aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips/mt7621: disable the cpufreq driverFelix Fietkau2023-07-081-7/+3
| | | | | | | It causes a noticeable performance decrease Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit dc38199b96ee3ef0ac52873893c42e28fa0564fa)
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-034-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5)
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-027-3/+561
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
* ramips: sercomm.mk: preparation for Sercomm s1500 devices supportMikhail Zhilkin2023-07-021-5/+9
| | | | | | | | | | | | | | This commit moves a part of the code from the "sercomm-factory-cqr" recipe to the separate "sercomm-mkhash" recipe. This simplifies recipes and allows insert additional recipes between these code blocks (required for the future support for Beeline SmartBox PRO router). dd automatically fills the file by 0x00 if the filesize is less than offset where we start writing. We drop such dd command so we need to add --extra-padding-size 0x190 to the sercomm-pid.py call. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit f560be583a858bc3099f2b1f0aa0ddec62cfd91c)
* kernel: bump 5.15 to 5.15.118John Audia2023-06-252-4/+4
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 1f5fce27c195373fedcf233a48470de97752058f)
* ramips: fix lan leds for Wavlink WL-WN535K1Davide Fioravanti2023-06-253-5/+5
| | | | | | | | | | Previously both lan1 and lan2 leds were wrongly labelled as lan2. Moreover they were connected to the wrong lan port. Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1") Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit c71dada92654a53c63bbc5bebcc40fe924750ed7)
* ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)Kim DoHyoung2023-06-253-1/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr> (cherry picked from commit 0bbd5699c81d6887c4d895e85b56d8c23b1211ec)
* ramips: Add support for Beeline SmartBox TURBO+Maximilian Weinmann2023-06-176-9/+319
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router. Device specification -------------------- SoC Type: MediaTek MT7621AT (880 MHz, 2 cores) RAM (Nanya NT5CC64M16GP): 128 MiB Flash (Macronix MX30LF1G18AC): 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615N): a/n/ac, 4x4 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) USB ports: 1xUSB3.0 Buttons: 2 button (reset, wps) LEDs: Red, Green, Blue Zigbee (EFR32MG1B232GG): 3.0 Stock bootloader: U-Boot 1.1.3 Power: 12 VDC, 1.5 A Installation (fw 2.0.9) ----------------------- 1. Login to the web interface under SuperUser (root) credentials. Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the device written on the backplate stick. 2. Navigate to Setting -> WAN. Add: Name - WAN1 Connection Type - Static IP Address - 172.16.0.1 Netmask - 255.255.255.0 Save -> Apply. Set default: WAN1 3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add: Protocol - SSH Port - 22 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN Interface - WAN1 Save ->Apply Add: Protocol - HTTP Port - 80 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN interface - WAN1 Save -> Apply 4. Set up your PC ethernet: Connection Type - Static IP Address - 172.16.0.2 Netmask - 255.255.255.0 Gateway - 172.16.0.1 5. Connect PC using ethernet cable to the WAN port of the router 6. Connect to the router using SSH shell under SuperUser account 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface under admin account 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 171.16.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses (fw 2.0.9) ------------------------ +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:e8 | | WAN | label + 1 | *:e9 | | 2g | label + 4 | *:ec | | 5g | label + 5 | *:ed | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 Factory image format -------------------- +---+-------------------+-------------+--------------------+ | # | Offset | Size | Description | +---+-------------------+-------------+--------------------+ | 1 | 0x0 | 0x200 | Tag Header Factory | | 2 | 0x200 | 0x100 | Tag Header Kernel1 | | 3 | 0x300 | 0x100 | Tag Header Kernel2 | | 4 | 0x400 | SIZE_KERNEL | Kernel | | 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) | +---+-------------------+-------------+--------------------+ Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org> (cherry picked from commit 8fcfb21b16e7537b9a871a1f67cb218c6be93149)
* kernel: bump 5.15 to 5.15.116John Audia2023-06-171-1/+1
| | | | | | | | | | | All patches rebased automatically. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 5dc78d8f18e8f536317d9438b096a484a9c49862)
* ramips: mt7621-dts: move wan port to gmac1 YunCore FAP-640Volodymyr Puiul2023-06-111-7/+20
| | | | | | | | move wan port to gmac1 to achieve 2Gbps CPU bandwidth between wan and lan on YunCore FAP-640 Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com> (cherry picked from commit 47c2d50c0312412582fff7950b843d619400da9f)
* ramips: fix button definitions for Zyxel WSM20Thomas Schröder2023-06-101-2/+2
| | | | | | | | | Setting the events of the WPS and LED buttons to the best matching values based from the documentation: <https://openwrt.org/docs/guide-user/hardware/hardware.button#procd_buttons> Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com> (cherry picked from commit b0120f7c8bb35088f298f00eb4a630f62fb4183f)
* ramips: fix first boot network configuration for TOZED ZLT S12 PROArınç ÜNAL2023-06-101-0/+1
| | | | | | | | | | | | The network configuration at first boot for TOZED ZLT S12 PRO lacks setting up the LAN and WAN network interfaces. Address this. The WAN port is advertised as WAN/LAN on the device and is put on LAN on stock firmware so put it on LAN here as well. Fixes: ce1f9fa625 ("ramips: add support for TOZED ZLT S12 PRO") Reported-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit b61253f92abb4c0d21ec7358a74438eae8d7e6b4)
* ramips: enable LED button for TP-Link EC330-G5u v1Mikhail Zhilkin2023-06-081-0/+16
| | | | | | | | | | The device already has LED push button (KEY_LIGHTS_TOGGLE) and exported GPIO control "led-light". This commit adds button handler script for switching on/off all device LEDs. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit d955b41275eaf93b7600f8eb7d706f40302f26c2)
* ramips: tplink,mr600v2: fix image generation for sysupgrade imageAndreas Böhler2023-06-081-0/+3
| | | | | | | | | | | The MR600v2 does not find its rootfs if it is neither directly after the kernel or aligned to an erase block boundary (64k). This aligns the rootfs to 0x10000 allowing the device to boot again. Based on investigation by forum user relghuar. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 46b51e9e992884c81f4838440cd2967e67db3a79)
* ramips: fix lzma-loader for ASIARF boardsDaniel Danzberger2023-06-071-0/+2
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> (cherry picked from commit 29a5cb7a8b105ca6534bba63edcec48ae935c078)
* ramips: correct page read return value of the mt7621 nand driverShiji Yang2023-05-291-5/+9
| | | | | | | | | | | | | | read_page() need to return maximum number of bitflips instead of the accumulated number. Change takes from upstream mt7621 u-boot [1]. * @read_page: function to read a page according to the ECC generator * requirements; returns maximum number of bitflips * corrected in any single ECC step, -EIO hw error [1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/ Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 2fbb91d73ffecc7d033e5bb0b550d664ef9e0f91)
* mediatek: sync MT7988 USXGMII with SDK driverDaniel Golle2023-05-291-2/+2
| | | | | | | | | | The USXGMII driver in SDK was heavily refactored, some bugs have been fixed and it has switched to use phylink_pcs. Follow up with changes in SDK driver and sync our on-top-of-mainline driver with the SDK driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit ba58245e83714de5f47b4b0fc0369930c3661cab)
* ramips: mark patches accepted upstreamNick Hainke2023-05-299-0/+0
| | | | | | | | Add kernel tags to the patches that got accepted upstream. Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit 2388b119de9279d7adaa525c7ba502fcae1fe187) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: mt7530: backport support for the MT7988 built-in switchDaniel Golle2023-05-241-0/+2
| | | | | | | | | | | | | | | | | Backport commits adding support for the MT7988 built-in switch to the mt7530 driver. This change results in the Kconfig symbol NET_DSA_MT7530 to be extended by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530) and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in switch of the MT7988 SoC). Select NET_DSA_MT7530_MDIO for all targets previously selecting NET_DSA_MT7530, with the exception of mediatek/filogic which also selects NET_DSA_MT7530_MMIO. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 958fdf36e35c814eb83faf2c39db4ca379c921b5)
* generic: add support for MediaTek NETSYS v3Daniel Golle2023-05-241-2/+2
| | | | | | | | In order to support Ethernet on the MT7988 SoC add support for NETSYS v3 as well as new paths and USXGMII SerDes to the mtk_eth_soc driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 6983a215d9d1966f95bc5b1c0045c200948b2079)
* treewide: Disable building 32M RAM devicesFelix Baumann2023-05-215-0/+57
| | | | | | | | Following deprecation notice[1] in 21.02, disable targets with 32M of RAM [1] https://openwrt.org/supported_devices/864_warning Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: fix Xiaomi Router 3G/Pro LEDsDENG Qingfang2023-05-202-20/+53
| | | | | | | | | | The PHY name has been changed to "mt7530-0" since IRQ support was added to MT7530 driver. Fixes: f9cfe7af1f1f ("kernel: backport MT7530 IRQ support") Signed-off-by: DENG Qingfang <dqfext@gmail.com> (node names, added color, function+function-enumerator properties) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: remove obsolete kernel version switchesAleksander Jan Bajkowski2023-05-205-39/+0
| | | | | | | This removes unneeded kernel version switches from the targets after kernel 5.10 has been dropped. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ramips: fix build error on Airlink AR670WShiji Yang2023-05-191-1/+1
| | | | | | | | | | The 'KERNEL' is not referenced by other objects, so double '$$' will cause shell unable to parse the variable 'BLOCKSIZE': dd ... bs=$(BLOCKSIZE) conv=sync bash: line 1: BLOCKSIZE: command not found Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices) Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add basic common recipe for nand flash devicesShiji Yang2023-05-181-207/+47
| | | | | | | | These same codes are repeated for many devices now, it's better to move them to shared definition. This commit also add the missing KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: set default BLOCKSIZE to 64k for nor flash devicesShiji Yang2023-05-187-74/+2
| | | | | | | | | In kernel 5.15, the default erase sector size of the nor flash has been switched from 4k to 64k. This may cause the configuration not be preserved across upgrades. To avoid this issue, change the default BLOCKSIZE to 64k. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: enable variable sector size erasure for all subtargetShiji Yang2023-05-184-2/+4
| | | | | | | | | Make use of minor sector size (4k) on supported flash chips to improve spi read/write performance. Tested on ramips/mt7628: Motorola MWR03 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: rename to D-Team Newifi D2 and Lenovo Newifi D1Arınç ÜNAL2023-05-183-6/+6
| | | | | | | Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1. Let's not make naming exceptions because of marketing whims. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for TOZED ZLT S12 PROArınç ÜNAL2023-05-184-0/+262
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: Fix Wireless Frequencies for HYC-G920Muhammad AL-Qadhy2023-05-181-0/+2
| | | | | | Fix wireless frequencies to show correct wireless interfaces. Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
* ramips: remove device tree legacy compatibilityNick Hainke2023-05-122-64/+0
| | | | | | | We switched to 5.15 kernel, so we don't need to maintain 5.10 compatibility anymore. Signed-off-by: Nick Hainke <vincent@systemli.org>
* treewide: remove files for building 5.10 kernelNick Hainke2023-05-1244-6092/+0
| | | | | | | | | | | All targets are bumped to 5.15. Remove the old 5.10 patches, configs and files using: find target/linux -iname '*-5.10' -exec rm -r {} \; Further, remove the 5.10 include. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: 5.15: add patch fixing compilation warning for hsdma-mt7621Christian Marangi2023-05-121-0/+31
| | | | | | | | | | | Add patch fixing compilation warning for hsdma-mt7621: drivers/staging/mt7621-dma/hsdma-mt7621.c: In function 'mtk_hsdma_probe': drivers/staging/mt7621-dma/hsdma-mt7621.c:685:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 685 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: rt3833: fix compilation warning from device_reset in fe_probeChristian Marangi2023-05-121-1/+3
| | | | | | | | | | | | | Fix compilation warning from device_reset in fe_probe. On fail print a warning but don't fail probe. Fix compilation warning: drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe': drivers/net/ethernet/ralink/mtk_eth_soc.c:1564:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 1564 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: mt76x8: fix compilation warning in esw driverChristian Marangi2023-05-121-2/+1
| | | | | | | | | | | | | | | | | | | | | | | Fix compilation warning for debug string in esw driver: drivers/net/ethernet/ralink/esw_rt3050.c:1535:9: note: in expansion of macro 'dev_info' 1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n", | ^~~~~~~~ drivers/net/ethernet/ralink/esw_rt3050.c:1535:53: note: format string is defined here 1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n", | ~~~~^ | | | long unsigned int | %08p cc1: all warnings being treated as errors Fix unused variable causing compilation warning: drivers/net/ethernet/ralink/esw_rt3050.c: In function 'esw_interrupt': drivers/net/ethernet/ralink/esw_rt3050.c:769:13: error: unused variable 'i' [-Werror=unused-variable] 769 | int i; | ^ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mtk-mcc: move cmd_buf for dbg under ifdefChristian Marangi2023-05-121-2/+3
| | | | | | | | | | Move cmd_buf for dbg under ifdef to fix compilation warning: drivers/mmc/host/mtk-mmc/dbg.c:51:13: error: 'cmd_buf' defined but not used [-Werror=unused-variable] 51 | static char cmd_buf[256]; | ^~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ralink: mt7620: fix compilation warning for device_reset in i2s driverChristian Marangi2023-05-121-2/+6
| | | | | | | | | | | | | Fix compilation warning for device_reset in i2s driver. Fix compilation warning: sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe': sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 885 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errorralink: mt7620: fix compilation warning for device_reset in i2s driver Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: 5.15: handle return from device_reset in I2C driverChristian Marangi2023-05-121-2/+7
| | | | | | | | | | | | | | Handle return from device reset in I2C driver. Don't fail on device_reset error but print a warning. Fix compilation warning: sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe': sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 885 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mt7620: handle request_irq fail in gsw ethernet driverChristian Marangi2023-05-121-2/+7
| | | | | | | | | | | | | | Handle return from request_irq in gsw ethernet driver. Fix compilation warning: drivers/net/ethernet/ralink/gsw_mt7620.c: In function 'mtk_gsw_init': drivers/net/ethernet/ralink/gsw_mt7620.c:236:17: error: ignoring return value of 'request_irq' declared with attribute 'warn_unused_result' [-Werror=unused-result] 236 | request_irq(gsw->irq, gsw_interrupt_mt7620, 0, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 237 | "gsw", priv); | ~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: 5.15: handle error from device_reset in SPI ralink driverChristian Marangi2023-05-121-3/+8
| | | | | | | | | | | | | Handle error from device reset in SPI ralink driver fixing compilation warning: drivers/spi/spi-rt2880.c: In function 'rt2880_spi_probe': drivers/spi/spi-rt2880.c:474:17: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result] 474 | device_reset(&pdev->dev); | ^~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: add support for Linksys RE7000Christoph Krapp2023-05-093-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com>
* ramips: fix dts file name for SNR-CPE-ME1Maximilian Weinmann2023-05-081-0/+0
| | | | | | | | | Rename file mt7621_snr_snr-spe-me-1.dts Fixes: #12562 Fixes: ecdb248 ("ramips: add support for SNR-CPE-ME1") Tested-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: add support for SNR-CPE-ME1Maximilian Weinmann2023-05-073-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 16 MiB (GD25Q128CSIG) - WLAN : 2.4 GHz (MediaTek MT7603EN) 5 GHz (MediaTek MT7610EN) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (in SoC) - USB : 3.0 x1 - UART : through-hole on PCB - [J4] 3.3V, RX, TX, GND (57600n8) - Power : 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME1 to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: mt7621: rename Asus RT-AC57U to v1Felix Baumann2023-05-062-4/+6
| | | | | | rename RT-AC57U to avoid confusion with unsupported revisions 2 and 3 Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-025-52/+137
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: add factory image for TP-Link EC330-G5u v1Mikhail Zhilkin2023-04-291-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows to install OpenWrt without connecting a serial cable (UART). Installation using factory image -------------------------------- Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link firmware. 1. Login to the router web interface (http://192.168.0.1/ by default) and save running config to "conf.bin" file 2. Open configuration file in any TP-Link config editor (e.g. https://jahed.github.io/tp-link-config-editor/) 3. Find "DeviceInfo" section and insert a new string "<Description val="Modem Router`telnetd -p 1023 -l login`" />" according to the following example: <DeviceInfo> ... <Description val="Modem Router`telnetd -p 1023 -l login`" /> ... </DeviceInfo> 4. Save configuration file and upload changed configuration using stock firmware interface 5. Login using telnet to IP:192.168.0.1 (Username:admin, password:1234) 6. Run "cat /proc/mtd | grep mtd7" a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000', then install stock firmware using web interface to toggle booted firmware image from "os1" to "os0" b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000', then all is ok, go to the next step 7. Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100 in this example) 8. Login using telnet to 192.168.0.1 9. Download OpenWrt factory.bin image from the tftp server: cd /tmp tftp -g -r factory.bin 192.168.0.100 10. Write OpenWrt factory.bin image: dd if=/tmp/factory.bin of=/dev/mtdblock1 11. Power cycle the router Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: TP-Link EC330-G5u v1: switch to mac-address-asciiMikhail Zhilkin2023-04-293-10/+26
| | | | | | | | | | | | | The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd in ascii format. This commit makes the router use of "mac-address-ascii" in dts. After the change: 1. All MAC addresses are explicitly assigned in dts (the workarounds in network scripts are no longer needed); 2. gmac0 (eth0) MAC address is no longer random. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: lzma-loader: Refactor loaderAntonio Vázquez2023-04-299-87/+75
| | | | | | | | | * Delete unused lantiq makefile * Delete redundant makefiles and unify them into the main makefile * Refactor and unify board code into a single file * Add support and review subtarget specific board support Signed-off-by: Antonio Vázquez <antoniovazquezblanco@gmail.com>
* ramips: add support for D-Link DAP-1620 B1Rani Hod2023-04-295-8/+191
| | | | | | | | | | | | | | | | | | | | | | | | | The DAP-1620 rev B is a wall-plug AC1300 repeater. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI NOR - MT7615DN 2x2 802.11n +2x2 802.11ac (DBDC) - Ethernet: 1 port 10/100/1000 - Status LEDs (1x red+green) - LED RSSI bargraph (2x green, 1x red+green) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tail -c+117 DAP1620B1_FW212B03.bin | \ openssl aes-256-cbc -d -md md5 -out decrypted.bin \ -k 905503a4e0c3cd3c1ce062246de427a68962347e - flash decrypted.bin via D-Link Web Recovery Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: mt7621: add support for ZyXEL WSM20Andreas Böhler2023-04-296-1/+322
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 22:25:04 +0000