aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-144-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-133-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: generic: Check kernel size for the TL-WDR4900Pawel Dembicki2019-04-131-0/+1
| | | | | | | | | | | TP-Link TL-WDR 4900 have u-boot with read-only env. Boot command read only 0x29F000 data from flash. Bigger images causes crc error. It can't be changed. This patch add kernel size checking. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
* mpc85xx: clean up device package selectionDavid Bauer2019-04-131-4/+2
| | | | | | | Remove wireless and USB packages from the device-specific package selection as they are already selected by the target itself. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove USB support from kernelDavid Bauer2019-04-133-15/+1
| | | | | | | | | | | | This removes USB support from the compiled kernel. Because of this, the kernel is just small enough for the TP-Link WDR4900 to boot the resulting kernel. This is necessary to support the WDR4900 in the upcoming 19.xx release. In the long run, this should be fixed with a second stage bootloader, as the vendor bootloader only loads the first 2684k bytes. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove unnecessary packages from I-O DATA ETG3-RINAGAKI Hiroshi2019-04-131-0/+1
| | | | | | | | I-O DATA ETG3-R is a wired router. So wireless-related packages are unnecessary and remove those packages from default configuration to reduce flash usage. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-134-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ramips: fix pinctrl to allow hardware i2c on WRTNODE2RDaniel Golle2019-04-111-1/+11
| | | | | | | | Instead of assigning I2C pins as GPIOs by default, leave it up to the user whether to install kmod-i2c-mt7621 and use them for hardware I2C instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: move and replace accepted patchDaniel Golle2019-04-111-12/+11
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* imx6: bump sdma firmware to 3.4Koen Vandeputte2019-04-091-0/+0
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-097-0/+280
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove more duplicate image build variablesDaniel Gimpelevich2019-04-093-22/+18
| | | | | | | | | Remove Netgear-specific image build variables which are set to the same value. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [reordering of variables, removed stray newline] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: Remove already applied patchHauke Mehrtens2019-04-081-214/+0
| | | | | | | This patch is already included in kernel v4.19.31. Fixes: 8df12d76c642 ("kernel: bump 4.19 to 4.19.34") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: Correct MAC address for WAN interface of Archer C7 v5Adrian Schmutzler2019-04-081-0/+4
| | | | | | | | | | | This device shares the network config with v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add "info" partition for TP-Link Archer C7 v5Adrian Schmutzler2019-04-081-1/+1
| | | | | | | | | | | | | | This adds the "info" MTD partition, as it is specified in the ath79 DTS: https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35 This is required to set the WAN MAC address, as it is build based on the LAN MAC address, which in turn has to be read from the "info" partition: https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add WPS button to TP-Link Archer C7v5Petr Štetiar2019-04-081-0/+7
| | | | | | | This patch adds currently missing support for the WPS button on TP-Link Archer C7v5. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Correct MAC address for WAN interface of Archer A7/C7 v5Adrian Schmutzler2019-04-081-0/+5
| | | | | | | | | | | These devices share the network config with C7v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Fix GPIO reset button on TP-Link Archer C7v5Adrian Schmutzler2019-04-083-7/+18
| | | | | | | | | | | | | The GPIO for the reset button for the Archer C7v5 changed from ar71xx to ath79. An investigation based on tests revealed that the A7v5 responds on "11", while the C7v5 responds on "5" as set for ar71xx. Thus, we just define this in the DTS files instead of in the common DTSI. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Utilize new LED modes from diag.sh for Archer A7/C7 v5Adrian Schmutzler2019-04-081-1/+4
| | | | | Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consolidate LEDs in Archer A7/C7 v5 DTSIAdrian Schmutzler2019-04-081-48/+46
| | | | | | | | Definition is split here without obvious reason. Just merge it (and align order to that from C7 v4). Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti airCube ISPChristian Mauderer2019-04-084-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-084-2/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCsPetr Štetiar2019-04-081-1/+8
| | | | | | | | | | | In ar71xx we check for stuck DMA on devices which fall in the is_ar724x SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x). In ath79 we're currently performing this check only for devices with ar7240 SoC, so this patch tries to sync the dma stuck checking behavior with what is being done in ar71xx. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)Petr Štetiar2019-04-081-2/+3
| | | | | | | | | It was reported, that latest ar71xx builds have broken networking on TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting the offending commit, everything is back to normal. Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: Add support for Ubiquity Bullet M (XW)Petr Štetiar2019-04-088-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recoveryPetr Štetiar2019-04-081-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is backport of the same functionality in ath79, from commit d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method") Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3801500 bytes Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44 Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW. 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: Add support for Toradex Apalis family of CoMsPetr Štetiar2019-04-0811-1/+495
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the following computer on modules (CoM) from Toradex[A]: Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC -40° to +85° C Temp Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC 0° to +70° C Temp Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC -40° to +85° C Temp Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC 0° to +70° C Temp I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on Eval[C] board as well. A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6 B. https://www.toradex.com/products/carrier-board/ixora-carrier-board C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board Flashing/recovery instructions: 1. Download and compile imx_loader for OpenWrt from https://github.com/ynezz/imx_loader 2. Enter recovery mode as desribed in https://developer.toradex.com/knowledge-base/imx-recovery-mode 3. Connect board via USB to the host computer, check that it's connected by lsusb: 15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip in RecoveryMode 4. Copy following OpenWrt images to imx_loader directory: SPL u-boot.img u-boot-with-spl.imx openwrt-imx6-apalis-recovery.scr openwrt-imx6-apalis-squashfs.combined.bin 5. Run imx_usb in imx_loader directory Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: image: Split imx6-sdcard image for reusabilityPetr Štetiar2019-04-081-3/+16
| | | | | | | I'm going to reuse the imx6-sdcard image commands for building of Apalis eMMC images. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.34Koen Vandeputte2019-04-0838-211/+100
| | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed: - 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch Altered: - 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch - 650-netfilter-add-xt_OFFLOAD-target.patch - 662-remove_pfifo_fast.patch - 332-arc-add-OWRTDTB-section.patch - 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch - 702-phy_add_aneg_done_function.patch New symbols: - ARC_IRQ_NO_AUTOSAVE - SUN50I_ERRATUM_UNKNOWN1 Compile-tested: cns3xxx, imx6, sunxi Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.111Koen Vandeputte2019-04-0810-18/+18
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.168Koen Vandeputte2019-04-081-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.110Koen Vandeputte2019-04-083-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: correct DTS for Belkin F9K1109v1 to include switch definitionKip Porterfield2019-04-061-0/+11
| | | | | | | | | Add switch definition for the rtl8367b switch to the DTS/DTSi for the Belkin F9K1109v1 that was mistakenly omitted from the initial commit. Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1) Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-065-7/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ramips: backport mt7621-spi from linux-next-20190329Chuanhong Guo2019-04-061-261/+213
| | | | | | | | | | | | | Upstream driver has gone through a series of cleanup and was moved from drivers/staging into drivers/spi. Backport it to replace our messy driver. Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de> [LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module] Tested-by: Rosen Penev <rosenp@gmail.com> Tested-by: Tian Xiao bo <peterwillcn@gmail.com> [Newifi-D2 MediaTek MT7621 ver:1 eco:3] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: Utilize tplink-safeloader definitionAdrian Schmutzler2019-04-062-19/+6
| | | | | | | | | | | | | | | | | Currently, tplink-safeloader definition is only used a base for another common definition. This patch adjusts tplink-safeloader so it can be actually used for some targets in generic-tp-link.mk. This patch is cosmetic except for the order of "check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged for the tplink_re350k-v1 . Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's extra IMAGE/sysupgrade.bin rule]
* ramips: enable R6120 USB powerDavid Bauer2019-04-062-1/+16
| | | | | | | Enable the USB power for the Netgear R6120. Otherwise, no power is supplied to an attached USB device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: engenius epg5000: add leds migration scriptTomasz Maciej Nowak2019-04-061-0/+16
| | | | | | | | | | | | | | | With transition from ar71xx to ath79 some of devices change their naming of LEDs. When upgrading from ar71xx target images this will require the user to adjust previously working configuration. This commit adds migration script which can be used to rename old names to new ones. With this previously working configuration will be automatically adjusted, wihtout user intervention. This commit adds migration case for EnGenius EPG5000, the wireless LEDs names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to epg5000:blue:wlan2g and epg5000:blue:wlan5g. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-063-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* target/octeon: Add Linux 4.19 supportDaniel Engberg2019-04-064-0/+392
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Linux 4.19 kernel, various cleanups listed below. Drop 170-cisco-hack.patch as these devices never seems to have been supported. Unset kernel symbols: * CONFIG_CAVIUM_CN63XXP1=y No supported hardware uses CN63XXP1 and it causes "slight decrease in performance" Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html * CONFIG_USB_OCTEON_EHCI=y CONFIG_USB_OCTEON_OHCI=y Deprecated Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.html https://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html Removed kernel symbols: * # CONFIG_ARCH_HIBERNATION_POSSIBLE=y * CONFIG_ARCH_SUSPEND_POSSIBLE=y These are not in if you do a vanilla config of a MIPS Octeon kernel and I can't find any references about support on this platform. * # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set * CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 No need to have this in by default, not defined in most other targets * CONFIG_CRASH_CORE=y Can't find any documentation why this should be enabled by default * CONFIG_DEBUG_INFO=y Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134 * CONFIG_DEBUG_SPINLOCK=y No need to have this in by default * CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120 Already set by default Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html * CONFIG_DETECT_HUNG_TASK=y No need to have this in by default, not defined in most other targets * CONFIG_HAVE_DEBUG_KMEMLEAK=y No need to have this in by default, not defined in most other targets * CONFIG_HAVE_DEBUG_STACKOVERFLOW=y No need to have this in by default * CONFIG_HAVE_IDE=y None of the supported devices have IDE * CONFIG_HZ=250 * # CONFIG_HZ_100 is not set * CONFIG_HZ_250=y This is broken with generic config * CONFIG_KALLSYMS=y No need to have this in by default, not defined in most other targets * CONFIG_KEXEC=y * CONFIG_KEXEC_CORE=y No need to have this in by default, not defined in most other targets * CONFIG_HAVE_KVM=y No need to have this in by default * CONFIG_SCHED_DEBUG=y No need to have this in by default, not defined in most other targets * CONFIG_SYSFS_DEPRECATED=y Deprecated symbol Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html * CONFIG_SYSFS_DEPRECATED_V2=y Discouraged usage in general Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html * CONFIG_UNINLINE_SPIN_UNLOCK=y No need to have this in by default, not defined in most other targets Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137 * CONFIG_ZLIB_INFLATE=y No need to have this in by default, not defined in most other targets Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mvebu: sysupgrade: sdcard: keep user added partitonsTomasz Maciej Nowak2019-04-065-11/+83
| | | | | | | | Currently sysupgrade overwrites whole disk and destroys partitions added by user. Sync the sysupgrade code with the one present in x86 target to remedy this behaviour. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: base-files: autodetect upgrade deviceTomasz Maciej Nowak2019-04-062-10/+18
| | | | | | | Since some boards could be also booted from other mediums than SD card, lets make the upgrade block device autodetected. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: shrink amount of packages and reorganize themTomasz Maciej Nowak2019-04-066-11/+15
| | | | | | | | | Since most of devices using SD card image to boot, use ext4 as boot files system we can drop fat fs related packages. Also move packages which are added repeatedly across subtargets to their default packages, with droping the ones that are enabled in target kernel configugation. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: use ext4 for clearfog image bootfsTomasz Maciej Nowak2019-04-061-2/+2
| | | | | | | This will allow to drop additional packages and shrink image size. Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: make bootfs size for sdcard image configurableTomasz Maciej Nowak2019-04-062-11/+7
| | | | | | | Let's take this oportunity to implement boot-part and rootfs-part feature flags. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* zynq: replace storage related configs by packagesLuis Araneda2019-04-062-10/+3
| | | | | | | Select build-in packages by default and remove the associated kernel configs Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: replace CAN kconfig options by device packagesLuis Araneda2019-04-062-21/+1
| | | | | | | | | | The options are managed on a generic way by the can kmod packages Additionally, select can packages only for devices that currently has CAN enabled, which is only the ZC702 Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: kernel: remove video/camera kconfig optionsLuis Araneda2019-04-061-12/+0
| | | | | | | | | | The options are managed on a generic way by video packages Additionally, only one of the currently supported boards has a camera interface, but it requires programming the FPGA fabric first Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: kernel: remove sound kconfig optionsLuis Araneda2019-04-061-19/+0
| | | | | | | | | | | The options are managed on a generic way by the sound kmod packages Additionally, none of the currently supported boards have sound support out of the box, as they require programming the FPGA fabric first Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: kernel: refresh configLuis Araneda2019-04-061-14/+2
| | | | Signed-off-by: Luis Araneda <luaraneda@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-06 15:42:01 +0000