aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mvebu/image
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: LS421DE: use automatic fan control with thermal zonesDaniel González Cabanelas2020-07-041-2/+3
| | | | | | | | | | | | | | | | The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal hard drives. Currently there is no control over this fan, running always at fixed medium speed. With the recent jump to the kernel 5.4, now we can monitor the hard drive temperature and control the fan with thermal zones. Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the dts file to allow automatic fan control by the kernel. Tested succesfully using a single Crucial BX500 SSD drive. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* mvebu: move definition of factory.img out of Device/DefaultAdrian Schmutzler2020-06-282-1/+4
| | | | | | | | | | The Device/Default definition in mvebu defines an IMAGE/factory.img which is not included in IMAGES, and only used twice in the individual definitions. Move it out of the default definition to keep it closer to the reassignment of IMAGES and make it more consistent with respect to other values of IMAGE/factory.img Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-111-11/+1
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: remove ClearFog Pro SUPPORTED_DEVICESDENG Qingfang2020-06-051-1/+0
| | | | | | | | | | A direct upgrade from previous swconfig version with incompatible settings to DSA will break the internet. Remove SUPPORTED_DEVICES so users cannot upgrade directly. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [rebase after Linksys rename, adjust title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: rename Linksys devices based on their common namesPaul Spooren2020-06-051-10/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys devices in mvebu target feature a mixed naming, where parts are based on the official product name (device node, image; e.g. WRT3200ACM) and parts are based on the internal code name (DTS file name, compatible, LED labels; e.g. rango). This inconsistent naming has been perceived as quite confusing. A recent attempt by Paul Spooren to harmonize this naming in kernel has been declined there. However, for us it still makes sense to apply at least a part of these changes locally. Primarily, this patch changes the compatible in DTS and thus the board name used in various scripts to have them in line with the device, model and image names. Due to the recent switch from swconfig to DSA, this allows us to drop SUPPORTED_DEVICES and thus prevent seamless upgrade between these incompatible setups. However, this does not include the LED label rename from Paul's initial patch: I don't think it's worth keeping the enormous diff locally for this case, as we can implement this much easier in 01_leds if we have to live with the inconsistency anyway. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, extend to all devices, drop DT LED changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: remove swconfig packageDENG Qingfang2020-06-031-2/+2
| | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* mvebu: tidy up support for GL.iNet GL-MV1000Adrian Schmutzler2020-04-271-9/+8
| | | | | | | | | | | | | | | | | This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000: - apply alphabetic sorting in multiple files - use armada-3720 prefix for DTS like for other devices - fix vendor capitalization for model in DTSes - remove trivial comment in DTS files - use DEVICE_VENDOR/DEVICE_MODEL - remove redundant SUPPORTED_DEVICES - use SOC instead of DEVICE_DTS - remove empty line at EOF Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: add support for GL.iNet GL-MV1000Li Zhang2020-04-261-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for GL-MV1000. Specification: - SOC: Marvell Armada 88F3720 (1GHz) - Flash: 16MB (W25Q128FWSIG) - RAM: 1GB DDR4 - Ethernet: 3x GE (1 WAN + 2 LAN) - EMMC: 8GB EMMC (KLM8G1GETF-B041) - MicroSD: 1x microSD slot - USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC) - Button: 1x reset button,1x slide switch - LED: 3x greed LED - UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND) Update firmware instructions ============================ In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web. Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [Copied dts file to files-5.4] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for Buffalo LinkStation LS421DEDaniel González Cabanelas2020-04-132-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707-A1 CPU: Cortex-A9 1200 MHz, 1 core Flash: SPI-NOR 1 MiB, NAND 512 MiB RAM: DDR3 512 MiB Ethernet: 1x 10/100/1000 Mbps USB: 1x 2.0, 1x 3.0 SATA: 2x 3.0 Gbps LEDs/Input : 5x / 2x (1x button, 1x slide-switch) RTC: Ricoh RS5C372A, I2C, no battery Flash instruction (UART+TFTP): 1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13) 2. Remove any hard drive from inside the bays. 3. Boot the Openwrt initramfs image using the U-Boot serial console: tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin bootm 0x1200000 4. Flash the sysupgrade image using the Openwrt console: sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin 5. Wait until it finish, the device will reboot with Openwrt installed on the NAND flash. Note: - Device shuting down doesn't work, even if the power slide switch is used. We must first, via MDIO, set the unused LED2 at the ethernet phy0 to off state. Reboot works ok. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-1/+1
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: make kmod-i2c-mux selected by dependent modulesSungbo Eo2020-03-162-2/+2
| | | | | | | | | | | | Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to "select", we do not have the issue anymore. Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES and similar variables, as it is now pulled by dependent modules such as: - kmod-i2c-mux-pca954x Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: make kmod-i2c-core selected by dependent modulesSungbo Eo2020-03-132-2/+2
| | | | | | | | | | | | | | | | | | Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to "select", we do not have the issue anymore. Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES and similar variables, as it is now pulled by dependent modules such as: - kmod-hwmon-lm75 - kmod-i2c-gpio - kmod-i2c-gpio-custom - kmod-i2c-mux - kmod-i2c-ralink Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: uDPU: drop patch compiling dtbTomasz Maciej Nowak2020-03-011-1/+1
| | | | | | | | | If device recipe has specified DEVICE_DTS variable, the dtb is built anyway by OpenWrt buildroot image rules. Drop the patch and adjust the location of compiled dtb. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: rework uDPU-firmware recipeTomasz Maciej Nowak2020-03-011-3/+9
| | | | | | | | | Tar has ability to change current dir, so use that instead additional command invocation. Also being here, change tar arguments to make final archive reproducible. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: uDPU: clean package selectionTomasz Maciej Nowak2020-03-011-3/+1
| | | | | | | | | This device receipe selects bunch of packages which some are re-defined, unnecessary or irrelevant. Clean them up, so only basic functionality persist. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: keep global DTS_DIR intactTomasz Maciej Nowak2020-03-011-1/+2
| | | | | | | | Don't rewrite global DTS_DIR, instead, use proper variable for specifying devices dts directory. For consistency, also specify the variable in default profile, as suggested by Adrian Schmutzler. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: align subtargets makefile namesTomasz Maciej Nowak2020-02-014-3/+3
| | | | | | | Align subtargets makefiles names to actual subtargets. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: sort devices alphabeticallyTomasz Maciej Nowak2020-02-012-114/+114
| | | | | | | | This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: use SOC to derive DEVICE_DTSAdrian Schmutzler2020-01-213-7/+8
| | | | | | | | | | | | This introduces the SOC variable to mvebu target to derive some of the DEVICE_DTS variables based on the SOC prefix and the device definition name. Since DTS names and compatible are inconsistent also in the kernel for this target, the scheme cannot be applied to all devices, though. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: move subtarget image Makefile switch to parent MakefileAdrian Schmutzler2020-01-214-12/+8
| | | | | | | | | | This moves the if conditions for choosing which image Makefiles are used to the parent image/Makefile. It seems more convenient to have "codeflow" in the parent while the subtarget-specific files only contain the definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: gen_mvebu_sdcard_img.sh: use /bin/shRosen Penev2019-12-311-1/+1
| | | | | | | | There is nothing that needs bash anymore. Signed-off-by: Rosen Penev <rosenp@gmail.com> [add prefix to commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: gen_mvebu_sdcard_img.sh: don't use format directly in printfRosen Penev2019-12-311-1/+1
| | | | | | | | | | Enables proper checking. Matches printf behavior in C. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com> [add prefix to commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: gen_mvebu_sdcard_img.sh: replace let with $(())Rosen Penev2019-12-311-1/+1
| | | | | | | | | | let is a bashism. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com> [add prefix to commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* x86,tegra,mvebu: image: use common reproducible IMG_PART_SIGNATUREPaul Spooren2019-11-111-5/+3
| | | | | | | | | | | | | These targets are currently using more or less same SIGNATURE variable which provides unique partition ID/signature, so it makes sense to refactor it out into common IMG_PART_SIGNATURE variable which could be reused by all targets. This is another step in the direction of reproducible OpenWrt images. Signed-off-by: Paul Spooren <mail@aparcar.org> [split into separate commit, renamed to IMG_PART_SIGNATURE] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* build: label kernel and rootfs ext4 volumesYousong Zhou2019-11-031-1/+1
| | | | | | | | | | | UUID of ext4 volumes generated by make_ext4fs are determined by volume label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label is empty Labeling them does not make them unique but tools like block command from fstools have a better chance differentiating them Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* mvebu: split up DEVICE_TITLEMoritz Warning2019-10-193-27/+90
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* treewide: replace backticks by $(...) in gen_*_img.sh scriptsAdrian Schmutzler2019-09-291-1/+1
| | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [decapitalized patch subject at submitter's request] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mvebu: uDPU: add sysupgrade supportVladimir Vid2019-08-243-3/+54
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds sysupgrade, uboot-env and networking support for Methode uDPU device. Device features 4 partitions: ----------------------------------------- | boot | recovery | rootfs | misc | | (ext4) | (ext4) | (fsf2) | (f2fs) | _________________________________________ Idea was to use f2fs only but the u-boot currently lacks support so first 2 partition are ext4 to be u-boot readable, and this was a reason why custom build and sysupgrade sections were required. On the sysupgrade, boot and rootfs partitions are updated, firmare image and user configuration is saved on the misc partition and if the upgrade was successfull, recovery partition will be updated on after the reboot from preinit script. If the sysupgrade fails for any reason, device will fallback to recovery initramfs image. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mvebu: add initial support for uDPU boardVladimir Vid2019-06-281-0/+13
| | | | | | | | | | | | | | | | | | | This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point unit made by Methode Electronics which offers complete modularity with replaceable SFP modules both for uplink and downlink (G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable). On-board features: - 512 MiB DDR3 - 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC - USB 2.0 Type-C connector - 4GB eMMC - ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type) uDPU is intented to run on kernel 4.19 on newer due to the SFP and hardware support. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mvebu: image: fix generic-arm64.bootscript mmc selectionVladimir Vid2019-06-181-2/+8
| | | | | | | | | | Not all versions of ESPRESSObin require SD card, but can be booted from the internal emmc flash (mmc dev 1) instead. Add a simple check in the bootscript to see which mmc device is detected and boot from it using mmcdev variable. Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mvebu: add kmod-i2c-mux-pca954x for Turris OmniaJosef Schlehofer2019-05-151-1/+1
| | | | | | | | The driver is for the I2C mux. Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz> Tested-by: Rosen Penev <rosenp@gmail.com>
* mvebu: add images for additional ESPRESSObin boardsTomasz Maciej Nowak2019-05-111-0/+21
| | | | | | | | | | | | | | | | | | | | | This commit adds support for different iterations of ESPRESSObin. The added variants are: ESPRESSObin with soldered eMMC, ESPRESSObin V7, compared to V5 some passive elements changed and ethernet ports labels positions have been reversed, ESPRESSObin V7 with soldered eMMC. Please refer to: 584d7c5 ("mvebu: new subtarget cortex A53") for instruction how to boot OpenWrt image placed on SD card. It is advised for owners of V5 and previous with bootloader based on U-Boot 2015.01, to upgrade the latest version available at: http://espressobin.net/tech-spec. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: use device-tree board detectionTomasz Maciej Nowak2019-05-114-8/+18
| | | | | | | | Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: align device names to vendor_device formatTomasz Maciej Nowak2019-05-114-46/+51
| | | | | | | | | | Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: don't create unnecessarily shell variablesTomasz Maciej Nowak2019-05-112-14/+8
| | | | | | | Use make syntax to pass the U-Boot image location and boot with root partitions size, instead of relying on shell functions and variables. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: improve readability of device recipesTomasz Maciej Nowak2019-05-112-41/+19
| | | | | | | | Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: introduce BOOT_SCRIPT variableTomasz Maciej Nowak2019-05-117-57/+12
| | | | | | | | | | | | All of U-Boot scripts repeat the same pattern with only Device Tree blob name changing for respective device. Therefore create generic scripts which will be altered on demad by image build process, and create BOOT_SCRIPT variable which can be added to device recipe and will allow referencing the same script by many device recipes. This will allow to slim down the ammount of files in buildroot tree and avoid needlessly incrementing amount of boot scripts if new devices will be added. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: stack repeated variablesTomasz Maciej Nowak2019-05-113-25/+15
| | | | | | | All of arm64 devices have part of variables repeatedly defined. Stack them to common define, and reference it in each device recipe. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: remove unnecessary code building dtbsTomasz Maciej Nowak2019-05-111-7/+3
| | | | | | | | | Even if dts is not included in upstream Makefile, it is built anyway by recipe specified in include/image.mk. Also remove Build/dtb, it's not used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in image"). Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: sysupgrade: sdcard: keep user added partitonsTomasz Maciej Nowak2019-04-061-3/+4
| | | | | | | | Currently sysupgrade overwrites whole disk and destroys partitions added by user. Sync the sysupgrade code with the one present in x86 target to remedy this behaviour. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: shrink amount of packages and reorganize themTomasz Maciej Nowak2019-04-063-7/+3
| | | | | | | | | Since most of devices using SD card image to boot, use ext4 as boot files system we can drop fat fs related packages. Also move packages which are added repeatedly across subtargets to their default packages, with droping the ones that are enabled in target kernel configugation. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: use ext4 for clearfog image bootfsTomasz Maciej Nowak2019-04-061-2/+2
| | | | | | | This will allow to drop additional packages and shrink image size. Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: make bootfs size for sdcard image configurableTomasz Maciej Nowak2019-04-061-10/+6
| | | | | | | Let's take this oportunity to implement boot-part and rootfs-part feature flags. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: Add dependency to kmod-i2c-mux-pca954x for armada-macchiatobinHauke Mehrtens2019-03-261-1/+1
| | | | | | This driver is needed for the I2C mux on the board. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-2/+2
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-261-1/+1
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* mvebu: initial support for Marvell Armada 7k and 8k DB boardsDamir Samardzic2018-05-211-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for cortex-a72 based Armada DB-88F8040-Modular and DB-88F7040-Modular development boards. DB-88F8040-Modular specifications: - Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz) - DDR4 DIMM - 64 bits + ECC - 2 x 128 Mb SPI NOR flash memory - 2 x 1G Ethernet port via RGMII (RJ45) - 2 x SD card ports (4 bit port on CP, 8 bit port on AP) - 2 SERDES modules with the following interfaces each: - 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0 via SERDES Module CON2 or CON1 (optional port)) - 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port), Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6 (optional port)) - 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and CON10) - 1 x 10G port over SFP+ connector (via SERDES module CON8) - 1 x MCI interface by two over USB Type C connector - 4 x serial COM port driven by the 88F8040 UART interface and converted to USB via FTDI IC - I2C Master Interface - CP I2C 2x EEPROM @ Address 0x50 and 0x57 - 1 x I/O Expander @ Address 0x21 - Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E - I2C Slave Interface (via SERDES module) - Connection to each device on the board via an I2C multiplexer - JTAG interface for CPU emulator - Board dimensions: 270 mm x 240 mm (main + SERDES module) - SERDES Module Dimensions: 70 mm x 105 mm DB-88F7040-Modular specifications: - Quad-core ARMv8 Cortex A72 CPU - CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad Core - DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte 32-bit - 1 x 128Mb SPI NOR flash memory - 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII - SD card 4 bits port on AP - eMMc Module on CP - 1 SERDES Modules with the following interfaces each: - 1 x SATA Rev 3.0 port (via SERDES module CON4) - 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5) - 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and CON10) - 1 x 10G port over SFP+ connector (via SERDES module CON8) - 2 x MCi interface by one over USB Type C connector - 4 x Serial COM port driven by the 88F7040 UA - RT interface and converted to USB via FTDI IC - I2C Master Interface - 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57 and 0x50 in CP - 1 x I/O Expander at address 0x21 - Sample at Reset (SatR) memory device at address 0x4C and 0x4E - I2C Slave Interface (via SERDES module) - Connection to each device on the board via an I2C multiplexer - JTAG interface for CPU emulator - Board dimensions - 270 mm x 240 mm (main + SERDES module) - SERDES Module Dimensions - 70 mm x 105 mm Booting from USB flash drive (dd sdcard image to the flash drive): 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot manually (make sure to set correct dtb file name): setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp' setenv fdtfile armada-7040-db.dtb setenv image_name Image setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr' saveenv boot Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: initial support for Marvell Armada 3720 DB boardDamir Samardzic2018-05-212-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Marvell Armada cortex-a53 based DB-88F3720-DDR3-Modular development board. Specifications: - Dual core ARMv8 Cortex-A53 CPU (up to 1.0 GHz) - 4Gb 16-bit DDR3/3L DRAM memory - 128Mb SPI NOR flash memory - 8Gb eMMC NAND flash memory - 1 x SATA Rev 3.0 port - 1 x PCI Express (PCIe) Gen 2.0 or 1 x mini PCI Express (PCIe) Gen 2.0 - 1 x 1G Ethernet port via RGMII (RJ45) - 1 x SD card port - 1 x USB3 (USB2 backward) host\device port via type C connector - 1 x USB2 host port via type A connector - 1 x serial COM port driven by the 88F3720 UART interface and converted to USB via FTDI IC (option to connect the UART DB9 adapter) - I2C Master Interface: - 1 x EEPROM @ address 0x57 - 1 x I/O Expanders @ address 0x22 - Sample at Reset (SatR) memory device @ address 0x4C - RTC clock generator PT7C4337AWE @ address 0x68 - USB3 switch PI5USB30213XEA @ address 0x0D - ID component of PHY module @ address 0x24 - 1 x JTAG interface for CPU emulator - 1 x SETM and JTAG debug interface - 1 x power connector for HDD supply - 1 x 12V DC jack power connector - Board dimensions: 150 mm x 179 mm - LED interface for system status Booting from SD card: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually: setenv fdt_name armada-3720-db.dtb setenv image_name Image setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: add support for WRT32X (venom)Michael Gray2018-05-141-0/+10
| | | | | | | | | | | | | | | | | | Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* mvebu: add support for MACCHIATObin (cortex-a72)Damir Samardzic2018-03-313-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell ARMADA 8040 Community board. Comes in two forms: Single Shot and Double Shot. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) via copper or SFP 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Booting from micro SD card: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually: setenv fdt_name armada-8040-mcbin.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-15 02:12:58 +0000