aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/rt288x
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add AW9523 I2C GPIO expander driverDavid Bauer2021-06-272-0/+2
| | | | | | | | | | | | | | This adds a driver for the AW9523 I2C GPIO expander. This driver is required to make LEDs as well as buttons on the Tenbay T-MB5EU-V01 work. This driver already had several upstream iterations. I'm working to push this driver to mainline. Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287 Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-212-4/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: 5.10: refresh configsIlya Lipnitskiy2021-03-061-4/+4
| | | | | | | | Run-tested on Ubiquiti EdgeRouter X. Compile tested on all other subtargets. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: copy config-5.4 to config-5.10Ilya Lipnitskiy2021-03-061-0/+177
| | | | | | Strict copy, no changes made. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* Revert "ramips: add support for kernel 5.10"Adrian Schmutzler2021-03-061-177/+0
| | | | | | | | | This reverts commit b4aad29a1d7ad77d67073c1c54b28c429c64ed9b. This was accidentally folded into a single commit. Remove it and apply it properly again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for kernel 5.10Ilya Lipnitskiy2021-03-051-0/+177
| | | | | | | | | | | | | | | | | | | | | | | | | Enable testing kernel. Delete upstreamed patches: 0098-disable_cm.patch can be dropped, upstream fixed CM handling. Fix compile errors by using new kernel APIs. Fix fuzz by manually editing patches to ensure the code goes in the right place. For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit a307593a6 to keep the OpenWrt ralink driver operational. Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693 and #3952. Rename patches to follow the 3-digit classification from the OpenWrt Developer Guide. Run automatic quilt refresh. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: 5.4: refresh configsIlya Lipnitskiy2021-03-051-53/+3
| | | | | | Automatic refresh by running make kernel_oldconfig on each target. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: remove set_wifi_led function in 01_ledsAdrian Schmutzler2020-10-021-7/+3
| | | | | | | | | | | | | | | | | | | While we mostly use the ucidef_set_led_* functions directly in 01_leds we still have the set_wifi_led function in parallel for several old devices. This is not only inconsistent with the other definitions, it also links to the wlan0 interface instead of using a phy trigger which would be independent of the interface name (and is used for all newer devices anyway). Apart from that, the standard names "wifi" and "wifi-led" are not very helpful in a world with different radio bands either. Thus, this patch removes the set_wifi_led function and puts the relevant commands into the cases explicitly. This makes the mechanism used more evident and will hopefully lead to some future improvements or at least prevent some copy-pasting of the old setups. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove option to set WiFi LED via aliasesAdrian Schmutzler2020-10-021-3/+0
| | | | | | | | | | | | | In ramips, it's not common to use an alias for specifying the WiFi LED; actually only one device uses this mechanism (TL-WR841N v14). Particularly since the WiFi LEDs are typically distinguished between 2.4G and 5G etc. it is also not very useful for this target. Thus, this patch removes the setup lines for this mechanism and converts the TL-WR841N v14 to the normal setup. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove model name from LED labelsAdrian Schmutzler2020-10-021-3/+1
| | | | | | | | | | | | | | | | | Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop support for kernel 4.14Adrian Schmutzler2020-09-021-220/+0
| | | | | | | The target seems to be working on 5.4, so drop 4.14 support in preparation for removing it from master entirely. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: switch rt288x subtarget to kernel 5.4Adrian Schmutzler2020-08-071-2/+0
| | | | | | | | | | | | | | The sbutarget has testing support for kernel 5.4 for quite a while and builds fine, however, only one devices there is > 4 MiB. Since it's unlikely to get a Tested-by for that device, and the other ralink subtargets appear to be working with 5.4 so far, let's set this target to 5.4 by default as well. That way, even if the device happens to break, we'll still have at least usable SDK and IB for people to use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-062-2/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: switch rt305x subtarget to kernel 5.4Alexey Dobrovolsky2020-08-051-0/+2
| | | | | | | | | | | | | | RT3x5x seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Since 4 of 6 targets are on kernel 5.4 now, invert the kernel version setup logic in Makefile/target.mk files. Tested on ZyXEL Keenetic. Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [invert version setup logic] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default switch setup in 02_networkChuanhong Guo2020-05-191-3/+0
| | | | | | | | ramips images now relies on explicit switch setup for proper failsafe functionality. Remove default cases where it relies on vlan setup in dts and add switch setup for devices affected. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* Revert "ramips: explicitly disable built-in switch for lan-only devices"Adrian Schmutzler2020-04-281-2/+0
| | | | | | | | | This reverts commit a1693bf626f8cd00363b0b98642b682522dfcf75. The rt288x and rt3883 devices in question don't have switches. Only keep the merged case for rt305x. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: explicitly disable built-in switch for lan-only devicesSungbo Eo2020-04-271-0/+2
| | | | | | | | | Commit 8f6334eb947a ("ramips: explicitly disable built-in switch when needed") did not fix rt288x and rt3883 devices. This patch deals with them. While at it, consolidate duplicate cases in interface setup. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: refresh kernel config for 5.4Chuanhong Guo2020-04-121-37/+44
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: copy kernel config for 5.4Chuanhong Guo2020-04-121-0/+221
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: move and rename out-of-tree mtk eth driverChuanhong Guo2020-04-121-5/+5
| | | | | | | move the driver into shared 'files' directory and rename all symbols from mediatek/mtk to ralink. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: move swconfig to subtargets except for MT7621DENG Qingfang2020-04-041-1/+1
| | | | | | | As MT7621 does not use swconfig anymore, move the package swconfig to other subtargets. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: rt288x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-4/+5
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for ralink,v11st-fe as this device does not set up a MAC address for ethernet in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove default case for MAC address assignmentAdrian Schmutzler2019-11-061-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, MAC address assignment in ramips has contained a default case, which defined wan_mac = eth0 + 1 for _every_ device not having an explicit case there. This is not desirable, as many device supporters will just not care or know about this definition, so another MAC address will be introduced by accident. In some cases the wan_mac is assigned although it is not needed, in other cases even addresses not dedicated to the device will be used (e.g. wan_mac actually is eth0 - 1, but during support nobody cared, so eth0 + 1 is used now, which might actually belong to another device ...). Thus, in this PR the former default case is converted to an explicit case. This one comprises all devices not being accounted for by other cases, reduced by those not having wan at all. The big number of entries for this node might be another indication that many of them wouldn't actually be there if there hadn't been default wan_mac setup. In exchange, the current "do nothing" case can be removed, as it will be the new default case. The devices being put in the newly created explicit case were determined as follows: 1. Create a list of all devices based on the DTS files. 2. Remove all devices already having an explicit entry setting their address. 3. Remove all devices that only have lan set up in the first part of 02_network: mt7620: - alfa-network,tube-e4g - asus,rp-n53 - buffalo,wmr-300 - comfast,cf-wr800n - edimax,ew-7476rpc - edimax,ew-7478ac - elecom,wrh-300cr - hnet,c108 - kimax,u25awf-h1 - kimax,u35wf - kingston,mlw221 - kingston,mlwg2 - microduino,microwrt - netgear,ex2700 - netgear,ex3700 - netgear,wn3000rp-v3 - planex,cs-qr10 - planex,mzk-ex300np - planex,mzk-ex750np - ravpower,wd03 - sercomm,na930 - yukai,bocco - zbtlink,zbt-cpe102 - zte,q7 mt7621: - gnubee,gb-pc1 - gnubee,gb-pc2 - linksys,re6500 - mikrotik,rbm11g - netgear,ex6150 - thunder,timecloud - tplink,re350-v1 - tplink,re650-v1 mt76x8: - alfa-network,awusfree1 - d-team,pbr-d1 - glinet,vixmini - vocore,vocore2-lite - tama,w06 - tplink,tl-mr3020-v3 - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 - vocore,vocore2 - widora,neo-16m - widora,neo-32m rt288x: - buffalo,wli-tx4-ag300n - dlink,dap-1522-a1 rt305x: - allnet,all0256n-4m - allnet,all0256n-8m - allnet,all5002 - allnet,all5003 - alphanetworks,asl26555-16m - alphanetworks,asl26555-8m - asus,wl-330n - aximcom,mr-102n - dlink,dcs-930 - easyacc,wizard-8800 - hame,mpr-a2 - hootoo,ht-tm02 - huawei,d105 - intenso,memory2move - planex,mzk-dp150n - rt305x dlink,dcs-930l-b1 - sparklan,wcr-150gn - tenda,3g150b - tenda,3g300m - tenda,w150m - trendnet,tew-638apb-v2 - unbranded,a5-v11 - vocore,vocore-16m - vocore,vocore-8m - wansview,ncs601w - zorlik,zl5900v2 rt3883: - loewe,wmdr-143n - omnima,hpm 4. Put the remaining devices in the new case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: split base-files into subtargetsAdrian Schmutzler2019-11-033-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space. In certain cases, keeping files in parent (=target) base-files was more convenient, and thus no splitting was performed for those. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (mt7621) 60958 B split (mt7620) 46358 B (- 14.3 kiB) split (mt7621) 48759 B (- 11.9 kiB) split (mt76x8) 44948 B (- 15.6 kiB) split (rt288x) 43508 B (- 17.0 kiB) split (rt305x) 45616 B (- 15.0 kiB) split (rt3883) 44176 B (- 16.4 kiB) Run-tested on: GL.iNet GL-MT300N-V2 (mt76x8) D-Link DWR-116 (mt7620) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: disable CONFIG_MTD_SPLIT_FIRMWAREMathias Kresin2019-01-261-1/+0
| | | | | | | It's no longer needed as all mt7621 devices use DT binding (supported by upstream mtd code) for specifying "firmware" part format explicitly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: only optimized for size if small_flashMathias Kresin2018-07-122-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | Add a new config option to allow to select the default compile optimization level for the kernel. Select the optimization for size by default if the small_flash feature is set. Otherwise "Optimize for performance" is set. Add the small_flash feature flag to all (sub)targets which had the optimization for size in their default kernel config. Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new setting. Exceptions to the above are: - lantiq, where the optimization for size is only required for the xway_legacy subtarget but was set for the whole target - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have plenty of space and an optimization for size doesn't make much sense - rb532, which has 128MByte flash Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: drop linux 4.9 supportFelix Fietkau2018-04-061-210/+0
| | | | | | | 4.14 has been tested a lot by a number of users, and we want to use it for the release. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: optimize for performance by default starting with 4.14Felix Fietkau2018-02-241-0/+2
| | | | | | Keep size optimizations for smaller targets that already switched Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: preliminary support for 4.14Roman Yeryomin2018-02-151-0/+229
| | | | | | | | - removed upstreamed patches - 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed Signed-off-by: Roman Yeryomin <roman@advem.lv> Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for D-Link DAP-1522 A1George Hopkins2018-02-131-0/+1
| | | | | | | | | | | | | | | | | | D-Link DAP-1522 is a wireless bridge/access point with 4 LAN ports and a dual-band wireless chipset. Specifications: - Ralink RT2880 - 32 MB of RAM - 4 MB of Flash - 4x 10/100/1000 Mbps Ethernet (RTL8366SR) - 802.11abgn (RT2850) Flash Instructions: 1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin 2. Open the web interface and upload the image Signed-off-by: George Hopkins <george-hopkins@null.net>
* ramips: drop stray kernel 4.4 configsMathias Kresin2017-07-271-203/+0
| | | | | | | The kernel 4.4 patches where already removed with the bump to 4.9. Drop the the subtarget configs as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: cleanup CONFIG_SCHED_HRTICKStijn Tintel2017-06-292-2/+0
| | | | | | | Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the generic config in b47fd7656336162360ebf66147326763ddae3f8d. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: disable CONFIG_SG_POOL by defaultSergey Ryazanov2017-06-071-1/+0
| | | | | | | | CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last one is disabled by default then disable CONFIG_SG_POOL by default too. And explicitly enable it only for platforms that use CONFIG_SCSI. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: purge default packages on MT7621Daniel Golle2017-05-041-1/+1
| | | | | | | | | | | | | | In order to have a smaller initramfs image remove all packages not needed on all devices and add them explicitely for those actually needing them. Also remove wpad-mini from ramips default package set and add it to all sub-targets except for MT7621. While at it reorder packages alphabetically and replace kmod-mt76 with kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on a specific board. Hopefully fixes FS#758 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add v4.9 supportJohn Crispin2017-02-141-0/+211
| | | | | | NAND support is missing Signed-off-by: John Crispin <john@phrozen.org>
* ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to F5D8235 V1 (rt288x)Tobias Wolf2017-02-021-2/+2
| | | | | | | | | | This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and configures the F5D8235 V1 target to use append-dtb for kernel creation instead of OWRTDTB. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de> [Jo-Philipp Wich: rewrap commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips/rt288x: switch CPU_TYPE to 24kcFelix Fietkau2017-01-241-1/+1
| | | | | | | | | | | While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2 architecture just like the 24Kc, so the instruction set should be 100% compatible. Switching it to 24kc allows it to share the package architecture with a lot of other targets instead of creating a special case, saving buildbot resources. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1Tobias Wolf2016-12-041-0/+8
| | | | | | This router uses an PCI attached NEC EHCI controller to support the single USB port. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288xTobias Wolf2016-12-041-1/+5
| | | | | | This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: fix the number of uarts for each SoCÁlvaro Fernández Rojas2016-06-031-1/+0
| | | | | | | | - Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620. - Allow up to 3 uarts on MT7621 and MT7628. - Remove unneeded SERIAL_8250_RT288X for MT7628. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: convert rt2880 to new image building codeJohn Crispin2016-05-123-48/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: convert the remaining subtargets to 4.4Felix Fietkau2016-03-071-8/+10
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48954
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-27 17:58:03 +0000