aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for Keenetic KN-3010Maxim Anisimov2022-11-201-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT. Specification: - System-On-Chip: MT7621DAT - CPU/Speed: 880 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100/1000 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn - Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac - 4x LED, 2x button, 1x mode switch Notes: - The device supports dual boot mode - The firmware partitions were concatinated into one - The FN button led indicator has been reassigned as the 2.4GHz wifi indicator. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin" to "KN-3010_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: Add support for D-Link DIR-3060 A1Ivaylo Ivanov2022-11-132-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1/ Use the provided emergency web GUI to upload and flash a new firmware to the device Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
* ramips: add support for Rostelecom RT-SF-1Mikhail Zhilkin2022-11-133-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 ZigBee: 3.0, EFR32 MG1B232GG Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Remove dots from the OpenWrt factory image filename 2. Login to the router web interface 3. Update firmware using web interface with the OpenWrt factory image 4. If OpenWrt is booted, then no further steps are required. Enjoy! Otherwise (Stock firmware has booted again) proceed to the next step. 5. Update firmware using web interface with any version of the Stock firmware 6. Update firmware using web interface with the OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+------------+ | use | address | example | +-----+------------+------------+ | LAN | label | *:72, *:d2 | | WAN | label + 11 | *:7d, *:dd | | 2g | label + 2 | *:74, *:d4 | | 5g | label + 3 | *:75, *:d5 | +-----+------------+------------+ The label MAC address was found in Factory 0x21000 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: fix MAC address assignment for rt1800, e7350Arne Zachlod2022-11-131-0/+1
| | | | | | | | previous commit ffa4b5283b introduced a bug which broke the MAC address assignment for belkin,rt1800 and linksys,e7350. Fixes: ffa4b5283b39 ("ramips: add support for Mikrotik LtAP-2HnD") Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ramips: add support for Mikrotik LtAP-2HnDArne Zachlod2022-11-124-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS receiver and two mPCIe slots. Specifications: * SoC: MT7621A * RAM: 128 MiB Nanya NT5CC64M16GP-DI * Flash: 16 MiB winbond W25Q128JV * WLAN: * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas, with RF switches for external connectors) * Ethernet: 1 Gbps, single port * USB Host: USB 2.0 Speeds * Serial: 115200 baud * LEDs: Power, System, GPS, 5* RSSI * mPCIe: * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host) * miniPCIe slot 2: USB 2.0 and 3.0 * SIM Cards: * Slot 1 Connected to mPCIe slot 1 * Slot 2 and 3 connected to mPCIe slot 2 via switch * GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14 gpios are exposed to /sys/class/gpio: * usb-select: swithes USB 2.0 interface between external port and internal mPCIe slot 1 default is the external USB interface * gps-reset: resets the GPS interface chip * sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2 * gps-ant-select: switches GPS antenna between internal antenna and SMA connected antenna * lte-reset: resets mPCIe slot 2 Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ramips: add support for TP-Link MR600 V2(EU)Linos Giannopoulos2022-11-052-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation etc. and can reportedly achieve higher bandwidth with it. - Specifications: * SoC: Mediatek MT7621DAT 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (GD25Q128C) * LTE Modem: Qualcomm MDM9240 * WiFi 5GHz: Mediatek MT7613BEN * WiFi 2.4GHz: Mediatek MT7603EN * Ethernet: MT7530, 4x 1000Base-T. * UART: Serial console (115200 8n1), J1(GND:3) * Buttons: Reset, WPS. * LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2, Signal3 - MAC Addresses: OEM firmware configuration: 54:af:97:xx:xx:7b : 2.4G 54:af:97:xx:xx:7a : 5G 54:af:97:xx:xx:7c : LTE 54:af:97:xx:xx:7b : LAN (label) 54:af:97:xx:xx:7c : WAN - Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to openwrt.img Configure the TFTP server to listen at 192.168.0.5/24. 3. Connect to the serial console. Attach power and interrupt the boot procedure when prompted (type `tpl`). Credentials are admin / 1234 4. Configure U-Boot for booting OpenWrt from ram $ tftpboot $ bootm 5. Transfer the OpenWrt sysupgrade image to the device. - LTE: In order to setup the wwan0 interface: 1. Add a `qmi` proto interface under `/etc/config/network`, e.g.: ``` config interface 'wwan0' option device '/dev/cdc-wdm0' option proto 'qmi' option pincode 'XXXX' option apn 'your_isp_apn' ``` 2. Add `wwan0` interface to the `wan` firewall zone 3. `/etc/init.d/network restart` Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
* ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1Shiji Yang2022-11-053-4/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for YunCore FAP690Volodymyr Puiul2022-10-313-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI NOR - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 1x 1GiE via MT7530 - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Bootloader: U-Boot - Buttons: - SW1 - no label on the box, combined with led - Led: Status. RGB controlled by - GPIO 14 - green color - GPIO 15 - red color - GPIO 16 - blue color Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise it will not boot. MAC addresses as verified by OEM firmware: vendor source LAN factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
* ramips: add support for YunCore FAP640Volodymyr Puiul2022-10-301-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Power: 802.11af/at PoE; - Bootloader: U-Boot - Buttons: - Reset - LEDs: - Status - RGB controlled by - GPIO 14 LOW - green color - GPIO 15 LOW- red color - GPIO 16 LOW - blue color - WAN - gren color, controlled by switch GPIO 12 LOW - LAN1 - gren color, controlled by switch GPIO 9 HIGH - LAN2 - gren color, controlled by switch GPIO 6 LOW - LAN3 - gren color, controlled by switch GPIO 3 LOW - LAN4 - gren color, controlled by switch GPIO 0 LOW Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise router will not boot. MAC addresses with OEM firmware: vendor source lan factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
* kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic configAleksander Jan Bajkowski2022-10-212-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should be enabled on target or subtarget based on SoC architecture. Fixes warning: $ make kernel_oldconfig CONFIG_TARGET=subtarget ... .config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state .... Summary: - ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture. If it is disabled then the processor operates in LITTLE_ENDIAN mode (default), - ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This option should be enabled after OpenWRT moves to kernel 6.x. After refreshing the kernel, the symbol disappears, - ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN, - MIPS - enabled relevant symbols, - POWERPC - enabled CONFIG_CPU_BIG_ENDIAN, - UML - Symbols are not defined for this architecture, - X86 - always little endian. Symbols are not defined for this architecture. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-192-0/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix switch setup for ASUS RT-AX53UMatthias Schiffer2022-10-031-0/+1
| | | | | | | The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface corresponding to the non-existing port. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: move ubnt ledbar driver to a separate packageFelix Fietkau2022-09-302-2/+0
| | | | | | | Simplifies the tree by removing a non-upstream kernel patch and related kconfig symbols Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: update MAC address configuration for Buffalo WSR-1166DHPKazuhiro Ito2022-09-281-2/+2
| | | | | | | | | | | | Convert MAC address and label_mac configuration of Buffalo WSR-1166DHP to use the generic function of OpenWrt. Apply commit 770cfe9 for WCR-1166DS to WSR-1166DHP too. Tested on the device and MAC address is kept before and after this change. Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
* ramips: fix GB-PC1 and GB-PC2 LEDsArınç ÜNAL2022-09-181-3/+1
| | | | | | | | | | | | | | | Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the device schematics. Tests on a GB-PC2 by me and Petr proved otherwise. Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired to GPIO 3 or 4 and the wiring is currently unknown. Set ethyellow-orange to display link state and activity of the ethyellow interface for GB-PC2. Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: 5.15: refresh subtarget kconfigsSungbo Eo2022-09-181-11/+1
| | | | | | Refresh config with `make kernel_oldconfig`. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-113-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
* ramips: add support for Linksys E7350Rosen Penev2022-09-115-2/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Belkin RT1800Rosen Penev2022-09-115-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-291-0/+4
| | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: a0e1d3ab7b4f ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-204-4/+8
| | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: get MAC addr from the encrypted partition (WG4хх223)Mikhail Zhilkin2022-08-192-11/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223 configuration partition (board_data)to get base MAC address from it. As a result, after this change the hack with saving MAC addressees to u-boot-env before installation of OpenWrt is no longer necessary. This is necessary for the following devices: - Beeline Smartbox Flash (Arcadyan WG443223) - MTS WG430223 (Arcadyan WG430223) Example: +----------------+-------------------+------------------------+ | | MTS WG430223 | Beeline Smartbox Flash | +----------------+-------------------+------------------------+ | base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 | | LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 | | WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 | | WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 | +----------------+-------------------+------------------------+ Collected statistic shows that the 2-4th bits of the 7th byte of the WLAN_5g MAC are the constant (see #10062 for more details): - Beeline Smartbox Flash - 100 - MTS WG430223 - 010 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Beeline SmartBox TURBOMikhail Zhilkin2022-08-133-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 Button: 2 buttons (Reset & WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (admin:admin) 2. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where SNxxxxxxxxxx is the serial number from the backplate label) 6. Run in SSH shell: sh 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface (admin:admin) 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- 1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:54 | | WAN | label + 1 | *:55 | | 2g | label + 4 | *:58 | | 5g | label + 5 | *:59 | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Co-developed-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* kernel: Activate CONFIG_GPIOLIB in generic configurationHauke Mehrtens2022-08-102-2/+0
| | | | | | | | All targets expect the malta target already activate the CONFIG_GPIOLIB option. Move it to generic kernel configuration and also activate it for malta. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "nftables: fix parsing date expressions"Jo-Philipp Wich2022-08-091-0/+3
| | | | | | | | This reverts commit eada8925776aafa3ec47d66fb89bf7eae730edf7. The commit contained unrelated target changes. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* nftables: fix parsing date expressionsJo-Philipp Wich2022-08-091-3/+0
| | | | | | | | Musl libc does not support the non-POSIX "%F" format for strptime() so replace all occurrences of it with an equivalent "%Y-%m-%d" format. Fixes: #10419 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for ZyXEL LTE3301-PlusAndré Valentin2022-08-065-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7615E - Switch: 4 LAN ports (Gigabit) - LTE: Quectel EG506 connected by USB3 to SoC - SIM: 1 micro-SIM slot - USB: USB3 port - Buttons: Reset, WPS - LEDs: Multicolour power, internet, LTE, signal, Wifi, USB - Power: 12V, 1.5A The device is built as an indoor ethernet to LTE bridge or router with Wifi. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc MAC assignment: lan: 98:0d:67:ee:85:54 (base, on the device back) wlan: 98:0d:67:ee:85:55 Installation from web GUI: - Log in as "admin" on http://192.168.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - format ubi device: ubiformat /dev/mtd6 - attach ubi device: ubiattach -m6 - create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB - rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB - run sysupgrade with sysupgrade image For more details about flashing see commit 2449a632084b ("ramips: mt7621: Add support for ZyXEL NR7101"). Please note that this commit is needed: firmware-utils: add marcant changes for ZyXEL NBG6716 and LTE3301-PLUS Signed-off-by: André Valentin <avalentin@marcant.net>
* ramips: adding support for Asus RP-AC56Lea Teuberth2022-08-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: CPU: MT7621A dual-core 880MHz RAM: 64MB DDR2 FLASH: 16MB MX25L12805D NOR SPI WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI WIFI: 5GHz 2x2 MT7662 a/b/ac PCI ETH: 1xLAN 1000base-T integrated SWITCH: MT7530 Port 0: LAN, Port 6: CPU LED: Power, 2.4GHz WiFi, 5GHz WiFi BTN: WPS, Reset UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1 MISC: Audio support Installation: 1. Update using recovery mode - while holdig "reset" button, power on the device - keep holding "reset" until power led is flashing yellow - set own IP to 192.168.1.75, subnet mask: 255.255.255.0 - push firmware image (can be factory.bin or sysupgrade.bin) using tftp client in binary mode to 192.168.1.1 Notes: This board has only two MAC addresses programmed in the "factory" partition: - MAC for wlan0 (2.4GHz) at offset 0x0004 - MAC for wlan1 (5GHz) at offset 0x8004 - stock firmware re-uses wlan0 MAC for ethernet - no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006 Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
* ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806Shiji Yang2022-07-313-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | H3C TX180x series WiFi6 routers are customized by different carrier. While these three devices look different, they use the same motherboard inside. Another minor difference comes from the model name definition in the u-boot environment variable. Specifications: SOC: MT7621 + MT7915 ROM: 128 MiB RAM: 256 MiB LED: status *2 Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP server IP: 192.168.124.99 MAC Address: use address(sample 1) address(sample 2) source label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1 wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode) WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode) WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7 WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7 Compatibility mode is used to guarantee the connection of old devices that only support WiFi4 or WiFi5. TFTP + TTL Installation: Although a TTL connection is required for installation, we do not need to tear down it. We can find the TTL port from the cooling hole at the bottom. It is located below LAN3 and the pins are defined as follows: |LAN1|LAN2|LAN3|----|WAN| -------------------- |GND|TX|RX|VCC| 1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in server's root directory, rename it to a simple name "initramfs.bin". 2. Plug in the power supply and wait for power on, connect the TTL cable and open a TTL session, enter "reboot", then enter "Y" to confirm. Finally push "0" to interruput boot while booting. 3. Execute command to install a initramfs system: # tftp 0x80010000 192.168.124.99:initramfs.bin # bootm 0x80010000 4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those partitions if we want to back to stock firmwre due to official website does not provide download link. # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin # dd if=/dev/mtd4 of=/tmp/firmware.bin 5. Edit u-boot env to ensure use default bootargs and first image slot: # fw_setenv bootargs # fw_setenv bootflag 0 6. Upgrade sysupgrade firmware. 7. About restore stock firmware: flash the "firmware" and "u-boot-env" partitions that we backed up in step 4. # mtd write /tmp/u-boot-env.bin u-boot-env # mtd write /tmp/firmware.bin firmware Additional Info: The H3C stock firmware has a 160-byte firmware header that appears to use a non-standard CRC32 verification algorithm. For this part of the data, the u-boot does not check it so we can just directly replace it with a placeholder. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-07-203-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear WAX202Wenli Looi2022-07-194-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ramips: add support for Beeline SmartBox GIGAMikhail Zhilkin2022-07-035-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ASUS RP-AC87Tamas Balogh2022-06-292-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC87 ac2600 Repeater 2.4GHz 800Mbps 5GHz 1733Mbps Hardware specifications: SoC: MT7621A 2 cores 4 threads @880MHz WiFi2G: MT7615E 2G 4x4 b/g/n Wifi5G: MT7615E 5G 4x4 n/ac DRAM: 128MB DDR3 @1200mhz Flash: 16MB MX25L12805D SPI-NOR LAN/WAN: MT7530 1x1000M MAC addresses as verified by OEM firmware: use address source Lan/W5G *:B0 factory 0x8004 (label) W2G *:B4 factory 0x0 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.2 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-06-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-242-0/+4
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: force ZyXEL NR7101 to boot from "Kernel" partitionBjørn Mork2022-06-241-0/+1
| | | | | | | | | | | | | | | | | | | Make sure BootingFlag points to the system partition we install to. The BootingFlag variable selects which system partition the system boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have device specific support for this dual image scheme, and can therefore only boot from "Kernel". This has not been an issue until now, since all known OEM firmware versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0. But the newest OEM firmware has a new upgrade procedure, installing to the "inactive" system partition and setting BootingFlag accordingly. This workaround is needed until the dual image scheme is fully supported. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-133-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-031-0/+4
| | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-162-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-091-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-04-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-04-232-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-04-232-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* ramips: add support for OrayBox X3ARay Wang2022-04-173-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-161-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
* kernel: move some symbols to generic configAleksander Jan Bajkowski2022-04-091-8/+0
| | | | | | | | | | | | | | | | | | | This commit add some enabled symbols to generic config. LTO is only supported by clang compiler and therefore should be disabled in the generic config instead of duplicating this symbol in each target. CONFIG_LTO_NONE do this job. The second group of symbols is enabled by the options available in the generic config and is therefore added here: * CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX, * CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL, * CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET. The other symbols are disabled and should be in the generic config. This commit also removes these symbols from subtargets. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ramips: add linux 5.15 support for mt7621Felix Fietkau2022-03-271-0/+315
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix wifi mac address of HiWiFi series devicesShiji Yang2022-03-261-0/+7
| | | | | | | | | | | | | | | | | | For HiWiFi series devices, label_mac can be read from bdinfo partition, and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's label_mac start with D4:EE) For example: label D4:EE:07:32:84:88 lan D4:EE:07:32:84:88 wan D4:EE:07:32:84:89 wlan2g D4:EE:07:32:84:88 wlan5g D0:EE:07:32:84:88 Tested on HiWiFi HC5661. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-194-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: update WLAN MAC address of JCG Y2Chukun Pan2022-03-131-0/+4
| | | | | | | | MAC addresses on OEM firmware: 04:xx:xx:xx:xx:c8 factory 0x4 wlan2g 06:xx:xx:xx:xx:c8 [not on flash] wlan5g Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-31 03:48:17 +0000