aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/image/mt7628.mk
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for VoCore2Andrew Yong2017-01-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: Add support for Wavlink WL-WN575A3Roger Pueyo Centelles2016-11-081-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug wireless router with the following specifications: - CPU: MediaTek MT7628AN 580MHz - Flash: 8MB - RAM: 64MB - Ethernet: 2x 10/100 Mbps (switched) - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm - Antennas: 4x external (2 per radio), non-detachable - LEDs: 4 programmable + LAN, WAN, POWER - Buttons: reset, WPS Flashing instructions: Factory U-boot launches a TFTP client if WPS button is pressed during power-on. Rename the sysupgrade file and configure a TFTP as follows: - Client (WL-WN575A3) IP: 192.168.10.101 - Server IP: 192.168.10.100 - Filename: firmware.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-4/+4
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: set blocksize for 4MB devicesMathias Kresin2016-09-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Set the blocksize for devices having only 4MB of flash for ramips devices already using the new image build code. Informations about the used flash chip are gathered from the OpenWrt wiki, wikidevi, forums, OEM bootlogs or the compatible property in the device tree source file. The en25q32b from the AirLive Air3GII does not have 4k support in the kernel. For the following boards no information about the used flash chip could be found and a 64k blocksize is assumed: - Ralink V11ST-FE - Ralink AP-RT3052-V22RW-2X2 - MediaTek MT7628 EVB - MediaTek MT7621 EVB - UPVEL UR-326N4G - Buffalo WZR-AGL300NH Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: don't set the same max image size twiceMathias Kresin2016-09-041-2/+0
| | | | | | The ralink_default_fw_size_8M is already set for the default device. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Mercury MAC1200R v2Daniel Golle2016-09-091-0/+7
| | | | | | | | MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM reset button GPIO is still missing (anyone?) bootloader password is 'slp' Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for DuZun DM06Michael Lee2016-06-131-0/+8
| | | | | | | | DuZun DM06 is a develop board based on mt7628 64M RAM, 8M SPI Flash, 1 WAN, 1 LAN. wm8960 codec with line out, line in and speaker output. Signed-off-by: Michael Lee <igvtee@gmail.com>
* ramips: convert mt7628 to new image building codeJohn Crispin2016-05-121-9/+19
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: move different subtarget image generation to separate makefiles to ↵John Crispin2016-04-011-0/+17
improve maintainability - all subtarget specific defines are in their own files - common defines left in main Makefile - each subtarget makefile idefed with SUBTARGET - all subtargets compile tested - few seems to be broken/unneeded things marked with FIXME Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49104