aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-041-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> (cherry picked from commit e38de40f8dd350344407fe5a91e81191f6960804)
* ramips: Cudy X6 fixes / improvementsFelix Baumann2023-04-301-2/+3
| | | | | | | | | | | | | | | | | | | | | | | - Correct WiFi MACs, they didn't match oem firmware - Move nvmem-cells to bdinfo partition and remove &bdinfo reference - Add OEM device model name R13 to SUPPORTED_DEVICES This allows sysupgrading from Cudy's OpenWrt fork without force - Label red_led and use it during failsafe mode and upgrades MAC addresses as verified by OEM firmware: use address source LAN b4:4b:d6:2d:c8:4a label WAN b4:4b:d6:2d:c8:4b label + 1 2g b4:4b:d6:2d:c8:4a label 5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [read wifi mac from flash offset] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 45cf200b2e22c34f2ae043b87e24230de526fefc)
* ramips: add support for D-Link DAP-X1860 A1Sebastian Schaper2023-04-084-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The DAP-X1860 is a wall-plug AX1800 repeater. Specifications: - MT7621, 256 MiB RAM, 128 MiB SPI NAND - MT7915 + MT7975 2x2 802.11ax (DBDC) - Ethernet: 1 port 10/100/1000 - LED RSSI bargraph (2x green, 1x red/orange), status and RSSI LEDs are incorrectly populated red/orange (should be red/green according to documentation) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tar -xvf DAP-X1860_RevA_Firmware_101b94.bin - openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \ -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ== - tar -xvf FWImage.st1 - flash kernel_DAP-X1860.bin via Recovery Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> (cherry picked from commit 3c31f6b521bb5fc49e222a8f2bcd454b73452a0e)
* ramips: add missing LEDs to Asus RT-AX53UMarian Sarcinschi2023-04-021-0/+5
| | | | | | | | | | | | | | | | | This patch adds the missing LEDs to Asus RT-AX53U. Based on PR #10400 and patch provided in #11068 - enable the two LEDs controlled by mt7915e for wireless; - add label to power LED so it works properly and fix formatting; - add the USB LED; - switch LEDs are best left to be controlled by hardware for now. Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com> Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Co-Authored-By: Hartmut Birr <e9hack@gmail.com> Tested-by: Felix Baumann <felix.bau@gmx.de> Tested-by: Marian Sarcinschi <znevna@gmail.com> Signed-off-by: Marian Sarcinschi <znevna@gmail.com> (cherry picked from commit c4b806d5c4ccc653968620e6e9aec93bc4e370e5)
* ramips: fix 5g mac for TOTOLINK X5000RChuanhong Guo2023-03-271-0/+4
| | | | | | | | | | There's no valid mac address for the second band in the eeprom. The vendor fw uses 2.4G mac + 4 as the mac for 5G radio. Do the same in our firmware. Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R") Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 212632540043cc9b911c2efb86156479f2710836)
* ramips: add support for Mercusys MR70XDavid Bauer2023-03-241-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: Winbond W25Q128JV (SPI-NOR 16MB) - WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC) - UART: >TX RX GND 3v3 (115200 8N1, J1) Do not connect 3v3. TX is marked with an arrow. Installation ============ Flash factory image. This can be done using stock web ui. Revert to stock firmware ======================== Flash stock firmware via OEM Web UI Recovery mode. Web UI Recovery method ====================== 1. Unplug the router 2. Plug in and hold reset button 5~10 secs 3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0 4. Flash image with web browser to 192.168.1.1 Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 47de2c686291e69afc9f443e27e1dfd11ed5fbe7)
* ramips: fix Archer AX23 WiFi MAC address conflictDavid Bauer2023-03-211-4/+1
| | | | | | | | | | | The original claim about conflicting MAC addresses is wrong. mac80211 does increment the first octet and sets the LA bit. This means our "workaround" actually leads to the issue while incrementing the last octet is safe. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit d52870125d57d39e73e6c305dd36fad44fe4a773)
* ramips: add support for TP-Link Archer AX23 v1David Bauer2023-03-212-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR () WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Upload the factory image using the Web-UI. Web-Recovery ------------ The router supports a HTTP recovery mode by holding the reset-button when powering on. The interface is reachable at 192.168.0.1 and supports installation using the factory image. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 7dceef5ee554ec4ab5d2dd2ff999f4a60bf2e0f4)
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit dce66899bf243d78689afcc693340b891bbf4c2d)
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-271-0/+1
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 711f1a8bcbdde1ee9e2934d707fb1765fc644268)
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-10-143-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit a0b7fef0ffe4cd9cca39a652a37e4f3ce8f0a681)
* ramips: fix switch setup for ASUS RT-AX53UMatthias Schiffer2022-10-031-0/+1
| | | | | | | | The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface corresponding to the non-existing port. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 149fc3a269b435483b31df03d6fd9679286cf9e7)
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-182-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net> (cherry picked from commit 820f0c07c544652c1c53a45262a481ac5dbe139b)
* ramips: fix GB-PC1 and GB-PC2 LEDsArınç ÜNAL2022-09-181-3/+1
| | | | | | | | | | | | | | | | Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the device schematics. Tests on a GB-PC2 by me and Petr proved otherwise. Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired to GPIO 3 or 4 and the wiring is currently unknown. Set ethyellow-orange to display link state and activity of the ethyellow interface for GB-PC2. Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 2a6ef7f53d7b96e4ee0200196c28ed6b0a7c8465)
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-291-0/+4
| | | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: 158a5af80102d ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 7bee10a7d2d16251113147c28dd4548af5c14bab)
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-263-4/+7
| | | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 4807bd6a00bcf44dd821047db76a2a799f403cd4)
* ramips: get MAC addr from the encrypted partition (WG4хх223)Mikhail Zhilkin2022-08-192-11/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223 configuration partition (board_data)to get base MAC address from it. As a result, after this change the hack with saving MAC addressees to u-boot-env before installation of OpenWrt is no longer necessary. This is necessary for the following devices: - Beeline Smartbox Flash (Arcadyan WG443223) - MTS WG430223 (Arcadyan WG430223) Example: +----------------+-------------------+------------------------+ | | MTS WG430223 | Beeline Smartbox Flash | +----------------+-------------------+------------------------+ | base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 | | LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 | | WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 | | WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 | | WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 | +----------------+-------------------+------------------------+ Collected statistic shows that the 2-4th bits of the 7th byte of the WLAN_5g MAC are the constant (see #10062 for more details): - Beeline Smartbox Flash - 100 - MTS WG430223 - 010 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit a6b0d0806055a53a2538df83f8322c38ee9f3441)
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-08-163-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 498c15376bae109bfe130cc5581f83e4cc52c0f9)
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-08-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 8c00fd9b4519bf0ef8fb3470a6df421b9f38c03c)
* ramips: add support for Netgear WAX202Wenli Looi2022-07-214-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0f068e7c4a83bcbf20c4e52a5f8a3f1fe2af2246)
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-271-0/+2
| | | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 539e60539a2fde6531bd179c94bb9c7f8f490f2b)
* ramips: force ZyXEL NR7101 to boot from "Kernel" partitionBjørn Mork2022-06-251-0/+1
| | | | | | | | | | | | | | | | | | | | Make sure BootingFlag points to the system partition we install to. The BootingFlag variable selects which system partition the system boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have device specific support for this dual image scheme, and can therefore only boot from "Kernel". This has not been an issue until now, since all known OEM firmware versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0. But the newest OEM firmware has a new upgrade procedure, installing to the "inactive" system partition and setting BootingFlag accordingly. This workaround is needed until the dual image scheme is fully supported. Signed-off-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 79112e7d4758cc79dea506ffebdf40e00d94fa06)
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-061-0/+4
| | | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> (cherry picked from commit ce90ba1f3168e3f4581fd8581e2c0cd31efa14cf)
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-171-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4a8eaa5c7c9235212c4af022c18b2dfbadfe557f)
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-172-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 9ee6ac00c43cc253ac554495edb6214563ab1f31)
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-05-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit 32e6942d72b6426d65eaa4dc7f2ba949b3c32985)
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-05-172-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com> (cherry picked from commit 39799974a372fb4333d21f077c670b8a56b9d696)
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-05-172-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea)
* ramips: add support for OrayBox X3ARay Wang2022-04-193-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com> (cherry picked from commit 9a750aae62de74b488d7df7bdbfa78cd606a8aaf)
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-191-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* ramips: add support for Beeline SmartBox FlashMikhail Zhilkin2022-03-194-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Winbond W632GU6NB Flash: 128 MiB (NAND), Winbond W29N01HVSINF Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: 1xUSB3.0 Button: 1 (Reset/WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WE42022 Installation ------------ 1. Place *factory.trx on any web server (192.168.1.2 in this example) 2. Connect to the router using telnet shell (no password required) 3. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 4. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 5. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 6. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 reboot Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | 30:xx:xx:51:xx:09 | No MACs was | | LAN | 30:xx:xx:51:xx:09 | found on Flash | | WAN | 30:xx:xx:51:xx:06 | [1] | | WLAN_2g | 30:xx:xx:51:xx:07 | | | WLAN_5g | 32:xx:xx:41:xx:07 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several Smartbox Flash devices even within the same broadcast domain. Stock firmware image format --------------------------- +--------------+---------------+----------------------------------------+ | Offset | 1.0.15 | Description | +==============+===============+========================================+ | 0x0 | 5d 43 6f 74 | TRX magic "]Cot" | +--------------+---------------+----------------------------------------+ | 0x4 | 00 70 ff 00 | Length (reverse) | +--------------+---------------+----------------------------------------+ | | | htonl(~crc) from 0xc ("flag_version") | | 0x8 | 72 b3 93 16 | to "Length" | +--------------+---------------+----------------------------------------+ | 0xc | 00 00 01 00 | Flags | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of Kernel partition | | 0x10 | 1c 00 00 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | | | Offset (reverse) of RootFS partition | | 0x14 | 00 00 42 00 | from the start of the header | +--------------+---------------+----------------------------------------+ | 0x18 | 00 00 00 00 | Zeroes | +--------------+---------------+----------------------------------------+ | 0x1c | 27 05 19 56 … | Kernel data + zero padding | +--------------+---------------+----------------------------------------+ | | | RootFS data (starting with "hsqs") + | | 0x420000 | 68 73 71 73 … | zero padding to "Length" | +--------------+---------------+----------------------------------------+ | | | Some signature data (format is | | | | unknown). Necessary for the fw | | "Lenght" | 00 00 00 00 … | update via oem fw web interface. | +--------------+---------------+----------------------------------------+ | "Lenght" + | | TRX magic "HDR0". U-Boot is | | 0x10c | 48 44 52 30 | checking it at every boot. | +--------------+---------------+----------------------------------------+ | | | 1.00: | | | | Zero padding to ("Lenght" + 0x23000) | | | | 1.0.12: | | | | Zero padding to ("Lenght" + 0x2a000) | | "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: | | 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: update WLAN MAC address of JCG Y2Chukun Pan2022-03-131-0/+4
| | | | | | | | MAC addresses on OEM firmware: 04:xx:xx:xx:xx:c8 factory 0x4 wlan2g 06:xx:xx:xx:xx:c8 [not on flash] wlan5g Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: update WLAN MAC address of Phicomm K2PChukun Pan2022-03-131-1/+2
| | | | | | | The wireless mac address difference of this machine is similar to that of D-Link DIR-853-R1, so use the same practice. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: mt7621: add support for Zbtlink ZBT-WG1608Kim Namu2022-03-091-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim Namu <namu@theseed.io>
* ramips: add support for Renkforce WS-WN530HP3-ABirger Koblitz2022-03-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Renkforce WS-WN530HP3-A ceiling- mountable Wireless Access Point, which is powered over PoE. Hardware: - SoC: Mediatek MT7621DAT - RAM: 128MiB on SoC - Flash: 16MiB GigaDevice GD25Q128C - 2.4Ghz Wifi: Mediatek MT603EN - 5GHz Wifi: MT613BEN - Ethernet: - 1x 1GBit WAN port, passive PoE capable - 2x 1GBit LAN ports LEDs: 1x Bi-Color LED (red/blue) Buttons: 1x Reset Button, 1x Power Button Installation: Power on the access point and immedately press the reset button for 10 seconds. Connect web-browser to 192.168.10.1 and upload sysupgrade image. Flash uploaded image and wait about 2 minutes for reboot. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
* ramips: Add support for TP-Link TL-WPA8631P v3Joe Mullally2022-03-062-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender Specifications -------------- * SoC: MediaTek MT7621AT * CPU: 880 MHz MIPS 1004KEc dual-core CPU * RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E) * Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG) * Ethernet: SoC built-in Switch 5x 1GbE * Port 0: PLC (connected through AR8035-A) * Port 1-3: LAN * WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN) * PLC: HomePlug AV2 (Qualcomm QCA7500) * PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG) * Buttons: Reset, LED, Pair, Wi-Fi * LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green), 5G (green) * UART: J1 (57600 baud) * Pinout: (3V3) (GND) (RX) (TX) * Visually identify GND from connection to PCB ground plane Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please first check the OpenWRT Wiki page for confirmation that your OEM firmware version is supported. Signed-off-by: Joe Mullally <jwmullally@gmail.com>
* ramips: support TP-Link EAP615-WallStijn Tintel2022-02-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP. The device is very similar to the TP-Link EAP235-Wall. Hardware: * SoC: MediaTek MT7621AT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Ethernet: 4x GbE * Back: ETH0 (PoE-PD) * Bottom: ETH1, ETH2, ETH3 (PoE passthrough) * WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R * LEDS: 1x white * Buttons: 1x LED, 1x reset Stock firmware uses a random MAC address for ethernet. OpenWrt uses the MAC address that is on the device label for ethernet and the wireless interfaces. MAC address must not be incremented, as this will cause MAC address conflicts in case you have two devices with consecutive MAC addresses. Instead, different locally administered addresses will be generated automatically, based on the MAC on the label. Installation via stock firmware: * Enable SSH in the TP-Link web interface * SSH to the device * Run `cliclientd stopcs` * Upload the OpenWrt factory image via the TP-Link web interface Installation via bootloader: * Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1 closest to ETH1. Baud rate 115200 * Interrupt boot process by holding a key during boot * Boot the OpenWrt initramfs: # tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin # bootm * Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin to /tmp and use sysupgrade to install it Thanks to Sander Vanheule for his work on the EAP235-Wall, which made adding support for the EAP615-Wall very easy. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Sander Vanheule <sander@svanheule.net> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for ipTIME A3002MESHYoonji Park2022-02-202-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for ipTIME A3002MESH. Hardware: - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: XMC XM25QH128AHIG (SPI-NOR 16MB) - WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in) - UART: [GND, RX, TX, 3.3V] (57600 8N1, J4) MAC addresses: | interface | MAC | source | comment |-----------|-------------------|----------------|---------- | LAN | 70:XX:XX:5X:XX:X3 | | | WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 | | WLAN 2G | 72:XX:XX:4X:XX:X0 | | | WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4 | | | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown | | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown - WLAN 2G MAC address is not the same as stock firmware since OpenWrt uses LAN MAC address with local bit sets. Installation: 1. Flash initramfs image. This can be done using stock web ui or TFTP 2. Connect to OpenWrt with an SSH connection to 192.168.1.1 3. Perform sysupgrade with sysupgrade image Revert to stock firmware: - Flash stock firmware via OEM TFTP Recovery mode - Perform sysupgrade with stock image TFTP Recovery method: 1. Unplug the router 2. Hold the reset button and plug in 3. Release when the power LED stops flashing and go off 4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0 5. Flash image with TFTP client to 192.168.0.1 Signed-off-by: Yoonji Park <koreapyj@dcmys.kr> [wrap/rephrase commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: update WLAN MAC address of ipTIME A3004TSungbo Eo2022-02-111-0/+6
| | | | | | | | | | | | | | | | Reported MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 90:xx:xx:18:xx:1F | | [1] | WAN | 90:xx:xx:18:xx:1D | | | WLAN 2G | 92:xx:xx:48:xx:1C | | | WLAN 5G | 90:xx:xx:18:xx:1C | factory 0x4 | | | 90:xx:xx:18:xx:1C | config ethaddr | [1] Used in this patch as WLAN 2G MAC address with the local bit set Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-02-112-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC addresses: | interface | MAC address | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:xx:xx:00:xx:9B | | [1] | WAN | 58:xx:xx:00:xx:99 | | | WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 | | WLAN 5G | 5A:xx:xx:40:xx:98 | | | | 58:xx:xx:00:xx:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load addresses: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. The stock web interface will flash only on the inactive boot partition, but the recovery web page will always flash on boot partition 1. Installation via recovery mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-091-0/+1
| | | | | | | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531. Fix some link up/down issues. The errornous check for the PHY mode which broke things with MT7531 has been removed as suggested by patch net: phy: mediatek: remove PHY mode check on MT7531 As a result, things are working fine now on MT7622+MT7531 as well. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for Xiaomi Mi Router CR660x seriesRaymond Wang2022-02-073-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports. Alongside the general model, it has three carrier customized models: CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom) Specifications: - SoC: MediaTek MT7621AT - RAM: 256MB DDR3 (ESMT M15T2G16128A) - Flash: 128MB NAND (ESMT F59L1G81MB) - Ethernet: 1000Base-T x4 (MT7530 SoC) - WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN) - LEDs: System (Blue, Yellow), Internet (Blue, Yellow) - Buttons: Reset, WPS - UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1) - Power: 12VDC, 1A Jailbreak Notes: 1. Get shell access. 1.1. Get yourself a wireless router that runs OpenWrt already. 1.2. On the OpenWrt router: 1.2.1. Access its console. 1.2.2. Create and edit /usr/lib/lua/luci/controller/admin/xqsystem.lua with the following code (exclude backquotes and line no.): ``` 1 module("luci.controller.admin.xqsystem", package.seeall) 2 3 function index() 4 local page = node("api") 5 page.target = firstchild() 6 page.title = ("") 7 page.order = 100 8 page.index = true 9 page = node("api","xqsystem") 10 page.target = firstchild() 11 page.title = ("") 12 page.order = 100 13 page.index = true 14 entry({"api", "xqsystem", "token"}, call("getToken"), (""), 103, 0x08) 15 end 16 17 local LuciHttp = require("luci.http") 18 19 function getToken() 20 local result = {} 21 result["code"] = 0 22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i 's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop bear start;" 23 LuciHttp.write_json(result) 24 end ``` 1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token It should give you a respond like this: {"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."} If so, continue; Otherwise, check the file, reboot the rout- er, try again. 1.2.4. Set wireless network interface's IP to 169.254.31.1, turn off DHCP of wireless interface's zone. 1.2.5. Connect to the router wirelessly, manually set your access device's IP to 169.254.31.3, make sure http://169.254.31.1/cgi-bin/luci/api/xqsystem/token still have a similar result as 1.2.3 shows. 1.3. On the Xiaomi CR660x: 1.3.1. Login to the web interface. Your would be directed to a page with URL like this: http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r- outer 1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME} {PASSWORD} be your OpenWrt router's SSID and password: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy- stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO- RD} It should return 0. 1.3.3. Browse this URL with {STOK} from 1.3.1: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy- stem/oneclick_get_remote_token?username=xxx&password=xxx&- nonce=xxx 1.4. Before rebooting, you can now access your CR660x via SSH. For CR6606, you can calculate your root password by this project: https://github.com/wfjsw/xiaoqiang-root-password, or at https://www.oxygen7.cn/miwifi. The root password for carrier-specific models should be the admi- nistration password or the default login password on the label. It is also feasible to change the root password at the same time by modifying the script from step 1.2.2. You can treat OpenWrt Router however you like from this point as long as you don't mind go through this again if you have to expl- oit it again. If you do have to and left your OpenWrt router unt- ouched, start from 1.3. 2. There's no official binary firmware available, and if you lose the content of your flash, no one except Xiaomi can help you. Dump these partitions in case you need them: "Bootloader" "Nvram" "Bdata" "crash" "crash_log" "firmware" "firmware1" "overlay" "obr" Find the corespond block device from /proc/mtd Read from read-only block device to avoid misoperation. It's recommended to use /tmp/syslogbackup/ as destination, since files would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP Keep an eye on memory usage though. 3. Since UART access is locked ootb, you should get UART access by modify uboot env. Otherwise, your router may become bricked. Excute these in stock firmware shell: a. nvram set boot_wait=on b. nvram set bootdelay=3 c. nvram commit Or in OpenWrt: a. opkg update && opkg install kmod-mtd-rw b. insmod mtd-rw i_want_a_brick=1 c. fw_setenv boot_wait on d. fw_setenv bootdelay 3 e. rmmod mtd-rw Migrate to OpenWrt: 1. Transfer squashfs-firmware.bin to the router. 2. nvram set flag_try_sys1_failed=0 3. nvram set flag_try_sys2_failed=1 4. nvram commit 5. mtd -r write /path/to/image/squashfs-firmware.bin firmware Additional Info: 1. CR660x series routers has a different nand layout compared to other Xiaomi nand devices. 2. This router has a relatively fresh uboot (2018.09) compared to other Xiaomi devices, and it is capable of booting fit image firmware. Unfortunately, no successful attempt of booting OpenWrt fit image were made so far. The cause is still yet to be known. For now, we use legacy image instead. Signed-off-by: Raymond Wang <infiwang@pm.me>
* Revert "kernel: backport MediaTek Ethernet PHY driver"Hauke Mehrtens2022-02-051-1/+0
| | | | | | | | | | | | | | | | | | This reverts commit 8b4cba53a9402f44da2dced4a78ca065b15dca94. This broke the mt7530 on Linksys e8450 (mt7622) for me. [ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL [ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0 [ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL [ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1 [ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL [ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2 [ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL [ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3 [ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL [ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-051-0/+1
| | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530. Fix some link up/down issues. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* Revert "ramips: add support for ipTIME AX2004M"Stijn Tintel2022-02-012-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit f4a79148f8cb ("ramips: add support for ipTIME AX2004M") seems to leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no longer boot. The leak is visible in u-boot: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0x840000e4 Data Size: 10750165 Bytes = 10.3 MiB Architecture: MIPS OS: Linux Load Address: 0x82000000 Entry Point: 0x82000000 Normally, it should look like this: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0xbfca00e4 Data Size: 2652547 Bytes = 2.5 MiB Architecture: MIPS OS: Linux Load Address: 0x80001000 Entry Point: 0x80001000 Revert the commit to avoid more people soft-bricking their devices. This reverts commit f4a79148f8cbb7dfbcddfb0c1128caec45a01596. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-01-292-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specification: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC address: | interface | MAC | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:XX:XX:00:XX:9B | | [1] | WAN | 58:XX:XX:00:XX:99 | | | WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4 | | WLAN 5G | 5A:XX:XX:40:XX:98 | | | | | | | | 58:XX:XX:00:XX:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load address: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation via **recovery** mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: enable I2C_CHARDEV in mt7621/config-5.10Stijn Tintel2022-01-281-0/+1
| | | | | | | | I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the 5.10 config, as it's required for PoE control on Unifi Switch Flex. Fixes: b4aad29a1d7a ("ramips: add support for kernel 5.10") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: update Tenbay T-MB5EU wireless MAC addressDavid Bauer2022-01-221-2/+1
| | | | | | | | | | | | | | The current MAC address assignment is still incorrect. Use the same MAC address as seen on the stock firmware for both wireless interfaces. The 5GHz MAC address OUI is +2 in the first EUI octet. We currently don't do this in OpenWrt. Ignore this offset for now. With the current assignment, recurring MAC addresses between radios is already taken care of. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: enable badblock table support on linksys ea7xxx devicesFelix Fietkau2022-01-131-0/+1
| | | | | | Use remapping only on the kernel partitions. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mikrotik: enable variable size eraseOskari Lemmela2022-01-131-0/+1
| | | | | | | Add support for variable size erase blocks. Enable it to all targets which has mikrotik targets. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-13 21:51:07 +0000