aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/x86/modules.mk
Commit message (Collapse)AuthorAgeFilesLines
* Revert "gpio-cdev: add nu801 userspace driver"Christian Lamparter2021-10-101-1/+1
| | | | | | | | | | | This reverts commit f536f5ebddd9c532a08ac4a9be3ef0c02f7bfeb8. As Hauke commented, this causes builder failures on 5.4 kernels. This revert includes changes to the mx100 kernel modules dependency as well as the uci led definitions. Tested-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: add support for Meraki MX100Chris Blake2021-10-101-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit will add support for the Meraki MX100 in OpenWRT. Specs: * CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T * Memory: 4GB DDR3 1600 ECC * Storage: 1GB USB NAND, 1TB SATA HDD * Wireless: None * Wired: 10x 1Gb RJ45, 2x 1Gb SFP UART: The UART header is named CONN11 and is found in the center of the mainboard. The pinout from Pin 1 (marked with a black triangle) to pin 4 is below: Pin 1: VCC Pin 2: TX Pin 3: RX Pin 4: GND Note that VCC is not required for UART on this device. Booting: 1. Flash/burn one of the images from this repo to a flash drive. 2. Take the top off the MX100, and unplug the SATA cable from the HDD. 3. Hook up UART to the MX100, plug in the USB drive, and then power up the device. 4. At the BIOS prompt, quickly press F7 and then scroll to the Save & Exit tab. 5. Scroll down to Boot Override, and select the UEFI entry for your jumpdrive. Note: UEFI booting will fail if the SATA cable for the HDD is plugged in. The issue is explained under the Flashing instructions. Flashing: 1. Ensure the MX100 is powered down, and not plugged into power. 2. Take the top off the MX100, and unplug the SATA cable from the HDD. 3. Using the Mini USB female port found by the SATA port on the motherboard, flash one of the images to the system. Example: `dd if=image of=/dev/sdb conv=fdatasync` where sdb is the USB device for the MX100's NAND. 4. Unplug the Mini USB, hook up UART to the MX100, and then power up the device. 5. At the BIOS prompt, quickly press F7 and then scroll to the Boot tab. 6. Change the boot order and set UEFI: USB DISK 2.0 as first, and USB DISK 2.0 as second. Disable the other boot options. 7. Go to Save & Exit, and then select Save Changes and Reset Note that OpenWRT will fail to boot in UEFI mode when the SATA hard drive is plugged in. To fix this, boot with the SATA disk unplugged and then run the following command: `sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg` Once the above is ran, OpenWRT will boot when the HDD is plugged into SATA. The reason this happens is the UEFI implementation for the MX100 will always set anything on SATA to HD0 instead of the onboard USB storage, so we have to accomidate it since OpenWRT's GRUB does not support detecting a boot disk via UUID. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: amd-xgbe: add missing dependencies on 5.10Chuanhong Guo2021-04-181-1/+1
| | | | | | | | | fix the following build error when building with test kernel: Package kmod-amd-xgbe is missing dependencies for the following libraries: mdio_devres.ko Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* x86/64: Add support for AMD SOC Ethernet controllerZheng Bao2021-04-171-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This feature is already supported in kernel. Add definition and configuration in Makefile of OpenWRT. It is tested on board Dibbler with processor V1605B. Dmesg is as below. -------------------------------------------- [ 0.317122] smpboot: CPU0: AMD Ryzen Embedded V1605B with Radeon Vega Gfx (family: 0x17, model: 0x11, stepping: 0x0) [ 8.227270] libphy: amd-xgbe-mii: probed [ 8.228189] amd-xgbe 0000:02:00.1 eth0: net device enabled [ 8.228999] libphy: amd-xgbe-mii: probed [ 8.229921] amd-xgbe 0000:02:00.2 eth1: net device enabled ..... [ 11.760869] br-lan: port 1(eth0) entered blocking state [ 11.761365] br-lan: port 1(eth0) entered disabled state [ 11.762019] device eth0 entered promiscuous mode [ 11.785285] 8021q: adding VLAN 0 to HW filter on device eth1 [ 16.881431] amd-xgbe 0000:02:00.1 eth0: Link is Up - 1Gbps/Full - flow control off [ 16.882108] br-lan: port 1(eth0) entered blocking state [ 16.882583] br-lan: port 1(eth0) entered forwarding state [ 16.883249] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready ----------------------------------------------- Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
* x86: add support for AWS T3 instancesAlberto Bursi2021-03-011-0/+17
| | | | | | | | | | | | | | | | | Amazon AWS T3 cloud instances require kernel support for the Elastic Fabric Adapter to access storage and for Elastic Network Adapter to use network interfaces. Since the Fabric Adapter is needed to access root filesystem, enable in x86_64 kernel. Elastic Network Adapter goes in a module, and add this module to default list in x86_64. The module is set to AutoLoad because AutoProbe does not seem to load it. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-101-3/+1
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: add pcengines-apu2 module descriptionFlorian Eckert2020-06-261-0/+17
| | | | | | | | Add a module description for the new pcengnies-apu2 device driver. This driver supports the front button and LEDs on the PC Engines APUv2/APUv3 boards. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* x86: avoid underscore in package nameSungbo Eo2020-02-231-3/+3
| | | | | | | As 07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows, underscores might cause build failures. Replace underscore with dash. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* x86: add kernel module for sp5100_tco watchdogChris Blake2017-01-161-0/+15
| | | | | | | | | | | This change adds the sp5100_tco driver as a kernel module for the x86 target. Specifically, this can be used by the PCEngines APU2/APU3. The reason for having this as a kernel module is to allow users to load/unload it on demand, as the I2C interface on the APU2/APU3 will not work while this module is loaded. More info can be found on GitHub at https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736 Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* x86: add kernel module for AMD CS5535/CS5536 audio chipsetCezary Jackiewicz2017-01-061-0/+21
| | | | | | | | Add support for the integrated AC97 sound device on motherboards with AMD CS5535/CS5536 chipsets. Tested on Wyse Winterm S30. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* x86: remove obsolete modules.mkFelix Fietkau2016-05-121-22/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86: merge all geode based subtargets into oneFelix Fietkau2015-03-161-308/+0
| | | | | | | | | Build all geode platform drivers into the kernel Remove kmod-* packages for these drivers Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44809
* x86: fix kmod-gpio-pc8736x dependenciesHauke Mehrtens2013-07-191-1/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37447
* merge the RDC R-321x target as a subtarget of x86Florian Fainelli2012-10-151-0/+16
| | | | SVN-Revision: 33779
* move leds modules back to target modules.mkFlorian Fainelli2012-07-251-0/+32
| | | | SVN-Revision: 32851
* move i2c modules back to target modules.mkFlorian Fainelli2012-07-251-0/+34
| | | | SVN-Revision: 32850
* move more x86-specific modules back to target modules.mkFlorian Fainelli2012-07-251-0/+175
| | | | SVN-Revision: 32848
* move x86 specific ide/pata modules to x86' modules.mkFlorian Fainelli2012-07-251-0/+73
SVN-Revision: 32846
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-26 05:45:17 +0000