aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: convert TP-Link MT7620 boards to tpt triggerDavid Bauer2020-01-026-1/+8
| | | | | | | | | | | | This converts all MediaTek MT7620 boards from TP-Link to use the now supported WiFi throughput LED trigger. This way, the LED state now covers all VAPs regardless of their name. Also align all single-WiFi LEDs to represent the state of the 2.4GHz radio. This was not always the case previously, as later-added support for the MT7610 altered the phy probing order. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7620: use throughput trigger on HiWiFi HC5x61DENG Qingfang2019-12-313-0/+5
| | | | | | Throughput trigger support for MT7620 has been added, so switch to it Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: remove HiWiFi HC5661 non-existent 5GHz LEDDENG Qingfang2019-12-311-5/+0
| | | | | | | | HC5661 does not have 5GHz WiFi or LED. Fixes: e6e373d3480e ("ramips: Add DTS files for HiWiFi HC5x61 models") Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for TP-Link RE200 v1Andreas Böhler2019-12-311-0/+158
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN. Specifications -------------- - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled; only 6 supported), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. The 5G LED is currently not supported, since the GPIOs couldn't be determined. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. Additional notes ---------------- MAC address assignment is based on stock-firmware. For me, the device assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G WiFi has a separate MAC with +2. *:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158 *:89 unused userconfig 0x0160 *:8A 5G not present in flash This seems to be the first ramips device with a TP-Link v1 header. The original firmware has the string "EU" embedded, there might be some region- checking going on during the firmware upgrade process. The original firmware also contains U-Boot and thus overwrites the boot loader during upgrade. In order to flash back to stock, the first header and U-Boot need to be stripped from the original firmware. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: fix switch setup for Xiaomi MiWiFi NanoSungbo Eo2019-12-311-0/+5
| | | | | | | MiWiFi Nano has two LAN ports, which are in reverse order. Add port numbers to them, and disable unused ports. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: remove bogus ralink,mtd-eeprom with offset 0x4Adrian Schmutzler2019-12-276-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several devices in mt76x8 subtarget use the following line to set up wmac in their DTS(I) files: ralink,mtd-eeprom = <&factory 0x4> This is strange for several reasons: - They should use mediatek,mtd-eeprom on this SOC - The caldata is supposed to start at 0x0 - The parent DTSI mt7628an.dtsi specifies mediatek,mtd-eeprom anyway, starting from 0x0 - The offset coincides with the default location of the MAC address in caldata Based on the comment in b28e94d4bfa1 ("ramips: MiWiFi Nano fixes"), it looks like the author for this device wanted to actually use mtd-mac-address instead of ralink,mtd-eeprom. A check on the same device revealed that actually the MAC address start at offset 4 there, so the correct caldata offset is 0x0. Based on these findings, and the fact that the expected location on this SOC is 0x0, we remove the "ralink,mtd-eeprom = <&factory 0x4>" statement from all devices in ramips (being only mt7628an anyway). Thanks to Sungbo Eo for finding and researching this. Reported-by: Sungbo Eo <mans0n@gorani.run> Fixes: b28e94d4bfa1 ("ramips: MiWiFi Nano fixes") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: simplify state_default/pinctrl0 in device DTS filesAdrian Schmutzler2019-12-23295-1941/+1355
| | | | | | | | | The node pinctrl0 is already set up in the SOC DTSI files, but defined again as member of pinctrl in most of the device DTS(I) files. This patch removes this redundancy for the entire ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix MAC address setup for Xiaomi MiWiFi NanoSungbo Eo2019-12-221-0/+1
| | | | | | | | MAC addresses are stored in factory partition at: 0x0004: WiFi 2.4GHz (label_mac +1) 0x0028: LAN, WAN (label_mac) Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: further improve support for Xiaomi MiWiFi NanoSungbo Eo2019-12-221-15/+13
| | | | | | | | | | | | | | | | | This patch does the following: - prepend vendor name to model - set status LEDs to follow the behavior in stock FW - simplify state_default node definition - use generic name for flash node Stock FW status indicators: https://files.xiaomi-mi.com/files/Mi_Router_Wi-Fi_Nano/Mi_router-NANO_EN.pdf > Yellow: power on / off > Blue: during normal operation > Red: in case of problems with the operation of the device Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: further DTS improvements for Edimax RG21SAdrian Schmutzler2019-12-221-8/+6
| | | | | | | | | | This fixes the state_default node by setting the correct groups and inheriting &state_default from parent DTSI directly. The compatible for the wifi nodes is changed to the more generic mediatek,mt76. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add eth0 MAC address for Edimax RG21SAdrian Schmutzler2019-12-221-0/+3
| | | | | | | | | | | | | | | So far, lan/wan MAC address for Edimax RG21S are only read using mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but eth0 address is random. Since the device's LAN address is the same as for 2.4 GHz, though, this patch set's the eth0 address based on the 2.4 GHz one, which can be extracted by mtd-mac-address. This will also allow to move the label MAC address setup to DT. The setup of lan_mac and wan_mac are kept in 02_network, so those locations are still in use, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix portmap for TP-Link Archer C50 v4Maxim Anisimov2019-12-191-1/+1
| | | | | | According to 02_network portmap is wan=0 lan1=1 lan2=2 lan3=3 lan4=4 Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for ipTIME A104nsSungbo Eo2019-12-172-0/+145
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A. Specifications: - SoC: MT7620A - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7610EN - Ethernet: 5x 10/100Mbps - Switch: SoC internal - USB: 1x 2.0 - UART: - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. In contrast to to-be-supported A1004ns, the A104ns has no usable value in 0x1fc40 (uboot), so wan_mac needs to be calculated. Also note that GPIOs for the LEDs really are inverted compared to the A1004ns. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [moved state_default to device DTS, reordered properties in wmac, added comment about wan_mac and LED GPIOs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: increase SPI frequency for Edimax RG21SBirger Koblitz2019-12-171-1/+1
| | | | | | | | This increases SPI frequency from the relatively low 10 MHz to 40 MHz. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [added commit title/message, split patch] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove unnecessary nodes in DTS for Edimax RG21SBirger Koblitz2019-12-171-10/+0
| | | | | | | | | This sdhci and i2c nodes were copy-pasted, but are not needed as the device does not provide that functionality. Remove them. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [added commit title/message, split patch] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG JHR-AC876MDENG Qingfang2019-12-131-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JCG JHR-AC876M is an AC2600M router Hardware specs: SoC: MT7621AT 2.4GHz: MT7615N 4x4 @ PCIe0 5GHz: MT7615N 4x4 @ PCIe1 Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB USB 2.0 and 3.0 ports 6 LEDs, 3 of which are connected to SoC GPIO Reset and WPS buttons Flash instructions: Stock to OpenWrt: Upload factory.bin in stock firmware's upgrade page, do not preserve settings OpenWrt to stock: Push and hold the reset button for 5s while power cycling to enter recovery mode; Visit 192.168.1.1 and upload stock firmware MAC addresses map: 0x0004 *:1c wlan2g/wan/label 0x8004 *:20 wlan5g 0xe000 *:1b lan 0xe006 *:1a not used in stock fw Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for ipTIME A6ns-MSungbo Eo2019-12-131-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: DTS style improvements for mt7621_wevo_w2914ns-v2.dtsiAdrian Schmutzler2019-12-133-14/+7
| | | | | | | | | | | | This does several trivial DTS style improvements: - Move device name compatible to DTS files (and fix compatible in 11acnas.dts) - Remove xhci node as status is set to okay in mt7621.dtsi already - 0x0 instead of 0x0000 - Simplify state_default node definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ZIO FREEZIOSungbo Eo2019-12-131-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7603EN - 5GHz: MT7612EN - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1x 3.0 - UART: - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 Notes: - FREEZIO has almost the same board as WeVO W2914NS v2. - Stock firmware is based on OpenWrt BB. MAC addresses in factory partition: 0x0004: WiFi 2.4GHz (label_mac-8) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-4) 0xe000: LAN (label_mac+1) Installation via web interface: 1. Access web admin page and turn on "OpenWrt UI mode". 2. Flash sysupgrade image through LuCI, with the "Keep settings" option OFF. Revert to stock firmware: 1. Perform sysupgrade with stock image. Make sure to NOT preserve settings. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebase, use mt7621_wevo_w2914ns-v2.dtsi] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt305x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-124-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for the following devices as they do not set up a MAC address for ethernet in the first place: - asiarf,awapn2403 - belkin,f7c027 - dlink,dir-615-d - mofinetwork,mofi3500-3gn - prolink,pwh2004 - ralink,v22rw-2x2 - unbranded,wr512-3gn-4m - unbranded,wr512-3gn-8m While at it, make some DT node labels consistent with the label property. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt76x8: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-1/+1
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. While at it, change the partition label for zyxel,keenetic-extra-ii to factory to be consistent with node label and all the other devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1Adrian Schmutzler2019-12-124-358/+137
| | | | | | | The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same, so creating a common DTSI will reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for TP-Link Archer C20iAdrian Schmutzler2019-12-111-0/+4
| | | | | | | | | | | | | | Current OpenWrt MAC setup: eth0 &rom 0xf100 :48 eth0.2 eth0+1 :49 wlan0 (5 GHz) &radio 0x8004 different OUI wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0 Label MAC address corresponds to eth0 (&ethernet). No additional addresses found in hexdump of rom/radio. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove dts-v1 identifier from DTSI filesAdrian Schmutzler2019-12-089-10/+0
| | | | | | | | | | | | | | | | The "/dts-v1/;" identifier is supposed to be put once at the beginning of a device tree file. Thus, it makes no sense to provide it a second time in to-be-included DTSI files. This removes the identifier from all DTSI files in /target/linux. Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is missing for most of the following targets, though: mvebu, ipq806x, mpc85xx, ipq40xx This does not touch ipq806x for now, as the bump to 4.19 is close. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert mediatek,mtd-eeprom from decimal to hex notationAdrian Schmutzler2019-12-083-6/+6
| | | | | | | | | | A small subset of devices uses decimal notation for mediatek,mtd-eeprom in DTS files. Convert to hexadecimal notation to be consistent with all the rest. Also change "0" to "0x0" in the same files for consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: reorganize NETGEAR sercomm boardsDavid Bauer2019-11-245-65/+126
| | | | | | | | | | | | This re-organizes the device-tree files for the Sercomm-manufactured NETGEAR routers. They are now split into two different base-boards, from which the respective model is extended. This partially reverts commit c7842ceaaa27 ("ramips: reorganize DTSI files for Netgear R devices"), which introduced inheritance between two completely unrelated base-boards. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: assign correct key-code to wps buttonsChristian Lamparter2019-11-163-3/+3
| | | | | | | | | | The ASUS WL-330N(3G) and the Edimax RG21S had the reset keycode assigned to the WPS button. This patch changes all three devices to use KEY_WPS_BUTTON in the hopes that this fixes unwanted restarts/ unexpected behavior from the users point of view. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ALFA Network Quad-E4GPiotr Dymacz2019-11-141-0/+232
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM, USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support. Specification: - MT7621A (880 MHz) - 256/512 MB of RAM (DDR3) - 16/32+ MB of FLASH (SPI NOR) - optional second SPI flash (8-pin WSON/SOIC) - 1x microSD (SDXC) flash card reader - 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1 - optional 802.3at/af PoE module for WAN - 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V) - 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM) - RTC (TI BQ32002, I2C bus) with backup battery (CR2032) - external hardware watchdog (EM Microelectronic EM6324) - 1x USB 2.0 Type-A - 1x micro USB Type-B for system serial console (Holtek HT42B534) - 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator) - 3x button (reset, user1, user2) - 1x I2C (4-pin, 2.54 mm pitch) header on PCB - 4x SIM (6-pin, 2.00 mm pitch) headers on PCB - 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB - 1x mechanical power switch - 1x DC jack with lock (24 V) Other: - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board has additional logic circuit for M.2 SIM switching. The 'sim-select' will work only if both SIM slots are occupied. Otherwise, always slot with SIM inside is selected, no matter 'sim-select' value. - U-Boot enables power in all three miniPCIe and M.2 slots before loading the kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) - all three miniPCIe slots have additional 5 V supply on pins 47 and 49 - the board allows to install up to two oversized miniPCIe cards (vendor has dedicated MediaTek MT7615N/D cards for this board) - this board has additional logic circuit controlling PERSTn pins inside miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe slots but setting GPIO22 to high allows PERSTn control per slot, using GPIO23-25 (value is inverted) You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: provide label MAC for ALFA Network Tube-E4GPiotr Dymacz2019-11-141-0/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for ALFA Network R36M-E4GPiotr Dymacz2019-11-131-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform based on MediaTek MT7620A WiSoC. This product is designed for operation with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06) but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses). Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32+ MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227) - 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 2x u.fl antenna connectors (for Wi-Fi) - 8x LED (7 driven by GPIO) - 2x button (reset, wifi) - 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB - 1x I2C (4-pin, 1.27 mm pitch) header on PCB - 1x LED (8-pin, 1.27 mm pitch) header on PCB - 1x DC jack with lock (12 V) Other: - there is a dedicated, 4-pin connector for optional RTC module (Holtek HT138x) with 'enable' input, not available at the time of preparing support for this board - miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a jumper resistor (R174) is not installed by default - U-Boot selects default SIM slot, based on value of 'default_sim' env variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will work only if both slots are occupied, otherwise U-Boot will always select slot with SIM card inside (user can override it later, in user-space) - U-Boot resets the modem, using PERSTn signal, before starting kernel - this board supports 'dual image' feature (controlled by 'dual_image' U-Boot environment variable) Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the modem LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: change status LED of Samsung CY-SWR1100Sungbo Eo2019-11-131-4/+6
| | | | | | Use power LED for status indication and free WPS LED for other uses. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: improve Samsung CY-SWR1100 supportSungbo Eo2019-11-131-5/+9
| | | | | | | | | | | | | | | | | | | | | | This patch does the following: - rename "devdata" flash partition and make it read-only - switch from gpio-keys-polled to gpio-keys - add missing power LED - set correct PCI ID to compatible string in wifi node - remove ralink,5ghz property in wifi node - provide label MAC address Rename devdata partition to devconf as indicated in the stock firmware partition table: 00030000-00040000: "devdata" 00040000-00050000: "devconf" Power LED can be controlled by SoC GPIO. Add it in the dts leds node. RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: correct Netgear WNDR3700v5 button flagDavid Bauer2019-11-101-3/+3
| | | | | | | | | This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate the base board is identical to the one of the R6220. Fixes commit 3459013257e0 ("ramips: correct R6220 button flag") Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: correct R6220 button flagDavid Bauer2019-11-091-3/+3
| | | | | | | | | | | | | | All buttons on the Netgear R6220 are active-low while they are flagged as active-high. The GPIO status reads the following for no buttons pressed: root@64367-r6220:~# cat /sys/kernel/debug/gpio gpio-7 ( |wps ) in hi gpio-8 ( |wifi ) in hi gpio-14 ( |reset ) in hi Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3Adrian Schmutzler2019-11-083-162/+104
| | | | | | | | | This moves shared code of the named devices into a common DTSI. Remove setting status="okay" for &gpio0 as it's not disabled in mt7620a.dtsi. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: increase max SPI frequency to 50 MHz for EX3700/EX6130Frederik Noe-Sdun2019-11-081-1/+1
| | | | | | | | | Based on Macronix MX25L3205DM2I datasheet this is maximum supported speed. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, improved commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear EX6130Frederik Noe-Sdun2019-11-083-113/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. The device seems to use base PCB as EX3700/EX3800, but supporting AC1200 using MT7612E. MAC adresses: 5.0 GHz 0x8004 *:9a 2.4 GHz 0x4 *:9b lan 0x28 *:9b wan 0x2e *:9c Since this is a one-port device, although wan MAC address is set in flash, it is not used in OpenWrt setup. Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com> [rebased, extended commit message, tiny DTS style fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rename keys node formerly named buttonAdrian Schmutzler2019-11-073-3/+3
| | | | | | | For some devices, the keys node is named "button". Change name to match the rest of the target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: reorganize DTSI files for Netgear R devicesAdrian Schmutzler2019-11-068-217/+141
| | | | | | | | | This reorganizes DTSI files for the Netgear R devices in mt7621 (and the WNDR3700 v5). It creates a common DTSI for all R (sercomm) devices and distributes the remaining code in r6220.dtsi to R6220 and WNDR3700 v5. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve support for WeVO 11AC NAS and W2914NS v2Sungbo Eo2019-11-061-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | - remove WAN port index - load WAN MAC address directly from the flash - provide label MAC address - increase flash's SPI frequency to 80MHz - add mt76 led nodes to make WiFi LEDs work - drop unnecessary pinmux groups The factory partition scheme for MAC addresses (verified on both devices): 0x4 : WiFi 2.4GHz (label_mac-9) 0x28 : unused 0x2e : WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-5) 0xe000: LAN (label_mac-1) 0xe006: unused By improving flash speed, `time dd if=/dev/mtdblock3 of=/dev/null bs=64k` has been reduced from 14.51s to 3.11s. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebased] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve netis WF-2881 supportSungbo Eo2019-11-061-12/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch does the following: 1. remove u-boot-env partition Stock bootloader saves env variables at 0x80000 in flash, and there is nothing stored at 0x30000. By merging the partition "u-boot-env" with "u-boot", the partition table becomes the same as used in stock firmware: 00000000-00080000: "Bootloader" 00080000-00100000: "Config" 00100000-00140000: "Factory" 00140000-07f80000: "Kernel" 2. fix LAN/WAN MAC addresses and provide label MAC address Ethernet MAC addresses are stored in factory partition at: 0xe000: LAN (label_mac) 0xe006: WAN (label_mac+1) 3. fix LAN port order WF-2881 LAN ports are in reverse order of switch ports. 4. fix WiFi LEDs mt76 led nodes are added to make WiFi LEDs work. On top of this, mt76 node names are changed to more generic ones, and compatible strings are also added. 5. fix pinmux groups uart3 and uart2 pins are used as button and led, but jtag pins are not. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix MTK_SOC for RT3662 devicesSungbo Eo2019-11-046-6/+6
| | | | | | | | | | | rt3883.mk contains both RT3662 and RT3883 device profiles, but commit 6a104ac77206 set MTK_SOC to rt3883 for all devices. This patch fixes it, and renames dts files accordingly. And SoC compatible strings are also appended in the dts. Fixes: 6a104ac77206 ("ramips/rt288x,rt3883: Name DTS files based on scheme") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ZBT WE1026-HKristian Evensen2019-11-032-0/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * When binding the USB LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [rebased onto base-files split, minor style fixes, removed use of USB led as power LED] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: update ZBT WE1026 DTS-filesKristian Evensen2019-11-033-160/+113
| | | | | | | | | | | | | | | | | | | | | | This commit makes the following changes to the WE1026 DTS-files: * The parts that are unique to the -5G-version (LED and 5GHz wifi) are moved to a separate file, so that WE1026.dtsi can be referenced also by the DTS for the -H version. * Use the generic "flash"-name for the spi-nor node. * Add label MAC. All changes have been tested on the WE1026-5G-16M and work fine. I.e., the device works as before the DTS-changes. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Mathias Kresin <dev@kresin.me> Acked-by: Alex Maclean <monkeh@monkeh.net> Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Petr Štetiar <ynezz@true.cz> [minor style fixes, rebased onto base-files split, remove obsolete gpio-keys comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add newline for ASUS RT-ACx5P DTSesAdrian Schmutzler2019-11-032-2/+2
| | | | | | Those files are missing the newline at the end. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2Paul Fertser2019-10-271-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - CMIIT ID: 2019AP2581 - SoC: MediaTek MT7621 - Flash: 16MiB NOR SPI (GigaDevice GD25Q128B) - RAM: 128MiB DDR3 (ESMT M15T1G1664A) - Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset INSTALLATION: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware (looks like an illegal OpenWrt fork) won't accept any serial input unless "uart_en" is set to "1". Tricks to force u-boot to use default environment do not help as it's restricted in the same way. With bootloader unlocked the easiest way would be to TFTP the sysupgrade image or to sysupgrade after loading an initramfs one. For porting the flash contents were changed externally with an SPI programmer (after lifting Vcc flash IC pin away from the PCB). Forum thread [0] indicates that this device is identical to "Xiaomi Mi Router 4A Gigabit Edition". [0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ramips: remove phy0tpt trigger from RT-AC65P/RT-AC85P power LEDAdrian Schmutzler2019-10-271-1/+0
| | | | | | | | | | | | This patch removes a phy0tpt trigger from the power LED, which seems to have been added by mistake. WiFi LEDs using phy0radio and phy1radio triggers are present and used correctly. Cc: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-eeprom in mt76x8 DTS filesAdrian Schmutzler2019-10-278-9/+0
| | | | | | | | | | In mt7628an.dtsi, calibration data for wmac is already defined: mediatek,mtd-eeprom = <&factory 0x0>; Thus, this patch removes redundant entries of this property in derived DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-mac-address for WiFiAdrian Schmutzler2019-10-273-4/+1
| | | | | | | | | | When caldata locations are defined with mediatek,mtd-eeprom the MAC address is automatically read from offset +4. Thus, specifying that location explicitly is redundant. This patch removes those redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Asus RT-AC65PGabor Varga2019-10-243-155/+170
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it. On both routers the installation can be done also via SSH: Note: The user/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt factory image via scp: > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.50.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux 6. Reboot the router > reboot Changelog: v3: removed [] from filename, rebased to latest master v2: Rebased to latest master v1: Initial release Signed-off-by: Gabor Varga <vargagab@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 23:00:24 +0000