aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* mvebu: enable CONFIG_HW_RANDOMHannu Nyman2018-06-181-0/+1
| | | | | | | | | Enable the Hardware Random Number Generator Core infrastructure in kernel. Needed for hardware random number generator drivers like chaoskey Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com>
* ath79: fix rx ring buffer stall qca956xLucian Cristian2018-06-181-1/+2
| | | | | | when ported from ar71xx to ath79 the qca9560-eth was omitted Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-187-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ath79: add tl-wr1043nd-v4 support everything is workingLucian Cristian2018-06-185-11/+271
| | | | | | | tplink-safeloader: resize kernel partition kernel 4.14 is much bigger, resize the partition Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add ubiquiti unifi ap ac lite/lrLucian Cristian2018-06-184-0/+171
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: ag71xx: fix pll-data setting for ar7242/ar934x/qca955x/qca956xWeijie Gao2018-06-181-10/+7
| | | | | | | | | | | ar71xx/ar913x series use the old pll registers and settings. However started from ar7242, a new pll register is introduced and the pll setting is much simpler. This can be observed from dev-eth.c from the ar71xx target. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ath79: add support for Phicomm K2TWeijie Gao2018-06-187-0/+587
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* lantiq: atm: fix ifx_atm driver integrationKevin Darbyshire-Bryant2018-06-181-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77 we incorrectly updated our hack integration patch that updates atm/common.c +++ b/net/atm/common.c @@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc write_unlock_irq(&vcc_sklist_lock); } +struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL; +EXPORT_SYMBOL(ifx_atm_alloc_tx); + static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size) { struct sock *sk = sk_atm(vcc); + if (ifx_atm_alloc_tx != NULL) + return ifx_atm_alloc_tx(vcc, size) The correct solution is to drop our ifx_atm_alloc_tx replacement hack entirely and let the kernel do its thing. In reality neither pppoatm or BR2684 interfaces actually hit this code, so the incorrect integration would only be noticed with direct socket calls which we are unaware of a use-case. This is not the solution to pppoatm vc-mux failing to work which started the whole investigation, but let's fix it up anyway. With sincerest thanks to David Woodhouse <dwmw2@infradead.org> & Mathias Kresin <dev@kresin.me>. Tested-on: lantiq, BT HomeHub 5a Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.9 to 4.9.109Koen Vandeputte2018-06-182-4/+4
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* bcm53xx: exit if writing kernel during sysupgrade failsRafał Miłecki2018-06-181-2/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop not ready support for Luxul devicesRafał Miłecki2018-06-181-30/+0
| | | | | | | | Support for these devices isn't ready yet and it was only accidentally pushed in the commit 0da9303e5b44 ("mac80211: backport "brcmfmac: cleanup and some rework" from 4.17"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: replace espressobin spi patch with upstream oneTomasz Maciej Nowak2018-06-182-29/+45
| | | | | | | | | For easier future kernel bumps replace spi patch with upstream version slightly modified. The modification removes partition definitions which has been diffrent for some U-Boot versions. Also this removes unnecessary i2c definition which was in the old patch. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-182-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: add fix for armada 37xx cpufreq driverTomasz Maciej Nowak2018-06-181-0/+35
| | | | | | Backport from stable kernel tree fixing clock leak. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mediatek: mt7622: Do not deactivate CONFIG_BLK_DEVHauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | zram.ko needs CONFIG_BLK_DEV activated and it is by default for all other targets in OpenWrt. This makes zram.ko compile again. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53Hauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | | Neon and vfpv4 are mandatory extensions in the ARM64 instruction set now, do not activate them explicitly. GCC will make use of these extension now by default. This makes it possible to share the toolchain with other Cortex A53 SoCs. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: move Netgear build code into a common makefileZoltan HERPAI2018-06-182-23/+23
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kernel: bump 4.14 to 4.14.49Koen Vandeputte2018-06-187-21/+16
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86-64 Runtime-tested on: cns3xxx, imx6, x86-64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.108Koen Vandeputte2018-06-185-167/+189
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: add get_status_led to diag.shDavid Bauer2018-06-181-0/+4
| | | | | | | | | | | This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net>
* gemini: Cook SQ201 imagesLinus Walleij2018-06-182-0/+35
| | | | | | | | | This generates the "rd.gz" and "hddapp.tgz" that doesn't contain anything of the sort but rather the OpenWRT rootfs. It works the same way as how we generate the same layout for the NAS4220b. For some reason the ImageInfo file is different for the SQ201. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Add appropriate Wireless kernel modulesLinus Walleij2018-06-181-2/+3
| | | | | | | | | | | | The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a slot. Activate the appropriate kernel module. The Square One SQ201 has a Ralink RT61-based mini-PCI card. Activate the appropriate kernel modules. This fixes the previous error just activating the firmware: the kernel module will bring in the firmware it needs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Cook a WRGG firmware imageLinus Walleij2018-06-181-2/+10
| | | | | | | | | This makes the Gemini build a WRGG-type firmware update image for the DIR-685. This should hopefully install the kernel from the web firmware upgrade API on the product switching it permanently to use OpenWRT. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mac80211: backport "brcmfmac: cleanup and some rework" from 4.17Rafał Miłecki2018-06-171-0/+30
| | | | | | | | | | | It was described by Arend as: > This series is intended for 4.17 and includes following: > > * rework bus layer attach code. > * remove duplicate variable declaration. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix NAND partitions on D-Link DIR-885LRafał Miłecki2018-06-171-0/+39
| | | | | | | | | | This fixes missing rootfs on above device: [ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 (...) [ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) Fixes: 05cb6aa69f66 ("bcm53xx: replace linux,part-probe with a proper partitions subnode") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: clean up led config script files for all devicesJohann Neuhauser2018-06-167-34/+17
| | | | | | | | | 1. Move all status led definitions out of diag.sh into device dt as we use here a generic script hook. 2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix WNDR3800 supportHannu Nyman2018-06-161-12/+37
| | | | | | | | | | | | | | | | Fixes for WNDR3800 DTS: * fix bootcmd * name art partition to reference it for MACs * format firmware partition's address similarly as others * make u-boot-env read-only like in ar71xx * read wan and lan MACs from art * fix LED and button gpio values to match ar71xx (orange/green powerLED, reset button) * enable power LED in dts by alias led-status * define USB LED triggers and connect to USB port * change wifi button to KEY_RFKILL like in ar71xx Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: led-resets: add default-trigger propertyJohann Neuhauser2018-06-161-1/+4
| | | | | | | | | Add support for the common led property "linux,default-trigger". It allows to set a default led trigger via devicetree. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix usb led on wr-1043nd-v1Lucian Cristian2018-06-162-10/+1
| | | | | | | usb port was not triggered correctly also remove uneded wifi led trigger from the script Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: fixup TL-WR703N/TL-MR10U splitAlex Maclean2018-06-163-19/+13
| | | | | | | | | | | Readd SoC compatible strings and correct model names mangled in a51078f7354fac9e31f6956cbddc77aaef02c67b, cleanup dts to remove duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U USB power. Tested only on TL-WR703N due to lack of a TL-MR10U. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-166-1/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: use phytpt trigger for mt76 wirelessDavid Bauer2018-06-161-4/+4
| | | | | | | | | | | | | With this change, the LED trigger is independent from the (wireless) netdev name. The (wireless) netdev name can be easiliy changed in OpenWrt and would require an update of the netdev trigger settings each time it is done. This change is (for now) applied only to MT7628 devices from TP-Link, as we only had the possibility to test this change against two of those devices, namely a TL-WR841 v13 and a Archer C50 v3. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix mt7688 watchdog register base addrlbzhung2018-06-161-2/+2
| | | | | | | | | | | | | I found mt7688 watchdog not working. The watchdog registers are identical for mt7621 and mt7628/mt7688. The first watchdog related register is at 0x10000100, the last one - a 16bit sized - at 0x10000128. Set the correct register address and size in the dtsi file to get the watchdog working. Signed-off-by: lbzhung <gewalalb@gmail.com> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: fix mtu setting with kernel 4.14Mathias Kresin2018-06-161-11/+7
| | | | | | | | | | Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It's necessary to set a max_mtu if a mtu > 1500 is supported. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq-vdsl-fw: update to provide recent vectoring firmwareDaniel Golle2018-06-151-1/+1
| | | | | | | | | | | | | | Recent Speedport firmware downloads only work over HTTPS, so the user either needs to provide the already downloaded file or install ustream-ssl-* as well as ca-certificates or ca-bundle. So to get VDSL2 with vectoring on xRX200, simply run vdsl_fw_install.sh on the target and either provide the downloaded file as instructed or make sure the device is connected to the Internet and can download that HTTPS url itself. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "lantiq: get rid of ltq-vdsl-fw"Daniel Golle2018-06-151-0/+1
| | | | | | This reverts commit 0938233fcdef67d969f9429a10761cc640c6d56d. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: move wifi calibration EEPROMs out of base-filesDaniel Golle2018-06-145-160/+3
| | | | | | | | Ship EEPROM blobs for specific supported board only and don't have them lurking around in our source tree but rather download them from @github/RPi-Distro/firmware-nonfree upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: add brcmfmac-firmware-43455-sdio to DEFAULT_PACKAGESDaniel Golle2018-06-141-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: add RPi3+ wifi calibration dataDaniel Golle2018-06-142-0/+92
| | | | | | | | Add files from https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix conntrack fixup of offloaded flows on timeoutFelix Fietkau2018-06-143-9/+33
| | | | | | Fixes excessively long conntrack timeout of short lived connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix conntrack leak for flow_offload connectionsFelix Fietkau2018-06-133-28/+123
| | | | | | | This was caused by a race condition between offload teardown and conntrack gc bumping the timeout of offloaded connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: allow hardware NAT offload drivers to keep a priv pointerFelix Fietkau2018-06-131-0/+25
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: rename ethernet driver folder to the same one that upstream usesFelix Fietkau2018-06-1327-41/+0
| | | | | | | Preparation for sharing offload code with the mediatek target through generic files/ Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: avoid flow offload for connections with xfrm on the dst entry ↵Felix Fietkau2018-06-131-1/+4
| | | | | | (should fix IPSec) Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 15:16:26 +0000