aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-043-47/+127
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> (cherry picked from commit e38de40f8dd350344407fe5a91e81191f6960804)
* ramips: Cudy X6 fixes / improvementsFelix Baumann2023-04-301-14/+15
| | | | | | | | | | | | | | | | | | | | | | | - Correct WiFi MACs, they didn't match oem firmware - Move nvmem-cells to bdinfo partition and remove &bdinfo reference - Add OEM device model name R13 to SUPPORTED_DEVICES This allows sysupgrading from Cudy's OpenWrt fork without force - Label red_led and use it during failsafe mode and upgrades MAC addresses as verified by OEM firmware: use address source LAN b4:4b:d6:2d:c8:4a label WAN b4:4b:d6:2d:c8:4b label + 1 2g b4:4b:d6:2d:c8:4a label 5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [read wifi mac from flash offset] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 45cf200b2e22c34f2ae043b87e24230de526fefc)
* ramips: reduce Archer AX23 / MR70X SPI-frequencyDavid Bauer2023-04-272-2/+2
| | | | | | | | | | | | | | | It was brought to attention the Archer AX23 v1 fails to read jffs2 data from time to time. While this is not reproducible on my unit, it is on others. Reducing the SPI frequency does the trick. While it worked with at lest 40 MHz, opt for the cautious side and choose a save frequency of 25 MHz. Apply the same treatment to the Mercusys MR70X which uses a similar design just in case. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 2c530fcb972c112e7a2b10f9c21ac6d276624b5e)
* ramips: define remapping-range for DAP-X1860David Bauer2023-04-081-0/+7
| | | | | | | | | | Prevent the BBT translation layer from remapping the UBI used for storing rootfs. Explicitly define the number of blocks reserved for remapping. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 076da59f17803e9412ef5e50988aff6c7e536292)
* ramips: add support for D-Link DAP-X1860 A1Sebastian Schaper2023-04-081-0/+197
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The DAP-X1860 is a wall-plug AX1800 repeater. Specifications: - MT7621, 256 MiB RAM, 128 MiB SPI NAND - MT7915 + MT7975 2x2 802.11ax (DBDC) - Ethernet: 1 port 10/100/1000 - LED RSSI bargraph (2x green, 1x red/orange), status and RSSI LEDs are incorrectly populated red/orange (should be red/green according to documentation) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tar -xvf DAP-X1860_RevA_Firmware_101b94.bin - openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \ -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ== - tar -xvf FWImage.st1 - flash kernel_DAP-X1860.bin via Recovery Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> (cherry picked from commit 3c31f6b521bb5fc49e222a8f2bcd454b73452a0e)
* ramips: lower re305-v3 spi-max-frequencyJoe Mullally2023-04-081-1/+1
| | | | | | | | | | | | | | Fix flash I/O instability observed in newer devices with cFeon QH64A-104HIP (detected as en25qh64). Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91 Reported-by: Dimitri Souza <dimitri.souza@gmail.com> Tested-by: Dimitri Souza <dimitri.souza@gmail.com> Signed-off-by: Joe Mullally <jwmullally@gmail.com> [alter commit-message - target master] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 2122c80b321d439cf8b669ae26fcfeec605cf2cc)
* ramips: mt7621: mikrotik 760igs (hEX S) fix SFPJohn Thomson2023-04-021-0/+1
| | | | | | | | | | | | | | This device uses an AR8031/AR8033 chip to convert SoC gmac1 RGMII to 1000base-x or sgmii for the SFP fibre cage. The SFP cage requires phy-mode rgmii-rxid, and without it will not recieve any packets: ethtool -S sfp rx_fcs_errors will increase when packets should be being received, but no other _rx counters will change. Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> (cherry picked from commit 7ea965b57803ceec20222279377e611652ac217f)
* ramips: mt7621: ASUS RT-AX53U add NMBM, nest firmwareFelix Baumann2023-04-021-7/+26
| | | | | | | | | | | | | Nests kernel and ubi into firmware partition in-order to be compatible with OEM firmware. This allows restoring oem firmware from a backup of firmware2. Add jffs2 partition which is present in the oem firmware. Add support for mediatek NMBM (wear leveling on newer mediatek devices). Exclude UBI partition from NMBM management. Continues PR #10685. Tested-by: Felix Baumann <felix.bau@gmx.de> Signed-off-by: Felix Baumann <felix.bau@gmx.de> (cherry picked from commit 787ecdf66de6798540fb8b756404566341b4733c)
* ramips: add missing LEDs to Asus RT-AX53UMarian Sarcinschi2023-04-021-2/+12
| | | | | | | | | | | | | | | | | This patch adds the missing LEDs to Asus RT-AX53U. Based on PR #10400 and patch provided in #11068 - enable the two LEDs controlled by mt7915e for wireless; - add label to power LED so it works properly and fix formatting; - add the USB LED; - switch LEDs are best left to be controlled by hardware for now. Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com> Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Co-Authored-By: Hartmut Birr <e9hack@gmail.com> Tested-by: Felix Baumann <felix.bau@gmx.de> Tested-by: Marian Sarcinschi <znevna@gmail.com> Signed-off-by: Marian Sarcinschi <znevna@gmail.com> (cherry picked from commit c4b806d5c4ccc653968620e6e9aec93bc4e370e5)
* ramips: add support for read/write uboot env to Asus RX-AX53UFelix Baumann2023-04-021-2/+11
| | | | | | | | | | | | | | | | | | | Add support for read/writing uboot env by renaming the second partition to its stock label "nvram" and remove the deemed unnecessary "read-only". Split the first partition "u-boot" in two, in order to allow `fw_setenv` safe write-access to the uboot environment variables. This implements hauke's request from [1]. Based on the patch provided by Shiji Yang. [1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224 Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Signed-off-by: Felix Baumann <felix.bau@gmx.de> [ improve commit title and description, fix some whitespace problem ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 3f1e9f6f3b14385cab7ca6d1dcc2a4b658475bc3)
* ramips: add support for Mercusys MR70XDavid Bauer2023-03-241-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: Winbond W25Q128JV (SPI-NOR 16MB) - WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC) - UART: >TX RX GND 3v3 (115200 8N1, J1) Do not connect 3v3. TX is marked with an arrow. Installation ============ Flash factory image. This can be done using stock web ui. Revert to stock firmware ======================== Flash stock firmware via OEM Web UI Recovery mode. Web UI Recovery method ====================== 1. Unplug the router 2. Plug in and hold reset button 5~10 secs 3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0 4. Flash image with web browser to 192.168.1.1 Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 47de2c686291e69afc9f443e27e1dfd11ed5fbe7)
* ramips: add support for TP-Link Archer AX23 v1David Bauer2023-03-211-0/+203
| | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR () WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Upload the factory image using the Web-UI. Web-Recovery ------------ The router supports a HTTP recovery mode by holding the reset-button when powering on. The interface is reachable at 192.168.0.1 and supports installation using the factory image. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 7dceef5ee554ec4ab5d2dd2ff999f4a60bf2e0f4)
* ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2Arınç ÜNAL2023-02-031-1/+1
| | | | | | | | | The phy-mode property must be defined on the MAC instead of the PHY. Define phy-mode under gmac1 which the external phy is connected to. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 5155200f97adaeaaac7b752b5a6a5e41cba3db6a)
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-091-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit dce66899bf243d78689afcc693340b891bbf4c2d)
* ramips: improve compatibility for Youku YK-L2 and YK-L1 seriesShiji Yang2022-11-122-2/+4
| | | | | | | | | | | | | | | Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install initramfs-kernel.bin from the stock firmware Web UI. At the same time, this change makes it possible to boot OpenWrt with the official u-boot. Notice: Since the stock firmware is based on OpenWrt and the configuration will be retained by default during the upgrade process, so we must use initramfs-kernel.bin to do a initial installation. After the system restarts, install sysupgrade.bin and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit eba0a8deb65de70b0d913f9ec8910640a79d0191)
* ramips: gl-mt1300: downclock SPI to 50MHzMichael Lyle2022-11-121-2/+1
| | | | | | | | | | | | | | | | The SPI max frequency was set to 80MHz, considerably higher than the vendor clocks it in their firmware (10MHz). Multiple users reported jffs2 corruption/instability in GitHub issue #10461. My unit has a W25Q256; datasheet specifies maximum SPI frequency for read command of 50MHz. Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read; and @MPannen1979 for identifying the problem. Fixes: #10461 Signed-off-by: Michael Lyle <mlyle@lyle.org> (cherry picked from commit 961e01fc67e7d9e60557df3474fa326216aa4839)
* ramips: backport TP-Link RE200 v3/v4 LED fixSungbo Eo2022-11-085-11/+54
| | | | | | | | | | | | | | This backports a commit which fixes LEDs vor the RE200 like this: Set power LED to gpio 43 instead of 44 for v3 and v4. Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`). Tested by the author of the initial v3 and v4 commit. Tested-by: Richard Fröhning <misanthropos@gmx.de> Signed-off-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> (cherry picked from commit 02aa7a2bb9b6bdc8033d30c97f5b49534206a37c)
* ramips: Correct Unielec 01 and 06 dts wan macaddr byte locationDavid Bentham2022-10-303-6/+6
| | | | | | | | | | | Recent backport patch b5cb5f352d3133ac8384275be7d47264ad135e74 had missed changing the macaddr_factory address location. This patch corrects the address location. Fixes: b5cb5f352d31 ("ramips: fix WAN mac address allocation for Unielec 01 and 06 models") Signed-off-by: David Bentham <db260179@gmail.com> [Fix dts node name too] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix WAN mac address allocation for Unielec 01 and 06 modelsDavid Bentham2022-10-233-6/+15
| | | | | | | | | | | | | | | | | | | | | | | Manufacturer has predetermined mac address values for lan and wan ports. This change keeps inline with other mt7621 devices mac address allocation from factory mtd partition. Example from hexdump output: 0xe000 0x6 (lan) - 0xe006 0x6 (wan) 0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff Previous change had created an overlapping mac address situation as it would increment by one based on the lan mac address location found in the factory partition, which would sometimes increment to the same as the mt7603 wifi chip. Tested on Unielec u7621-01 model Signed-off-by: David Bentham <db260179@gmail.com> (cherry picked from commit 67660d36674c8c1504cbf3cd199409d0b209f802)
* ramips: fix ZyXEL NWA55AXE model nameDavid Bauer2022-10-141-1/+1
| | | | | | | The model name was missing a letter. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 9c8605dee238cdf52e88b6a1aa64d5b7bf5dd846)
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-10-143-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit a0b7fef0ffe4cd9cca39a652a37e4f3ce8f0a681)
* ramips: fix switch setup for ASUS RT-AX53UMatthias Schiffer2022-10-031-5/+0
| | | | | | | | The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface corresponding to the non-existing port. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 149fc3a269b435483b31df03d6fd9679286cf9e7)
* mac80211: rt2x00: experimental improvements for MT7620 wifiDaniel Golle2022-09-1916-15/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Serge Vasilugin reports: To improve mt7620 built-in wifi performance some changes: 1. Correct BW20/BW40 switching (see comments with mark (1)) 2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531 3. Set bbp66 for all chains. 4. US_CYC_CNT init based on Programming guide, default value was 33 (pci), set chipset bus clock with fallback to cpu clock/3. 5. Don't overwrite default values for mt7620. 6. Correct some typos. 7. Add support for external LNA: a) RF and BBP regs never be corrected for this mode b) eLNA is driven the same way as ePA with mt7620's pin PA but vendor driver explicitly pin PA to gpio mode (for forrect calibration?) so I'm not sure that request for pa_pin in dts-file will be enough First 5 changes (really 2) improve performance for boards w/o eLNA/ePA. Changes 7 add support for eLNA Configuration w/o eLAN/ePA and with eLNA show results tx/rx (from router point of view) for each stream: 35-40/30-35 Mbps for HT20 65-70/60-65 Mbps for HT40 Yes. Max results for 2T2R client is 140-145/135-140 with peaks 160/150, It correspond to mediatek driver results. Boards with ePA untested. Reported-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [directly include v3 of the patchset submitted upstream] (cherry picked from commit 31a6605de04218e1c04bd5c2436c24d7d1c07506) (cherry picked from commit e785ca05e9f0502894772f5df92192b816ba5d7c) (cherry picked from commit 412fcf3d4400f84551f3ead0514834c62d94a251)
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-181-0/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net> (cherry picked from commit 820f0c07c544652c1c53a45262a481ac5dbe139b)
* ramips: fix GB-PC1 and GB-PC2 LEDsArınç ÜNAL2022-09-182-14/+14
| | | | | | | | | | | | | | | | Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the device schematics. Tests on a GB-PC2 by me and Petr proved otherwise. Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired to GPIO 3 or 4 and the wiring is currently unknown. Set ethyellow-orange to display link state and activity of the ethyellow interface for GB-PC2. Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 2a6ef7f53d7b96e4ee0200196c28ed6b0a7c8465)
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-291-0/+16
| | | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: 158a5af80102d ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 7bee10a7d2d16251113147c28dd4548af5c14bab)
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-262-59/+59
| | | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 4807bd6a00bcf44dd821047db76a2a799f403cd4)
* ramips: create new dtsi for Arcadyan routersMikhail Zhilkin2022-08-162-186/+199
| | | | | | | | | | | | | | | | | | | | This commit moves common properties for the boards below to a new dtsi: Beeline Smartbox Flash (Arcadyan WG443223) MTS WG430223 (Arcadyan WG430223) The boards are almost the same. Here is the differences: +------+----------+----------+ | | WG430223 | WG443223 | +------+----------+----------+ | RAM | 128 | 256 | +------+----------+----------+ | USB | - | 1x3.0 | +------+----------+----------+ | LEDS | RG | RGB | +------+----------+----------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 5b59137a162c07738abbe9fd37125193b3107cb7)
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-08-161-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 498c15376bae109bfe130cc5581f83e4cc52c0f9)
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-08-161-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 8c00fd9b4519bf0ef8fb3470a6df421b9f38c03c)
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-08-091-0/+56
| | | | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com> (cherry picked from commit 1a8c74da709190e5157af9f5c2502b600f6273bb) Signed-off-by: Tom Herbers <freifunk@tomherbers.de>
* ramips: add support for Netgear WAX202Wenli Looi2022-07-211-0/+277
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0f068e7c4a83bcbf20c4e52a5f8a3f1fe2af2246)
* ramips: improve YunCore AX820 LEDsThibaut VARÈNE2022-07-011-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At least two AX820 hardware variants are known to exist, but they cannot be distinguished (same hardware revision, no specific markings). They appear to have the same LED hardware, but wired differently: - One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and a blue wlan5g LED at GPIO 16; - The other only offers a green system LED at GPIO 15, with GPIO 14 and 16 being apparently not connected Finally, a Yuncore datasheet says the canonical wiring should be: - Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16 All GPIOs are tied to a single RGB LED which is exposed via lightpipe on the device front casing. Considering the above, this patch exposes all three LEDs, preserves the common system LED (GPIO 15) as the openwrt status LED, and removes the color information from the LEDs names since it is not consistent across hardware. The LED naming is made consistent with other YunCore devices. A note is added in DTS to ensure this information is always available and prevent unwanted changes in the future. Fixes: #10131 "YunCore AX820: GPIO LED not correct" Reviewed-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: decrease SPI frequency for Phicomm K2PAviana Cruz2022-06-271-2/+1
| | | | | | | | | | | Some K2P comes with the worse boards with GD25Q128 (may be A2), which only works with 50MHz frequency and less. Reduce spi frequency so that these routers can boot. remove m25p,fast-read because it isn't needed for 50MHz SPI. Signed-off-by: Aviana Cruz <gwencroft@proton.me> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 857ea3f690aba8513b356926d9c430adafc7c50b)
* ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFPArınç ÜNAL2022-06-252-5/+7
| | | | | | | | | | | | | | | | | | | | For a TX->TX connected external phy to transmit/receive data, the rgmii2 pin group needs to be claimed with gpio function, at least for EdgeRouter X SFP. We already claim the pin group under the pinctrl node with gpio function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi. However, we should claim a pin group under its consumer node. It's the ethernet node in this case, which we already claim the rgmii2 pin group under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2 node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group under the pinctrl node. With this change, we also get to remove a definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to EdgeRouter X SFP. This change is tested on an EdgeRouter X SFP. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit a1ad8377355c41a7cc3012b707fcecab923cbc90)
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 535b0c70b1c466733b009144f81f5207f1ecd311)
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-061-2/+0
| | | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> (cherry picked from commit ce90ba1f3168e3f4581fd8581e2c0cd31efa14cf)
* ramips: add led_source for Asus RT-AC1200 devicesTamas Balogh2022-05-171-0/+1
| | | | | | | | | | | | | | | | this adds the mediatek,led_source dts binding for Asus RT-AC1200 devices' dtsi, for correct switch LED behavior. The dts-binding is introduced in commit: 65dc9e0980255b15402c45b840f239b85be59b3d Without this, we only have constantly very fast blinking LEDs, which don't react on any traffic or LAN events at all. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com> (cherry picked from commit 771ea6f2e3868b208b5261ae676160d5ef6544e8)
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-171-0/+178
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4a8eaa5c7c9235212c4af022c18b2dfbadfe557f)
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-171-0/+362
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 9ee6ac00c43cc253ac554495edb6214563ab1f31)
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-05-171-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit 32e6942d72b6426d65eaa4dc7f2ba949b3c32985)
* ramips: create shared DTSI for Wavlink WN53XAX devicesDavide Fioravanti2022-05-172-184/+207
| | | | | | | | Most of the definitions for WN531A6 will be shared with WN533A8 in a future commit, so put them in a shared DTSI. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit 57b6dcd826b13eab2101f9c8e96d43ab251e8dc1)
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-05-171-0/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com> (cherry picked from commit 39799974a372fb4333d21f077c670b8a56b9d696)
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-05-171-0/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> (cherry picked from commit 4891b865380e2b7f32acf0893df9c1ca9db8d4ea)
* ramips: zbt-wg2626: Add the reset gpio for PCIe port 1Alban Bedel2022-05-011-0/+3
| | | | | | | | | | | | | | The 2.4GHz interface doesn't come up properly with the log showing: mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) As seen on other MT7621 boards this is caused by a missing reset GPIO. The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO list to also reset the 2.4GHz interface on port 1. Signed-off-by: Alban Bedel <albeu@free.fr> (cherry picked from commit f953a1a4bfba2fa70c12bb80938aa66481a673b6)
* ramips: add support for OrayBox X3ARay Wang2022-04-191-0/+158
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com> (cherry picked from commit 9a750aae62de74b488d7df7bdbfa78cd606a8aaf)
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-193-130/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com> (cherry picked from commit a4bf562aa71ad1e3dcffa392b79110d803a93f11)
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-191-0/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com> (cherry picked from commit 78c3534645958c123aa82cec9926a34eed5dd5dd)
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-191-0/+148
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit bb505d82add5636da891bb97fdabc57947280e88)
* ramips: add support for D-Link DIR-878 R1Igor Nazarov2022-03-191-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) - Switch: 1 WAN, 4 LAN (Gigabit) - Buttons: Reset, WiFi Toggle, WPS - LEDs: Power, Internet, WiFi 2.4G WiFi 5G The R1 revision is identical to the A1 revision except - No Config2 Parition, therefore - factory partition resized to 64k from 128K - Firmware partition offset is 0x50000 not 0x60000 - Firmware partitions size increased by 64K - Firmware partition type is "denx,uimage", not "sge,uimage" - Padding of image creation "uimage-padhdr 96" removed Installation: Update to the last D-Link firmware through web-ui before OpenWRT installation then follow the instructions to patch your device using D-Link FailsafeUI. - D-Link FailsafeUI: Power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing, then jack into any lan port and manually assign a static IP address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2) and go to http://192.168.0.1 Flash with the factory image. Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-13 08:20:19 +0000