Christian Lamparter2018-08-193-0/+56
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 8 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!) - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c7-1750> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for I-O DATA WN-AC1167DGRINAGAKI Hiroshi2018-08-167-208/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz wifi - 2.4 GHz: SoC internal - 5 GHz: QCA988x - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1167DGR 2. Connect power cable to WN-AC1167DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix leds and network for TP-Link TL-WR841 v9/v11Johann Neuhauser2018-08-162-7/+5
| | | | | | | | | Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds and 02_network script files are missing in commits cc35c91 and 8db6522. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [merged with identical case in 02_network] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: don't use the pcs,cr5000 wps led as usb ledMathias Kresin2018-08-162-5/+1
| | | | | | | If it isn't a usb led, it shouldn't be used as one by default. It is up to the user to add such a (mis)configuration for the board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link MR-3040 v2Dmitry Tunin2018-08-164-1/+178
| | | | | | Add support for the ar71xx supported TP-Link MR-3040 v2. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add support for Buffalo WHR-G301NINAGAKI Hiroshi2018-08-165-4/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240. Ported from ar71xx target. Specification: - Atheros AR7240 - 32 MB of RAM - 4 MB of Flash - 2.4 GHz 2T2R wifi - 5x 10/100 Mbps Ethernet - 9x LEDs, 4x keys - LED: 8x gpio-leds, 1x ath9k-leds - key: 2x buttons, 1x slide switch - UART header on PCB - Vcc, GND, TX, RX from LEDs side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WHR-G301N 2. Connect power cable to WHR-G301N and turn on it 3. Access to "http://192.168.11.1/" and open firmware update page ("ファーム更新") 4. Select the OpenWrt factory image and click execute ("実行") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [fix the SUPPORTED_DEVICES to be compatible with the ar71xx image] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add support for upgrade ledMathias Kresin2018-08-1636-0/+44
| | | | | | | | | | Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh script en par with the other implementations using devicetree aliases to define multiple leds for boot status indication. By default, use the boot finished led to indicate an upgrade for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop unused get_status_led functionsMathias Kresin2018-08-162-8/+0
| | | | | | | The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix upgrade led handlingMathias Kresin2018-08-164-8/+16
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: consolidate upgrade state setMathias Kresin2018-08-164-23/+0
| | | | | | | | | | Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: fix bad indentMathias Kresin2018-08-161-7/+6
| | | | | | | Fix the indent to make the make it obvious which condition is the parent of the loop. Signed-off-by: Mathias Kresin <dev@kresin.me>
* cns3xxx: fix mtu setting with kernel 4.14Mathias Kresin2018-08-161-10/+1
| | | | | | | | | | | Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It's necessary to set a max_mtu if a mtu > 1500 is supported. Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump kernel 4.9 to version 4.9.120Hauke Mehrtens2018-08-151-65/+0
| | | | | | | | | | | The following patch was integrated upstream: * target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump kernel 4.14 to version 4.14.63Hauke Mehrtens2018-08-154-105/+4
| | | | | | | | | | | | The following patches were integrated upstream: * target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch * target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: use both WNDR3x00 power leds for boot status indicationDmitry Tunin2018-08-151-5/+5
| | | | | | | | | | | Use the orange led by default to match the bootloader/stock firmware behaviour. Turn on the green power led after boot to indicate a finished boot and the orange one off. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message, keep orange power led enabled during early kernel boot] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: use both DIR-825 B1 power leds for boot status indicationDmitry Tunin2018-08-151-2/+3
| | | | | | | | | | | Use the orange led by default to match the bootloader/stock firmware behaviour. Turn on the blue power led after boot to indicate a finished boot and the orange one off. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message, keep orange power led enabled during early kernel boot] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for indicating the boot state using multiple ledsDmitry Tunin2018-08-1533-37/+157
| | | | | | | | | | | Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which supports different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DWR-118-A2Cezary Jackiewicz2018-08-157-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: enable all ports unconditionallyPawel Dembicki2018-08-151-1/+10
| | | | | | | This patch make all mt7620 ephy ports turned on. It is necessary for some JBOOT devices. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for HiWiFi HC5861Bold-masterDeng Qingfang2018-08-145-1/+155
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN https://www.hiwifi.com/enjoy-view Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7612EN 802.11ac 2T2R 867Mbps - 5x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Everything is working Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath79: add support for TP-Link TL-WR941N/ND v2/v3Chuanhong Guo2018-08-144-0/+184
| | | | | | | | | | | | | Specification: - SoC: Atheros AR9132 - Flash: 4 MB - RAM: 32 MB - Ethernet: Marvell 88E6060 with 5 FE ports. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for TP-Link WR841N/ND v11Johann Neuhauser2018-08-143-1/+42
| | | | | | | | | | | | | | Specification: - SoC: Atheros AR9533 - Flash: 4 MB - RAM: 32 MB - Ethernet: 4x LAN (100M) / 1x WAN (100M) - WiFi: 2.4G 300M Flash instruction: Flash factory image from stock WebUI. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: move TP-Link WR841v9 aliases node from dtsi to dtsJohann Neuhauser2018-08-142-5/+5
| | | | | | | | Move the alias node of the TP-Link WR841v9 and rename the phandle of the qss led to qss_led in preparation for adding the very similar TP-Link WR841v11. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix sysupgrade TP-Link WR841v9Johann Neuhauser2018-08-142-2/+1
| | | | | | | Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and for consistency rename everything to tl-wr841-v9. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800Hannu Nyman2018-08-144-1/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath9k wifi capabilities to WNDR3700 family. * use kmod-owl-loader to load firmware from "art" * add wifi to DTS * add wifi LEDs Avoid using the same MAC for eth0 LAN and wlan0 by toggling the eth0 MAC into a locally administered MAC. That is currently done by in user-space by adding a uci config item into /etc/config/network (More elegant solution might be setting it already in preinit phase.) Known issues: * wifi firmware file may not get created on the first boot after flashing on time to bring wifi normally up. Likely the overlay jffs2 is not yet ready for creating the firmware file. "wifi up" may still bring wifi up. Wifi will work normally at subsequent boots. * phy0 and phy1 may get assigned mixed, so that phy0 may be the 5GHz radio instead of the normal 2.4GHz, and vice versa for phy1. Does not happen always, but may happen. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [fix the wifi unit address in the dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Pisen WMM003N (Cloud Easy Power)Icenowy Zheng2018-08-143-0/+136
| | | | | | | | | | | | | | | | | | | | | Pisen WMM003N (sold under the name of Cloud Easy Power) is an AR9331-based router and power bank combo device. The device uses a stock firmware modified from OpenWRT for TP-Link TL-WR703N; however some GPIO definition is different on this device with TL-WR703N. An AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also added, and the stock Flash/RAM configuration is 8MiB/64MiB. The stock firmware is an old and heavily modified OpenWRT-based firmware, which has telnetd defaultly open, and the root password is "ifconfig" (quotation marks not included). The factory image format is not known yet, however the stock firmware ships the OpenWRT's sysupgrade command, and it can be used to install a newer firmware. Due to the lack of the access to the STM8 embedded controller, the SD slot is currently not usable (because it's muxed with the on-board USB port) and the AXP PMIC cannot be monitored. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* ar7: remove linux 3.18 supportKoen Vandeputte2018-08-1314-998/+0
| | | | | | | This target is on 4.9 currently. It seems the support for this old kernel never got dropped. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add missing USB packages into ASL26555-16MZoltan HERPAI2018-08-131-1/+1
| | | | | | | Mirror the package list from the 8M device profile to the 16M device profile. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 09:06:57 +0000