aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mpc85xx/image
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-131-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: disable initramfs image in TL-WDR4900Pawel Dembicki2019-01-131-0/+1
| | | | | | | | | | Initramfs image isn't required for this device and regular initramfs generation isn't work properly. It create not working binaries. This patch disable initramfs image for TL-WDR4900. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mpc85xx: add support for Freescale (NXP) P2020RDBPawel Dembicki2019-01-131-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit add initial support for Freescale (NXP) P2020RDB Hardware: SoC: P2020 2x1GHz DRAM: 512-1GB DDR3 2 + 4 GBE (2 separate ports and four in VSC7385) Flash: 16MB NOR, 32MB NAND, 16MB SPI-NOR PCIE x1 and mPCIE x1 SD Reader Interfaces: GBE RJ45 x6 USB2.0 x1 UART x2 I2C x2 JTAG x1 SD x1 PCIE x2 (PCIE and mPCIE) Flash instructions: Place sysupgrade image to 0x80000 address in NOR. Eg. (no brakelines in setenv command): setenv 'firmware_flash tftpboot $loadaddr $firmwarefile; protect off $norfdtaddr +$filesize; erase $norfdtaddr +$filesize; cp.b $loadaddr $norfdtaddr $filesize; protect on $norfdtaddr +$filesize; cmp.b $loadaddr $norfdtaddr $filesize' setenv firmwarefile firmware.bin run firmware_flash Boot (no brakeline in setenv command): setenv bootcmd 'setenv bootargs root=/dev/mtdblock3 rw console=$consoledev, $baudrate rootfstype=squashfs $othbootargs; bootm $norfdtaddr' saveenv boot Known issues: -Switch is unmanaged (VSC 7385 is connected via eLBC, driver uses SPI) -No SD reader support Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed patches]
* mpc85xx: tl-wdr4900-v1: convert to mtdsplit imagePawel Dembicki2019-01-051-13/+26
| | | | | | | | | | | | | | | Currently, the image creation process for the TP-Link tl-wdr4900-v1 needs a fixed sized kernel and places the rootfs partition at a fixed offset. With the upcoming move to 4.19 the kernel will no longer fit into the existing allocated space for the kernel partition. This patch converts the device to utilize the established tplink,firmware mtdsplitter, which can deal with a dynamic kernel/rootfs size. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-2/+2
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-11/+1
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use image metadataMathias Kresin2017-10-251-2/+4
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use new build code styleChris Blake2017-10-251-83/+53
| | | | | | | | | | The following moves the mpc85xx target (generic & P1020) to the new build code style. Compile & Flash tested on an Aerohive HiveAP-330. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: Add Aerohive HiveAP-330 Access PointChris Blake2017-10-141-1/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive HiveAP-330 Access Point to LEDE under the mpc85xx/p1020 subtarget. Hardware: - SoC: Freescale P1020NSE2DFB - NAND: Intel JS28F512M29EWH 64MB - Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - 5.0GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - Eth2: Atheros AR8035-A - TPM: Atmel AT97SC3204 - LED Driver: TI LP5521 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; tftpboot 0x1000000 192.168.1.101:lede- mpc85xx-p1020-hiveap-330-initramfs.zImage; tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt; bootm 0x1000000 - 0x6000000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NAND. sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* target/mpc85xx: check for 'generic' subtarget for initramfs image fileJohn Crispin2016-03-031-0/+2
| | | | | | | | | | | | | Copy 'cuImage.tl-wdr4900-v1-initramfs' only for the 'generic' subtarget. This is a follow-up to: http://git.openwrt.org/?p=openwrt.git;a=commitdiff;h=b889fe55c1844aec2c03da28fecb03e958c21f18 We build our initramfs images more rarely, so it took a while to catch this too. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com> SVN-Revision: 48892
* mpc85xx: update to linux 4.4, remove unnecessary patchesFelix Fietkau2016-01-171-2/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48297
* mpc85xx: fix another typo in the image makefileFelix Fietkau2014-12-111-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43625
* mpc85xx: fix typo in image nameFelix Fietkau2014-12-111-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43622
* mpc85xx: fix initramfs imagesFelix Fietkau2014-12-111-8/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 43620
* mpc85xx: fix missing dts target for kernel 3.14John Crispin2014-11-241-1/+1
| | | | | | | | | | With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa. To maintain compatibility define p1010rdb-pa as new standard and copy p1010rdb.dts to p1010rdb-pa.dts under 3.10. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 43371
* target/linux/*/image/Makefile: use new dts path variableJohn Crispin2014-07-211-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41791
* mpc85xx: Fix building ramdisk imagesGabor Juhos2014-01-231-6/+2
| | | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39368
* targets: prepare for supporting normal and initramfs imagesFlorian Fainelli2013-06-271-1/+1
| | | | | | | | | | | | In order to support both normal images and initramfs, ensure that each target sets KERNELNAME properly so that the generic kernel building code can copy the corresponding files over $(KDIR) with the appropriate extension. Update the various paths to the kernel and wrapper images from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo). Signed-off-by: Florian Fainelli <florian@openwrt.org> SVN-Revision: 37049
* mpc85xx: Generate fdt for P1020RDBGabor Juhos2013-04-121-1/+1
| | | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36321
* mpc85xx: add profile and build image for the TL-WDR4900 v1 boardGabor Juhos2013-03-151-3/+45
| | | | | | | | | Now that the ethernet switch is working, create firmware images to make impatient users happy. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36051
* mpc85xx: use a foreach loop to copy boot imagesGabor Juhos2013-02-201-1/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35689
* mpc85xx: enable squashfs featureGabor Juhos2013-02-191-0/+5
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35675
* mpc85xx: switch to 3.6Gabor Juhos2013-02-011-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35444
* mpc85xx: fix dts name for P1010RDBGabor Juhos2013-02-011-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35442
* mpc85xx: build fdt file for the PB1010RDB boardGabor Juhos2013-02-011-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35438
* mpc85xx: image: fix building of multiple dtb filesGabor Juhos2013-02-011-1/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35436
* mpc85xx: copy the fdt for mpc8548cds to $(BIN_DIR)Felix Fietkau2011-03-161-0/+3
| | | | SVN-Revision: 26191
* preliminary support for Freescale MPC85xx based boardsImre Kaloz2010-12-051-0/+26
SVN-Revision: 24259
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-05 07:51:06 +0000