aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* Revert "ramips: add support for ipTIME AX2004M"Stijn Tintel2022-02-011-165/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit f4a79148f8cb ("ramips: add support for ipTIME AX2004M") seems to leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no longer boot. The leak is visible in u-boot: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0x840000e4 Data Size: 10750165 Bytes = 10.3 MiB Architecture: MIPS OS: Linux Load Address: 0x82000000 Entry Point: 0x82000000 Normally, it should look like this: Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.92 Type: Kernel Image Compression: lzma compressed Data Start: 0xbfca00e4 Data Size: 2652547 Bytes = 2.5 MiB Architecture: MIPS OS: Linux Load Address: 0x80001000 Entry Point: 0x80001000 Revert the commit to avoid more people soft-bricking their devices. This reverts commit f4a79148f8cbb7dfbcddfb0c1128caec45a01596. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for Wavlink WL-WN535K1Davide Fioravanti2022-01-301-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports and one fast ethernet port. Mine is branded as Talius TAL-WMESH1. It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3). The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could potentially work for WL-WN535G3R and WS-WN535G3R with little to none effort, but it's untested. Hardware -------- SoC: Mediatek MT7620A RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CS) ETH: - 2x 10/100/1000 Mbps Ethernet (RTL8211F) - 1x 10/100 Mbps Ethernet (integrated in SOC) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 internal antennas BTN: - 1x Reset button - 1x Touchlink button (set to WPS) - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 3x Green leds (ethernet port status/act) UART: - 57600-8-N-1 Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on WN535K1_V1510_200916 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: 16384+0 records in 16384+0 records out If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done 6) After few seconds, in the textarea should appear this output: 384+0 records in 384+0 records out 128+0 records in 128+0 records out 128+0 records in 128+0 records out 14720+0 records in 14720+0 records out 1024+0 records in 1024+0 records out If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro http://192.168.10.1/dev/mtd5ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update_mesh.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:E2 (factory @ 0x28) WAN XX:XX:XX:XX:XX:E3 (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:E4 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:E5 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:E5 2) The OEM firmware upgrade page accepts only files containing the string "WN535K1" in the filename. 3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid (https://github.com/openwrt/openwrt/commit/92780d80ab6f5f03fac2407c06eb267dd83914a1) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [remove trailing whitespace] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME AX2004MSungbo Eo2022-01-291-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specification: * SoC: MT7621A * RAM: 256 MiB * Flash: NAND 128 MiB * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 5x 1GbE * Switch: SoC built-in * USB: 1x 3.0 * UART: J4 (115200 baud) * Pinout: [3V3] (TXD) (RXD) (GND) MAC address: | interface | MAC | source | comment |-----------|-------------------|----------------|--------- | LAN | 58:XX:XX:00:XX:9B | | [1] | WAN | 58:XX:XX:00:XX:99 | | | WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4 | | WLAN 5G | 5A:XX:XX:40:XX:98 | | | | | | | | 58:XX:XX:00:XX:98 | config ethaddr | [1] Used in this patch as WLAN 5G MAC address with the local bit set Load address: * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation via **recovery** mode: 1. Press reset button, power up the device, wait >10s for CPU LED to stop blinking. 2. Upload recovery image through the recovery web page at 192.168.0.1. Revert to stock firmware: 1. Install stock image via recovery mode. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: correct vendor name for COMFAST/JoowinRodrigo Araujo2022-01-225-17/+17
| | | | | | | | | | | | | | | | When Joowin WR758AC V1 and V2 devices were added, they should have been added with the primary manufacturer name which is COMFAST, since Joowin is just an alternate vendor name on some coutries or stores. Fix this by changing the the vendor name on the respective files and set Joowin as ALT0 variants while ensuring compatibility for early users. Also adjust the model names to better follow the naming rules. As a side effect, fix mt76x8 network script which was left incorrectly unsorted on the case block conditions. Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2") Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: read Tenbay T-MB5EU address from single locationDavid Bauer2022-01-221-5/+2
| | | | | | | | | | | | | Currently the WAN MAC address is read from a different offset contrary to all other addresses. There's conflicting information whether offset 0x28 on the factory partition contains the valid WAN mac for all devices while 0x4 seems to be uniform. Read the WAN mac from this location and calculate it. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix reboot for remaining 32 MB boardsMichael Pratt2022-01-1522-7/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following devices have a Winbond W25Q256FV flash chip, which does not have the RESET pin enabled by default, and otherwise would require setting a bit in a status register. Before moving to Linux 5.4, we had the patch: 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch which kept specific flash chips with explicit 3-byte and 4-byte address modes to stay in 3-byte address mode while idle (after an erase or write) by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch. this was obsoleted by the patch: 481-mtd-spi-nor-rework-broken-flash-reset-support.patch which uses the newer upstream flag SNOR_F_BROKEN_RESET for devices with a flash chip that cannot be hardware reset with RESET pin and therefore must be left in 3-byte address mode when idle. The new patch requires that the DTS of affected devices have the property "broken-flash-reset", which was not yet added for most of them. This commit adds the property for remaining affected devices in ramips target, specifically because of the flash chip model. However, it is possible that there are other devices where the flash chip uses an explicit 4-byte address mode and the RESET pin is not connected to the SOC on the board, and those DTS would also need this property. Ref: 22d982ea0033 ("ramips: add support for switching between 3-byte and 4-byte addressing") Ref: dfa521f12953 ("generic: spi-nor: rework broken-flash-reset") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for ipTIME A6004NS-MSeongUk Moon2022-01-153-176/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MediaTek MT7621A (880MHz, Duel-Core) - RAM: DDR3 256MB - Flash: SPI NOR 16MB (Winbond W25Q128BV) - WiFi: MediaTek MT7615E (2.4GHz, 5GHz) - Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated) - USB: USB 3.0 x1 - UART: [3.3V, TX, RX, GND] (57600 8N1) Installation via web interface: 1. Flash initramfs image using OEM's Firmware Update page. 2. Connect to OpenWrt with an SSH connection to `192.168.1.1`. 3. Perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power on the device and connect the shell through UART. 2. Connect to the shell and press the `t` key on the keyboard. 3. Set fixed IP with `192.168.0.2` with subnet mask `255.255.255.0` 4. Flash image via TFTP to `192.168.0.1` Additional Notes: 1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz. 2. If the 5Ghz frequency is too high, 5Ghz may not work. 3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi). Signed-off-by: SeongUk Moon <antegral@antegral.net> [convert CRLF to LF] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for HUMAX E2Kyoungkyu Park2022-01-151-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB (MXIC MX25L6405D) - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610E - Ethernet: 1x 10/100Mbps - Switch: SoC internal - UART: J2 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation and Recovery via TFTP: 1. Connect ethernet cable between Router port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) 5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!** The device will be automatically rebooted. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
* ramips: enable badblock table support on linksys ea7xxx devicesFelix Fietkau2022-01-131-0/+5
| | | | | | Use remapping only on the kernel partitions. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mikrotik: make soft_config writableOskari Lemmela2022-01-131-1/+0
| | | | | | Parent mtd partition needs to be writable Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* ramips: add support for Linksys EA6350 v4Nick McKinney2022-01-081-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net>
* ramips: add support for RAISECOM MSG1500 X.00Liangkuan Yang2022-01-081-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router. Apart from the general model, there are two ISP customized models: China Mobile and China Telecom. Specifications: - SoC: Mediatek MT7621AT - RAM: 256MiB DDR3 - Flash: 128MiB NAND - Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN - Switch: MediaTek MT7530 (SoC) - WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps) - USB: 1 * USB 2.0 port - Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button - LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB - UART: 1 * serial port header (4-pin) - Power: DC 12V, 1A - Switch: 1 * POWER switch MAC addresses as verified by vendor firmware: use address source LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label) WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii 5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex 2.4G CA:XX:XX:4A:XX:E8 [not on flash] The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30 C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10 C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Notes: 1. The vendor firmware allows you to connect to the router by telnet. (known version 1.0.0 can open telnet.) There is no official binary firmware available. Backup the important partitions data: "Bootloader", "Config", "Factory", and "firmware". Note that with the vendor firmware the memory is detected only 128MiB and the last 512KiB in NAND flash is not used. 2. The POWER LED is default on after press POWER switch. The WAN and LAN1 - 4 LEDs are wired to ethernet switch. The WPS LED is controlled by MT7615DN's GPIO. Currently there is no proper way to configure it. 3. At the time of adding support the wireless config needs to be set up by editing the wireless config file: * Setting the country code is mandatory, otherwise the router loses connectivity at the next reboot. This is mandatory and can be done from luci. After setting the country code the router boots correctly. A reset with the reset button will fix the issue and the user has to reconfigure. * This is minor since the 5g interface does not come up online although it is not set as disabled. 2 options here: 1- Either run the "wifi" command. Can be added from LuCI in system - startup - local startup and just add wifi above "exit 0". 2- Or add the serialize option in the wireless config file as shown below. This one would work and bring both interfaces automatically at every boot: config wifi-device 'radio0' option serialize '1' config wifi-device 'radio1' option serialize '1' Flash instructions using initramfs image: 1. Press POWER switch to power down if the router is running. 2. Connect PC to one of LAN ports, and set static IP address to "10.10.10.2", netmask to "255.255.255.0", and gateway to "10.10.10.1" manually on the PC. 3. Push and hold the WIFI button, and then power up the router. After about 10s (or you can call the recovery page, see "4" below) you can release the WIFI button. There is no clear indication when the router is entering or has entered into "RAISECOM Router Recovery Mode". 4. Call the recovery page for the router at "http://10.10.10.1". Keep an eye on the "WARNING!! tip" of the recovery page. Click "Choose File" to select initramfs image, then click "Upload". 5. If image is uploaded successfully, you will see the page display "Device is upgrading the firmware... %". Keep an eye on the "WARNING!! tip" of the recovery page. When the page display "Upgrade Successfully", you can set IP address as "automatically obtain". 6. After the rebooting (PC should automatically obtain an IP address), open the SSH connection, then download the sysupgrade image to the router and perform sysupgrade with it. Flash back to vendor firmware: See "Flash instructions 1 - 5" above. The only difference is that in step 4 you should select the vendor firmware which you backup. Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
* ramips: add support for Joowin WR758AC V1 and V2Rodrigo Araujo2022-01-083-0/+140
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2 devices. Both have the same wall AP/repeater form factor and differ only in the 5Ghz chipset (V1 has MT7662, V2 has MT7663). OpenWrt developers forum page: https://forum.openwrt.org/t/87355 Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB DDR2 - 2.4 GHz: 802.11b/g/n (MT7603) - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663) - Antennas: 4x external single band antennas - LAN: 1x 10/100M - LED: Wifi 3x blue. Programmable - Button: WPS MAC addresses as verified by OEM firmware: use address source LAN *:83 factory 0xe000 2g *:85 factory 0x4 5g *:86 factory 0x8004 How to install: 1- Setup a TFTP server on a machine with IP address 192.168.1.10/24 2- Name the image as `firmware_auto.bin` and place it on the root of the TFTP server 3- Connect the device via Ethernet, it should pick and flash the image Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: add support for ipTIME T5004Sungbo Eo2022-01-021-0/+121
| | | | | | | | | | | | | | | | | | | | | | | | ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A. Specifications: * SoC: MT7621AT * RAM: 128 MiB * Flash: NAND 128 MiB * Ethernet: 5x 1GbE * Switch: SoC built-in * UART: J4 (57600 baud) * Pinout: [3V3] (TXD) (RXD) (GND) Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware via recovery mode: 1. Press reset button, power up the device, wait >15s for CPU LED to stop blinking. 2. Upload stock image to TFTP server at 192.168.0.1. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME A3004TWonJung Kim2021-12-291-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim <git@won-jung.kim> (added led dt-bindings) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for WeVO AIR DUOSungbo Eo2021-12-291-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on MediaTek MT7620A. Specifications: * SoC: MT7620A * RAM: 64 MiB * Flash: SPI NOR 16 MiB * USB & SATA bridge controller: JMicron JMS567 * SATA 6Gb/s: 2.5" drive slot * USB 3.0: Micro-B * USB 2.0: connected to SoC * Wi-Fi: * 2.4 GHz: SoC built-in * 5 GHz: MT7612EN * Ethernet: 5x 1GbE * Switch: MT7530WU * UART: 4-pin 1.27 mm pitch through-hole (57600 baud) * Pinout: (3V3)|(RXD) (TXD) (GND) Notes: * The drive is accessible through the external USB port only when the router is turned off. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. The image filename should have ".upload" extension. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: work around duplicate MAC address on U6 LiteDavid Bauer2021-12-201-0/+15
| | | | | | | | | | | | | | | | | | | | | | The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in it's EEPROM partition. On my unit these are F4 92 BF A0 BB 6F F6 92 BF A0 BB 6F The problem with these is that mac80211 increases the first octet by 2, which leads to conflicting MAC addresses between radios. Work around this problem for now by increasing the last octet by 1 on the 5 GHz radio. Ubiquiti increases the last octet by 2 for each subsequent VAP created per radio. Ideally we should do the same, however this functionality is currently lacking from mac80211. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7620: use OKLI loader with Jboot devicesPawel Dembicki2021-12-138-8/+32
| | | | | | | | | | | Jboot devices have problem with >2MB kernelsize. The only way to avoid this problem is use small loader. This patch switch all mt7620 Jboot devices to lzma OKLI loader. Suggested-by: Szabolcs Hubai <szab.hu@gmail.com> Co-authored-by: Michael Pratt <mcpratt@pm.me> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for HUMAX E10Kyoungkyu Park2021-12-121-0/+170
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router, based on MediaTek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 128MB - Flash: SPI NOR 16MB (MXIC MX25L12805D) - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 2x 10/100/1000Mbps - Switch: SoC internal - USB: 1x USB 2.0 Type-A - UART: J1 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation via web interface: - Flash **factory** image through the stock web interface. Recovery procedure: 1. Connect ethernet cable between Router **LAN** port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) - It can accept both images which is HUMAX stock firmware dump (0x70000-0x1000000) image and OpenWRT **sysupgrade** image. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space> [remove trailing whitespace] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for Zbtlink ZBT-WG1602Sergey Ryazanov2021-12-052-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN (UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe slots with USB and SIM only and another one pure miniPCIe slot as well as five Gigabit Ethernet ports (4xLAN + WAN). Specification: * SoC: MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * external watchdog (looks like Torexsemi XC6131B) * Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * WLAN 2GHz: MT7603EN (.11n, MIMO 2x2) * WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2) * WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios * miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus * WWAN Ants: detachable x4 * External storage: microSD (SDXC) slot * USB: 2.0 Type-A port * LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1 power indicator) * Button: 1 (reset) * UART: console (115200 baud) * Power: DC jack (12 V / 2.5 A) Additional HW information: * SoC USB port #1 is shared by internal miniPCIe slot and external Type-A USB port, USB D+/D- lines are toggled between ports using a GPIO controlled DPDT switch. * Power of the USB enabled miniPCIe slots can be individually controlled using dedicated GPIO lines. * Vendor firmware feeds the external watchdog with 1s pulses. GPIO watchdog driver is able to either generate a 1us pulses or toggle the output line. 1us is not enough for the external watchod timer, so the line toggling driver mode is utilized. Installation: Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ramips: add support for ipTIME A3004NS-dualYuchan Seo2021-12-041-0/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7602E - 5GHz : MT7612E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: - 1. Flash Initramfs image using OEM Firmware's web GUI - 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image. Revert to stock firmware: - 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image. Signed-off-by: Yuchan Seo <hexagonwin@disroot.org> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: Enable PHY aneg of Lava LR-25G001Pawel Dembicki2021-12-041-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | In 20b09a2125f5 Lava LR-25G001 router have problem with two inactive ethernet ports. JBOOT bootloader didn't configure ethernet devices by default. The same situation was there. It is required to enable all phy ports. This is fragment of stock bootlog: switch reg write_athr offset=90, value=2b0 switch reg write_athr offset=8c, value=2b0 switch reg write_athr offset=88, value=2b0 switch reg write_athr offset=84, value=2b0 switch reg write_athr offset=80, value=2b0 This patch adds proper registers configuration ar8337 initvals. 0x2b0 value causes force flow control configuration, 0x1200 was used instead (flow control config auto-neg with phy). [1] When switch is now ok, let's fix port numeration too. Fixes: 20b09a2125f5 ("ramips: add support for Lava LR-25G001") [1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for Wavlink WL-WN576A2Thomas Aldrian2021-11-201-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles repeater / router. It is also sold under the name SilverCrest SWV 733 B1. Device specs: - CPU: MediaTek MT7628AN - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - 5 GHz: a/n/ac MT7610EN - Buttons: WPS, reset, sliding switch (ap/repeater) - LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS Flashing: U-Boot launches a TFTP client if WPS button is held during boot. - Server IP: 192.168.10.100 - Firmware file name: firmware.bin Device will reboot automatically. First boot takes about 90s. Coelner (waenger@gmail.com) is the original author, but I have made some fixes. He does not wish to sign off using his real name. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* ramips: add broken-flash-reset for HLK-7621A EvBWout Bertrums2021-11-061-0/+1
| | | | | | | | | | This is needed because the HLK-7621 EvB has 32MB of flash, so it will have to use 4B addressing and the broken-flash-reset hack has to be used to be able to reboot. Signed-off-by: Wout Bertrums <wout@wbnet.eu> [copied github message into commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: mt7621-dts: properly organize pcie nodeSergio Paracuellos2021-11-061-10/+8
| | | | | | | | | | | Device tree pcie node for this SoC is using different styles in its different properties. Hence properly unify them to be able to write a a proper yaml schema documentation. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: add missing device_type in pcie root portsSergio Paracuellos2021-11-061-0/+3
| | | | | | | | | According to the YAML schema 'pci-bus.yaml' the 'device_type' property is mandatory for all pcie root ports. Hence add it. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: remove 'bug-range' propertySergio Paracuellos2021-11-061-4/+0
| | | | | | | | | Property 'bus-range' when values are the default are not necessary to be defined. Hence, remove all of them. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: use standard 'syscon' stringSergio Paracuellos2021-11-061-4/+4
| | | | | | | | | | Both 'memc' and 'sysc' nodes are not using 'syscon' as a node string which is the standard one to be used. Update both of them. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: remove ethsys nodeSergio Paracuellos2021-11-061-8/+1
| | | | | | | | | | | | | | | | DT 'ethsys' node is being configured as a syscon to get access to reset and other registers in the 'mediateķ,mt7621-eth' driver. Since the 'sysc' is also a syscon, provides the clock and also is virtually mapped from the same physical address 0x1e000000 we can just use 'sysc' as the phandle for the syscon in the ethernet node. Compatible string 'mediatek,mt7621-ethsys' of the node is not being used anywhere inside the kernel so, this node can be safely removed. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20210505132154.8263-2-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: remove obsolete switch nodeDENG Qingfang2021-11-061-7/+0
| | | | | | | | | | This was for OpenWrt's swconfig driver, which never made it upstream, and was also superseded by MT7530 DSA driver. Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> Link: https://lore.kernel.org/r/20210108025155.31556-1-dqfext@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: properly define 'cpc' and 'mc' nodesSergio Paracuellos2021-11-061-10/+10
| | | | | | | | | | | | | | | | 'cpc' and 'mc' nodes correspond with the MIPS 'Cluster Power Controller' and 'MIPS Common Device Memory Map' which are present in some MIPS related boards. There is already bindings documentation for these two located in: - Documentation/devicetree/bindings/power/mti,mips-cpc.yaml - Documentation/devicetree/bindings/bus/mti,mips-cdmm.yaml Hence, properly update compatible strings and align nodes with already mainlined bindings documentation. Also, move their definition to a proper place since both of them are not related with the palmbus at all. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20211002060706.30511-1-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: change some node hex addresses to lower caseSergio Paracuellos2021-11-061-6/+6
| | | | | | | | | Hexadecimal addresses in device tree must be defined using lower case. There are some of them that are still in upper case. Change them all. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20211017070656.12654-2-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: mt7621-dts: make use of 'IRQ_TYPE_LEVEL_HIGH' instead of magic numbersSergio Paracuellos2021-11-061-2/+2
| | | | | | | | | | Nodes 'gdma' and 'hsdma' are using magic number '4' in interrupts property. Use 'IRQ_TYPE_LEVEL_HIGH' instead to align with the rest of the nodes in the file. Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20211019102915.15409-2-sergio.paracuellos@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: add support for HiLink HLK-7621A evaluation boardSergio Paracuellos2021-10-311-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB (DDR3) - Flash: 32 MB SPI NOR 44MHz - Switch: 1 WAN, 4 LAN (Gigabit) - LEDs: 1 WAN, 4 LAN (controlled by PHY) - USB Ports: 1 x USB2, 1 x USB3 - WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E) - Button: 1 button (reset) - UART Serial: UART1 as console : 57600 baud - Power: 12VDC, 1A Installation: Update openWRT firmware using internal GNUBEE uboot: https://github.com/gnubee-git/GnuBee-MT7621-uboot By HTTP: Initial uboot address is http://10.10.10.123, your address needs to be 10.10.10.x, and mask 255.255.255.0. By TFTP: Uboot is in client mode, the address of the firmware must be tftp://10.10.10.3/uboot.bin Recovery: Manufacturer provides MTK OpenWrt 14.07 source code, compile then flash it by uboot. HLK-7621A is a stamp hole package module for embedded development, users have to design IO boards to use it. MAC addresses: - u-boot-env contains a placeholder address: > mtd_get_mac_ascii u-boot-env ethaddr 03:17:73:ab:cd:ef - phy0 gets a valid-looking address: > cat /sys/class/ieee80211/phy0/macaddress f8:62:aa:**:**:a8 - Calibration data for &pcie2 contains a valid address, however the zeros in the right half look like it's not real: 8c:88:2b:00:00:1b - Since it's an evaluation board and there is no solid information about the MAC address assignment, the ethernet MAC address is left random. Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn> [add keys and pcie nodes to properly support evaluation board] Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> [remove ethernet address, wrap lines properly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi MiWifi 3CEduardo Santos2021-10-311-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix LAVA LR-25G001 broken wifi led triggersJani Partanen2021-10-301-0/+2
| | | | | | | | | | | | | | | LED labels for this device are different in 01_leds file and in device DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone device. This has not been tested on the LR-25G001 itself, just on the clone mentioned above. Fixes: 20b09a2125f5 ("ramips: add support for Lava LR-25G001") Signed-off-by: Jani Partanen <rtfm@iki.fi> [rephrase commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE305 v3Michal Kozuch2021-10-303-81/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specs (same as in v1): - MT7628AN (575 MHz) - 64MB RAM - 8MB of flash (SPI NOR) - 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan) - 1x 2.4GHz wifi (MT7628AN) - 1x 5Ghz wifi (MT7612E) - 4x LEDs (5 GPIO-controlled) - 1x reset button - 1x WPS button The only and important difference between v1 & v3 is in flash memory layout, so pls don't interchange these 2 builds! Installation through web-ui (on OEM factory firmware): 1. Visit http://tplinkrepeater.net or the configured IP address of your RE305 v3 (default 192.168.0.254). 2. Log in with the password you've set during initial setup of the RE305 (there is no default password). 3. Go to Settings -> System Tools -> Firmware upgrade 4. Click Browse and select the OpenWRT image with factory.bin suffix (not sysupgrade.bin) 5. A window with a progress bar will appear. Wait until it completes. 6. The RE305 will reboot into OpenWRT and serve DHCP requests on the ethernet port. 7. Connect an RJ45 cable from the RE305 to your computer and access LuCI at http://192.168.1.1/ to configure (or use ssh). Disassembly: Just unscrew 4 screws in the corners & take off the back cover. Serial is exposed to the right side of the main board (in the middle) and marked with TX/RX/3V3/GND, but the holes are filled with solder. Installation through serial: 1. connect trough serial (1n8, baudrate=57600) 2. setup the TFTP server and connect it via ethernet (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc) 3. boot from a initramfs image first (choose 1 in the bootloader options) 4. test it a bit with that, then proceed to run sysupgrade build MAC addresses as verified by OEM firmware: use OpenWrt address reference LAN eth0 *:d2 label 2g wlan0 *:d1 label - 1 5g wlan1 *:d0 label - 2 The label MAC address can be found in config 0x2008. Signed-off-by: Michal Kozuch <servitkar@gmail.com> [redistribute WLAN node properties between DTS/DTSI, remove compatible on DTSI, fix indent/wrapping, split out firmware-utils change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: minew g1-c: Allow dynamic RAM sizesBruno Randolf2021-10-261-5/+0
| | | | | | | | Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB versions of Minew G1-C. This is also in line with the behaviour of most other RAMIPS boards. Signed-off-by: Bruno Randolf <br1@einfach.org>
* ramips: fix dtc warnings for telco-electronics_x1Rosen Penev2021-10-171-16/+17
| | | | | | | In all other dts files, the entire block is not edited like this. They're edited separately. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix USW-Flex reversed switch-port orderDavid Bauer2021-10-041-4/+4
| | | | | | | Switch port order was reversed due to reading the internal labling (which mismatches the one on the case). Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear R7450Dale Hui2021-09-261-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | Netgear R7450 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [fix model/compatible in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear R6900v2Dale Hui2021-09-261-0/+15
| | | | | | | | | | | | | | | | | | | | | | | Netgear R6900v2 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
* ramips: make Netgear R7200 a separate device from R6700v2Dale Hui2021-09-261-0/+15
| | | | | | | | | With the various variants of Netgear R**** devices, make it more obvious which image should be used for the R7200. Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [provide proper commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Ubiquiti USW-FlexDavid Bauer2021-09-251-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7621AT 16M SPI-NOR Macronix MX25L12835FMI Microchip PD69104B1 4-Channel PoE-PSE controller TI TPS2373 PoE-PD controller PoE-Controller -------------- By default, the PoE outputs do not work with OpenWrt. To make them output power, install the "poemgr" package from the packages feed. This package can control the PD69104B1 PSE controller. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt" via SSH. 2. Add the uboot-envtools configuration file /etc/fw_env.config with the following content $ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config 3. Update the bootloader environment. $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 4. Transfer the OpenWrt sysupgrade image to the device using SCP. 5. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 6. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 8. Reboot the device. It should boot into OpenWrt. Restore to UniFi ---------------- To restore the vendor firmware, follow the Ubiquiti UniFi TFTP recovery guide for access points. The process is the same for the Flex switch. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-DX2033GRINAGAKI Hiroshi2021-09-251-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI) - WLAN : 2.4/5 GHz - 2.4 GHz : 2T2R, MediaTek MT7603E - 5 GHz : 4T4R, MediaTek MT7615 - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: 3.3V, TX, RX, NC, GND from triangle mark - 57600n8 - Power : 12 VDC, 1 A Flash instruction using initramfs image: 1. Boot WN-DX2033GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, download the sysupgrade.bin image to the device and perform sysupgrade with it 5. Wait ~120 seconds to complete flashing Notes: - The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and it is certified under the same radio-wave related regulations in Japan - The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" (called as "combo image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB") - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32" - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b) : kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs - There are 2x important flags in the flash: - bootnum : select os partition for booting (persist, 0x4) - 0x01: firmware - 0x02: firmware_2 - debugflag : allow interrupt kernel loader, it's named as "Z-LOADER" (Factory, 0xFE75) - 0x00: disable debug - 0x01: enable debug MAC addresses: LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text)) WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex)) 2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex)) 5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add missing information to dlink headersAlan Luck2021-09-241-2/+0
| | | | | | | | | | | | Add additional header information required for newer bootloaders found on DIR-2660-A1 & A2. Also remove the MTD splitter compatible from the second firmware partition, as OpenWrt only supports handling of the first one. Signed-off-by: Alan Luck <luckyhome2008@gmail.com> [rephrase commit message, remove removal of read-only flags] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Sitecom WLR-4100 v1 002Andrea Poletti2021-09-051-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router Specification: SoC: MT7620A RAM: 64 MB DDR2 Flash: MX25L6405D SPI NOR 8 MB WIFI: 2.4 GHz integrated Ethernet: 5x 10/100/1000 Mbps QCA8337 USB: 1x 2.0 LEDS: 2x GPIO controlled, 5x switch Buttons: 1x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB: VCC 3.3V GND TX RX baud: 115200, parity: none, flow control: none Installation Connect to one of LAN (yellow) ethernet ports, Open router configuration interface, Go to Toolbox > Firmware, Browse for OpenWrt factory image with dlf extension and hit Apply, Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues Some USB 2.0 devices work at full speed mode 1.1 only MAC addresses factory partition only contains one (binary) MAC address in 0x4. u-boot-env contains four (ascii) MAC addresses, of which two appear to be valid. factory 0x4 **:**:**:**:b9:84 binary u-boot-env ethaddr **:**:**:**:b9:84 ascii u-boot-env wanaddr **:**:**:**:b9:85 ascii u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii The factory firmware only assigns ethaddr. Thus, we take the binary value which we can use directly in DTS. Additional information OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), based on RT3352 SoC Signed-off-by: Andrea Poletti <polex73@yahoo.it> [remove config DT label, convert to nvmem, remove MAC address setup from u-boot-env, add MAC address info to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: w2914ns-v2: consolidate leds nodes into dtsiSungbo Eo2021-08-304-33/+11
| | | | | | | | | | | | w2914ns-v2, 11acnas, and freezio use almost same board and thus share a common dtsi file. Now that LED labels do not contain "devicename" since commit c846dd91f0a6 ("ramips: remove model name from LED labels"), let's move the leds nodes to dtsi and remove them from dts. Note that freezio has only one USB 3.0 port and adding &ehci_port2 trigger does not incur any visible changes. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add label-mac for TL-MR3020 v3David Bauer2021-08-281-0/+1
| | | | | | | | The TP-Link TL-MR3020 v3 only has a single MAC address assigned for ethernet LAN as well as WiFi. This MAC address is also printed on the casing. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: enable fast-read for TL-MR3020 v3David Bauer2021-08-281-0/+1
| | | | | | | | The GigaDevices GD25Q64B found on the TL-MR3020 v3 supports the fast read instruction. Add the required DT property in order to enable usage of this property. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-29 09:11:08 +0000