aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/rockchip
Commit message (Collapse)AuthorAgeFilesLines
...
* rockchip: remove useless echo in 40-net-smp-affinityAdrian Schmutzler2020-08-171-1/+1
| | | | | | The command in the $() brackets will already provide the same output. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Move CONFIG_IONIC to generic kernel configHauke Mehrtens2020-08-101-1/+0
| | | | | | | It is deactivated everywhere, just set this in the generic config. Acked-by: Yousong Zhou <yszhou4tech@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* treewide: make dependency on kmod-usb-net selectiveAdrian Schmutzler2020-08-101-1/+1
| | | | | | | | A bunch of kernel modules depends on kmod-usb-net, but does not select it. Make AddDepends/usb-net selective, so we can drop some redundant +kmod-usb-net definitions for DEVICE_PACKAGES. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rockchip: enable rockchip-thermalDavid Bauer2020-07-291-1/+1
| | | | | | | | | Enable the rockchip-thermal driver to allow reading the temperature of the SoC. Tested on NanoPi R2S Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: distribute net interruptsDavid Bauer2020-07-281-0/+30
| | | | | | | | | | | | This adds a hotplug script for distributing interrupts of eth0 and eth1 across different cores. Otherwise the forwarding performance between eth0 and eth1 is severely affected. The existing SMP distribution mechanic in OpenWrt can't be used here, as the actual device IRQ has to be moved to dedicated cores. In case of eth1, this is in fact the USB3 controller. Signed-off-by: David Bauer <mail@david-bauer.net>
* arm64: dts: rockchip: Add txpbl node for RK3399/RK3328David Bauer2020-07-281-0/+54
| | | | | | | | | | | | | | | | | | | | Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue where tx checksumming does not work with packets larger than 1498. The default Programmable Buffer Length for TX in these GMAC's is not suitable for MTUs higher than 1498. The workaround is to disable TX offloading with 'ethtool -K eth0 tx off rx off' causing performance impacts as it disables hardware checksumming. This patch sets snps,txpbl to 0x4 which is a safe number tested ok for the most popular MTU value of 1500. For reference, see https://lkml.org/lkml/2019/4/1/1382. Signed-off-by: Carlos de Paula <me@carlosedp.com> Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: enable LAN LED configurationDavid Bauer2020-07-283-0/+156
| | | | | | This enables the LEDs on the LAN interfaces. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: add NanoPi R2S supportDavid Bauer2020-07-289-6/+609
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3328 ARM64 (4 cores) 1GB DDR4 RAM 2x 1000 Base-T 3 LEDs (LAN / WAN / SYS) 1 Button (Reset) Micro-SD slot USB 2.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card using dd. MAC-address ----------- The vendor code supports reading a MAC address from an EEPROM connected via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC address in binary at offset 0xfa. However, my two units didn't come with such an EEPROM soldered on. The EEPROM should be placed between the SoC and the GPIO pins on the board. (U10) Generating rendom MAC addresses works around this issue. Otherwise, all boards running the same image have identical MAC addresses. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: allow for multiple boot-scriptsDavid Bauer2020-07-281-1/+1
| | | | | | | | Add support for select a bootscript depending on the device built. This is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in order to produce output on the debug UART. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: don't disable timer LED triggerDavid Bauer2020-07-131-1/+0
| | | | | | | | The timer LED trigger is enabled in all targets (except for lantiq xway-legacy). It's necessary for the OpenWrt preinit LED pattern to work. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: use downstream GPIO button implementationDavid Bauer2020-07-132-2/+1
| | | | | | | | Use the OpenWrt netlink GPIO button implementation to forward button presses to procd. This is necessary to make failsafe-mode access using a button possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-111-3/+1
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rockchip: add support for Pine64 RockPro64Tobias Mädel2020-04-2010-0/+1051
This adds the new rockchip target and support for RockPro64 RK3399 Flash: 16 MiB SPI NOR RAM: 2 GiB/4 GiB LPDDR4 SoC: RK3399 USB: 2x USB 2.0, 1x USB 3.0, 1x USB-C Ethernet: 1x GbE PCIe: PCIe 2.0, 4 lanes Storage: eMMC or SD card Optional SDIO wifi/bt module The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector, 6 ARM64 cores (4 little, 2 big), plenty of RAM and storage. By default the single Gigabit-Ethernet port is configured as the LAN port. Installation of the firware is possible by dd'ing the image to an SD card or the eMMC flash. Serial: 3v3 1500000 8n1 U-boot is build from the mainline tree and integrated into the images. Required ATF to build u-boot is downloaded from a CI build bot. Signed-off-by: Tobias Mädel <t.maedel@alfeld.de> Tested-by: Tobias Schramm <t.schramm@manjaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 17:47:58 +0000