aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for the VoCore2 LiteL. D. Pinney2017-08-113-50/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VoCore2 Lite uses the same PCB as the Vocore2. This patch moves the common VoCore2 parts into dtsi. Removed memory node in the device tree source file. Memory is detected automatically. http://vocore.io/ http://vonger.net/ http://vonger.cn/ Specifications: - SoC: MediaTek MT7688AN - RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H - Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG - Wireless: Built into MT7688AN with onboard IPEX connector Firmware installation: - VoCore2-Lite ships with firmware forked from OpenWrt. - Installation from the bootloader is recommended. - If using luci/sysupgrade use the -n option (do not keep settings) original firmware uses a modified proprietary MediaTek wireless driver. - The wireless is disabled by default in LEDE. - If reverting to factory firmware using the bootloader is recommended. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Tested by: Noble Pepper <noblepepper@gmail.com>
* ramips: fix WHR-1166D WAN portMathias Kresin2017-08-111-1/+1
| | | | | | | | | | | | By adding the ICPlus IP1001 phy driver an already set RGMII delay mode is reset during driver load. Set the rgmii rx delay to fix corrupt/no packages in case the WAN port negotiates to 1000MBit. Fixes: FS#670 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: ArcherC50v1: fix wlan2g MAC addressThibaut VARENE2017-08-061-0/+2
| | | | | | | | | | By default the wlan eprom contains the generic ralink MAC which is not the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses are decremented from the ethernet MAC. This patch fixes the MAC address for wlan2g in line with OFW. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: move common parts into dtsiMathias Kresin2017-08-0315-690/+379
| | | | | | | Move the common parts of boards with multiple flash size variants into dtsi files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: update device tree source filesL. D. Pinney2017-08-03212-1103/+1343
| | | | | | | | Use the GPIO dt-bindings macros and add compatible strings in the ramips device tree source files. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for Netgear EX3800Thibaut VARENE2017-08-031-1/+1
| | | | | | | | | | | | The Netgear EX3800 is essentially an EX3700 with a mains output socket. Both devices use the exact same firmware image (original firmware is named EX3700-EX3800-version.chk). This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and updating the necessary glue. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: cleanup AsiaRF AWM002 eval board supportMathias Kresin2017-08-036-160/+128
| | | | | | | | | | | Cleanup the dtsi files and remove one layer of dtsi. Set the size of the firmware partition to a value matching the flash size from the board (variant) name. Remove the usb led trigger. There is neither a default config for the usb led trigger nor a LED for usb activity indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop AsiaRF AWM003 eval boardMathias Kresin2017-08-031-65/+0
| | | | | | | Everything is identical to the AWM002 8m eval board. No need to duplicate it once more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop Edimax BR-6425 supportMathias Kresin2017-08-031-73/+0
| | | | | | Code to build an image for the Edimax BR-6425 never existed. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add missing partitionsMathias Kresin2017-08-032-9/+57
| | | | | | The partitions were lost during migration to device tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Archer C50v1: fix power ledThibaut VARENE2017-07-291-0/+1
| | | | | | | | | | 01_leds had a workaround for the power led to compensate for the inverted GPIO state. This patch was missing from my previous commit. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> [add the power led default-state which was omitted in the last commit by me] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Archer C50v1: fix LEDs active levelsThibaut VARENE2017-07-291-2/+2
| | | | | | | | | | All LEDs GPIOs are active low on this device. WAN and POWER states were inverted. Add default state for power. Tested on Archer C50v1. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: mt7621: add compatible stringsL. D. Pinney2017-07-2925-0/+27
| | | | | | | Add compatible strings to all mt7621 based device tree source files to fix formal issues. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* ramips: add support for Loewe WMDR-143NOliver Fleischmann2017-07-271-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The WMDR-143N is a small module originally used as a Wifi client in some Loewe smart TV sets. It is sold cheaply at german surplus shops. The module contains a RT3662 SOC. Specifications: - 500 MHz CPU Clock - 1x 10/100Mbps Ethernet (pin header) - 32 MB of RAM - 8 MB of FLASH - 2T3R 2.4/5 GHz (SOC internal) - 3 Antennas on PCB - UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX and RX are 3,3V only! The square hole is pin 1 - Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND) The square hole is pin 1 The original firmware has two identical kernel/rootfs images and two "Factory" calibration data blocks in flash. The LEDE image leaves only the first "Factory" block in place and uses both "Kernel" blocks and the redundant "Factory" block together to gain enough space for the jffs2 partition. Flash instructions: You need UART and Ethernet connections to flash the board. Use the LEDE "sysupgrade.bin" image with tftp. Apply power to the board and in the first 5 seconds, hit 2 to select TFTP upload. The bootloader asks for board- and server IP addresses and filename. Alternate method: With the vendor firmware running, assign an IP address to the ethernet port, tftp the firmware image to /tmp and write to mtd4 ("KernelA"). Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de> [remove pinctrl node from dts, no pin is used as GPIO] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ralink: fix rcu_sched stalls on mt7621John Crispin2017-07-261-0/+13
| | | | | | | | there were 2 bugs *) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize *) HPT frequency was not set making r4k timers not come up properly Signed-off-by: John Crispin <john@phrozen.org>
* ramips: add support for the GnuBee Personal Cloud OneL. D. Pinney2017-07-251-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 2.5" Drives - One micro SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: 1 x WAN and 1 x LAN - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Four GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud One ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use switchdev led trigger, all interfaces are in vlan1; rename leds according to board.d setting; remove ge2 group from the pinmux, this group doesn't exist in the driver] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix wps button gpio for DWR-512Giuseppe Lippolis2017-07-251-1/+1
| | | | | | The WPS button is at GPIO#7. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* ramips: DTS: VoCore2 improvements/fixesPaul Wassi2017-07-251-22/+3
| | | | | | | | | | | The VoCore2 features 128MB of RAM, therefore set memory in DTS to 128*1024*1024 = 0x8000000 The board's LED is connected to GND, set it to ACTIVE_HIGH here. Make serial console working again on kernel 4.9 by change of pinmux configuration. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: add support for TP-Link RE350Alex Maclean2017-07-251-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link RE350 is a wall-wart AC1200 range extender/access point with a single gigabit ethernet port and two non-detachable antennas, based on the MT7621A SoC with MT7603E and MT7612E radios. Firmware wise it is very similar to the QCA based RE450. SoC: MediaTek MT7621A (880MHz) Flash: 8MiB (Winbond W25Q64) RAM: 64MiB (DDR2) Ethernet: 1x 1Gbit Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E) LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act (green) Buttons: On/off, LED, reset, WPS Serial header at J1, 57600 8n1: Pin 1 TX Pin 2 RX Pin 3 GND Pin 4 3.3V Factory image can be uploaded directly through the stock UI. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for Phicomm K2PChuanhong Guo2017-07-201-0/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It uses one MT7615D radio chip with DBDC mode enabled. This mode allows this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the same time. However mt76 doesn't support it currently so there is no wireless available. Specification: - SoC: MediaTek MT7621AT - Flash: 16 MB - RAM: 128 MB - Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps) - Wireless radio: MT7615D on PCIE0 - UART: 1 x UART on PCB - 57600 8N1 Issue: - Wireless radio doesn't work due to the lack of driver. Flash instruction: Using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2,then follow the instruction to set device and tftp server IP address and input the firmware file name.U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix GL-inet GL-MT300N-V2 WAN/LAN MAC addressJohn Marrett2017-07-151-1/+1
| | | | | | | | | | | | | | Correct MAC address lookup to appropriate offset based on vendor source. Override the WAN MAC to use the same address as LAN. The switch driver increments the base MAC address for the WAN vlan but the stock firmware uses the same MAC address for all interfaces. Based on vendor source commit https://github.com/domino-team/lede-1701/commit/efb0518 Signed-off-by: John Marrett <johnf@zioncluster.ca>
* ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13Piotr Dymacz2017-06-293-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with 5-port FE switch and non-detachable antennas. Both are very similar and are based on MediaTek MT7628NN (aka MT7628N) WiSoC. The difference between these two models is in number of available LEDs, buttons and power input switch. This work is partially based on GitHub PR#974. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - TL-WR840N v4: 5x LED (GPIO-controlled), 1x button - TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device ("0x4"/"0x13" for these devices) but it seems that anything other than "0" is correct. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. Tests showed that the GUI upgrade routine copies value of "Additional Hardware Version" from existing firmware into offset "0x2023c" in provided file, _before_ storing it in flash. In case of vendor firmware upgrade files (which all include U-Boot image and two headers), this offset points to the matching field in kernel+rootfs firmware part header. Unfortunately, in case of LEDE factory image file which contains only one header, it points to the offset "0x2023c" in kernel image. This leads to a corrupted kernel and ends up with a "soft-bricked" device. The good news is that U-Boot in these devices contains well known tftp recovery mode, which can be triggered with "reset" button. What's more, in comparison to some of older MediaTek based TP-Link devices, this recovery mode doesn't write whole file at offset "0x0" in flash, without verifying provided file in advance. In case of recovery mode in these devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes from rest of the file are stored in flash at offset "0x20000". Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. To access U-Boot CLI, keep pressed "4" key during boot. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for TRENDnet TEW-638APB V2Pavlo Samko2017-06-171-0/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for the TRENDnet TEW-638APB V2. Specification: - SoC: Ralink SoC RT3052F - Flash: 4MB - RAM: 32MB - Ethernet: 1x LAN (100 Mbps) - Wireless: 2.4GHz b/g/n, 2x external antenna - Buttons: 1x Reset, 1x WPS - LEDs: Power (green), Ethernet (green), WPS (green and orange), Wireless (green) - UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1 Installation via vendor firmware: - upload sysupgrade.bin image via TFTP: - stop uboot into tftp-load into option "2" - upload sysupgrade.bin image Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
* ramips: fix Phicomm K1S(PSG1208) pinmux小桥2017-06-121-1/+1
| | | | | | Use gpio function for pins with LEDs. Signed-off-by: 小桥 <29551030@qq.com>
* ramips: add support for Ubiquiti EdgeRouter X-SFPSven Roederer2017-06-073-102/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves support for the EdgeRouter X (PoE-passthrough). Specification: - SoC: MediaTek MT7621AT - Flash: 256 MiB - RAM: 265 MiB - Ethernet: 5 x LAN (1000 Mbps) - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1 - EdgeRouter X: - 1 x PoE-Passtrough (Eth4) - powered by Wallwart or passive PoE - EdgeRouter X-SFP: - 5 x PoE-Out (24V, passive) - 1 x SFP (unknown status) - powered by Wallwart (24V) Doesn't work: * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. Installation via vendor firmware: - build an Initrd-image (> 3MiB) and upload the factory-image - initrd can have luci-mod-failsafe - flash final firmware via LuCI / sysupgrade on rebooted system via TFTP: - stop uboot into tftp-load into option "1" - upload factory.bin image Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ramips: let the "reserved" MTD partition be RO for R6220Enrico Mioso2017-05-311-0/+1
| | | | | | | | | | The "reserved" partition should probably be read-only, just in case. Even not knowing it's content, other devices have marked it as such, so it seems a good idea to do so also for this device. Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> CC: Mathias Kresin <dev@kresin.me> CC: Hanqing Wong <hquu@outlook.com>
* ramips: remove fictional LEDs from AsiaRF AWM00x device treeRussell Senior2017-05-271-14/+0
| | | | | | | | | Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module board. The ld1 and ld2 do not represent actual LEDs. These pins might connect to LEDS on an eval board or other carrier board, but that is outside the scope of this device tree file. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ramips: add support for GL-inet GL-MT300N-V2Kyson Lok2017-05-261-0/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-inet GL-MT300N-V2. Specification: - SoC: MediaTek MT7628AN - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR - Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps) - USB: 1 x USB 2.0 port - Button: 1 x switch button, 1 x reset button - LED: 3 x LEDS (system power led is not GPIO controller) - UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND) Installation through Luci: - The original firmware is LEDE, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Installation through bootloader webserver: - Plug power and hold reset button until red LED blink to bright. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Kyson Lok <kysonlok@gmail.com> [match maximum image size with firmware partition] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Asus RT-AC51UØrjan Malde2017-05-101-0/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A (580 MHz) - RAM: 64 MiB (Winbond W9751G6JB-25) - Flash: 16 MiB (Spansion S25FL128SAIF00) - LAN: x4 100M - WAN: x1 100M - Others: USB 2.0, reset button, wps button and 9 LEDs Issues: - 5 GHz band is not functional (missing driver support) Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75; Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the sysupgrade image, and press upload TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin tftp> quit Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
* ramips: add new device ZyXEL Keenetic as knAlexey Belyaev2017-05-101-0/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device exactly same as NBG-419N but with USB port and USB Led. Specification: - SoC: Ralink RT3052 (MIPS24Kc) @384MHz - RAM: 32 MiB - Flash: 8 MiB - WLAN: WiSoC 2T2R/300Mbps (2.4GHz) - LAN: 4x100M - WAN: 1x100M - USB: 1x2.0 Installation via serial console (57600 8N1) from TFTP server - rename the firmware to something shorter, for example "sysupgrade.bin" (max. 32 chars) - copy firmware TFTP server's directory - when you power on device, and see U-Boot log, immediatly push "2" once. - You will see this message: 2: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure? - Push "y", and enter: device IP, then TFTP server's IP, and then image firmware file name. The firmware will be downloaded within ~30 seconds and flashed to the device (It will take about 2 minutes). Signed-off-by: Alexey Belyaev <spider@spider.vc> [squash commits, compact commit message, fix compatible string, remove superfluous pinmuxes] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use GPIO_ACTIVE macros in UBNT-ERX.dtsSven Roederer2017-05-061-3/+4
| | | | | | | - reorder includes - use GPIO_ACTIVE_LOW macro instead of hardcoded "1" Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ramips: ZTE-Q7: fix switch driver initialization in DTS (FS#716)Jo-Philipp Wich2017-04-271-2/+4
| | | | | | | | | | Add the changes suggested by FS#716 to fix the switch driver initialization on the ZTE Q7. Also remove the `pinctrl-names` field obsoleted by the changes. Reported-by: Harry Lau <harrylwc@gmail.com> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: ZBT-WE826: include the correct dtsiMathias Kresin2017-04-273-6/+4
| | | | | | | | | Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the ZBT-WG3526 one. Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add ZBT-WE826 32MB variantMathias Kresin2017-04-253-5/+25
| | | | | | | | The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the device tree source file, rename the currently supported 16 MByte version and add the 32 MByte variant. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MBMathias Kresin2017-04-253-10/+3
| | | | | | | | The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and add the sdhci kernel module to use it for multiple clones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: prepare ZBT-WG3526 for hardware variantsMathias Kresin2017-04-251-1/+1
| | | | | | | | The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the current supported 16MByte version to indicate which flash size variant is supported. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for ZBT-WE1326Jiawei Wang2017-04-251-0/+107
| | | | | | | | | | | | | | | | | | | Specification: - SoC: MT7621AT, MT7603EN and MT7612EN - Flash: 16 MiB (W25Q128FVSG) - RAM: 512 MiB (EM6GE16EWXD-12H) - Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps) - Others: USB 2.0, micro SD slot, reset button and 8 x LEDs Issues: - Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs. - The pwr LED is not GPIO controllable How to install: - The original firmware is OpenWrt, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
* ramips: fix ZyXEL Keenetic Omni/Omni II GPIOsAlexey Belyaev2017-04-252-6/+22
| | | | | | | Each GPIO bank has only 24 gpios. Use and enable the correct banks for GPIOs > 24. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* ramips: fix ZyXEL Keenetic Omni switch configAlexey Belyaev2017-04-251-1/+1
| | | | | | | The wan port is connected to switch port 0. Fix the mediatek,portmap as well as the default switch config. Signed-off-by: Alexey Belyaev <spider@spider.vc>
* ramips: rename PSG1218 to match labelDaniel Golle2017-04-212-10/+10
| | | | | | | | Fix previous commit to be less ambigous: PSG1218 rev.A = 5 ports, external PA, heatsinks PSG1218 rev.B = 4 ports, internal PA, no heatsinks Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: split Phicomm PSG1218 and PSG1218K2CDaniel Golle2017-04-213-80/+124
| | | | | | | | | PSG1218 got only 4 Ethernet ports and WAN on port 3 while PSG1218K2C got 5 Ethernet ports and WAN on port 4 Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add RP-N53 pcie wireless eepromMathias Kresin2017-04-131-0/+9
| | | | | | | | | | Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata. Disable the 2.4GHz band as this band has no antennas attached but is enabled in the eeprom/caldata. Fixes: FS#691 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix WHR-600D eeprom dt propertyMathias Kresin2017-04-131-3/+3
| | | | | | | | | | | Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as this board have a RT5592 and uses the rt2x00 driver. The mediathek device tree bindings do not work here. Fixes: FS#691 Fixes: d8dd207ea6f2 ("ramips: use the ralink,mtd-eeprom device tree property") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Xiaomi MiWiFi Nano firmware partition sizeMathias Kresin2017-03-241-1/+1
| | | | | | | | | | Even the commit message of the patch adding support for the MiWiFi Nano says that a 16 MB flash chip is used. Extend the firmware partition to make use of all available flash space. Fixes: FS#622 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zbtlink ZBT-WE2026Vaclav Svoboda2017-03-171-0/+103
| | | | | | | | | | | | | | | | | | This patch adds support for the Zbtlink ZBT-WE2026. Specification: - SoC: MediaTek MT7620N (580MHz) - RAM: 64 MiB - Flash: 8 MiB SPI - LAN: 4x100M - WAN: 1x100M Installation through bootloader webserver: - With the power unplugged press and hold reset button. - Plug power and hold reset button until LED starts to blink. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ramips: add support for Netgear EX3700Joseph C. Lehner2017-03-121-0/+162
| | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. Co-authored-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: add support for Netgear R6220Hanqing Wong2017-03-121-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6220, aka Netgear AC1200 and R6220-100NAS. Specification: - SoC: MediaTek MT7621ST (880 MHz) - Falsh: 128 MiB (Macronix MX30LF1G08AA-TI) - RAM: 128 MiB (Nanya NT5CB64M16FP-DH) - Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 Installation through telnet: - Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port on the router. - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug (login if required, default: admin password) - You will see "Debug Enabled!" - Telnet 192.168.1.1 and login with "root" - ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for example. - cd /mnt/shares/myUdisk - mtd_write write rootfs.bin Rootfs - mtd_write write kernel.bin Kernel - reboot nmrpflash can be used to recover to the netgear firmware if a broken image was flashed. Signed-off-by: Hanqing Wong <hquu@outlook.com>
* ramips: Improve Sanlinking D240 configKristian Evensen2017-03-111-0/+11
| | | | | | | | | | | | | | | | | * The left most mini-PCIe slot (the one attached to SIM2) can be power-cycled by setting GPIO 0 to high/low. * The D240 only needs the MT76x2 module, so update makefile to reflect this. Note that until the default mt7620 target is updated, then kmod-mt76 (and thus kmod-mt7603) will be selected by default. v2->v3: * Indentation error. v1->v2: * Rename gpio and remove redundant comment (thanks Piotr Dymacz) Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for Afoundry EW-1200Francois Goudal2017-03-011-0/+127
| | | | | | | | | | | | | | | | | | | | | | This device features both a 2.4 and 5Ghz radio, and supports 802.11a/b/g/n/ac modes. It has 5 Gb-Ethernet ports and a USB 3.0 host port. It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi chipsets, together with 128MB of RAM and 16 MB of SPI Flash. The stock firmware is in fact based on some openwrt barrier breaker, with a mediatek SDK kernel, and an afoundry custom made web interface (not LuCI based). Firmware update page on the stock web interface can not accept sysupgrade images, it bricks the device. At this point, the only working solution I found was to connect to the serial console port (available on J4 header) and to use opkg to install dropbear. Then scp the sysupgrade file in the device's /tmp and run sysupgrade from console without preserving configuration files. Signed-off-by: Francois Goudal <francois@goudal.net>
* ramips: add support for HiWiFi HC5962ZengFei Zhang2017-02-281-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com Short specification: - MT7621AT + MT7612EN + 7603EN - 256MB DDR3 RAM - 128MB NAND flash - 1+3 x 1000M Ethernet - 1x USB 2.0 port. 1x USB 3.0 port. - reset button - UART pad on PCB (JP3: TX, RX, GND, 3.3V) Flash instruction: 1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin 2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/ 3, use the following commands: $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware $ mtd erase firmware_backup && reboot After reboot you should be able to login as root via SSH on 192.168.1.1 Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 03:24:54 +0000