aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mpc85xx/config-4.19
Commit message (Collapse)AuthorAgeFilesLines
* kernel: remove support for kernel 4.19Adrian Schmutzler2020-10-301-323/+0
| | | | | | | We use 5.4 on all targets by default, and 4.19 has never been released in a stable version. There is no reason to keep it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* treewide: Don't diverge from upstream default HZ settings on 4.19Daniel Engberg2020-03-291-3/+0
| | | | | | | | | | | Most targets upstream use 250Hz or even 1000Hz by default while 100Hz is hardcoded in OpenWrt's default config. Use upstream default except for apm821xx which hardsets 1000Hz instead of platform default of 250Hz. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [Apply same changes to 5.4] Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mpc85xx: move NAND symbol to target configDavid Bauer2020-02-291-0/+2
| | | | | | | | | All mpc85xx subtargets utilize NAND, thus enable NAND support target-wide. Fixes: 1287bb48dc72 ("mpc85xx: fix build with kernel 5.4") Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Enterasys WS-AP3710iDavid Bauer2019-12-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-091-2/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: remove USB support from kernelDavid Bauer2019-04-131-7/+0
| | | | | | | | | | | | This removes USB support from the compiled kernel. Because of this, the kernel is just small enough for the TP-Link WDR4900 to boot the resulting kernel. This is necessary to support the WDR4900 in the upcoming 19.xx release. In the long run, this should be fixed with a second stage bootloader, as the vendor bootloader only loads the first 2684k bytes. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: 4.19: add missing symbolPawel Dembicki2019-02-141-0/+1
| | | | | | | | OCEDO Panda was added in b368373f, but only for 4.14 config. This patch fix 4.19 build for generic and p2020 subtarget. Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: 4.19: refresh kernel configChristian Lamparter2019-01-051-67/+29
| | | | | | | This patch syncs the 4.19 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add kernel 4.19 supportPawel Dembicki2019-01-051-0/+369
Copied config from 4.14 Add patches for 4.19 Drop patch 103-powerpc-fix-build-cross32ar.patch, because issue was fixed in upstream. Compiled: generic p1020 Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]