aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/image
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: add support for reyee AX3200-E5Alex Hansen2022-12-061-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly different flash layout, install process is the same. Specifications: SoC: MT7622B RAM: 256MB Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR Ethernet: 5x1GbE Switch: MT7531BE WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) 2Keys: Mesh button + Reset button UART: Marked J19 on board. 3.3v, 115200n1 Power: 12V 2.5A Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Alex Hansen <mralexh123@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: drop the use of device tree overlays on mt7986a-rfb boardFelix Fietkau2022-11-091-8/+7
| | | | | | | The boot loader does not support it. Instead make NAND the default image for this board Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add Xiaomi Redmi Router AX6000 supportChukun Pan2022-10-301-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128 MB RAM: K4A4G165WF-BCWE 512 MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7976GN 2.4GHz ax 4x4 WiFi2: MT7976AN 5GHz ax 4x4 Button: Mesh, Reset Flash instructions: 1. Gain ssh and serial port access, see the link below: https://openwrt.org/toh/xiaomi/redmi_ax6000#installation 2. Use ssh or serial port to log in to the router, and execute the following command: nvram set boot_wait=on nvram set flag_boot_rootfs=0 nvram set flag_boot_success=1 nvram set flag_last_success=1 nvram set flag_try_sys1_failed=8 nvram set flag_try_sys2_failed=8 nvram commit 3. Set a static ip on the ethernet interface of your computer (e.g. default: ip 192.168.31.100, gateway 192.168.31.1) 4. Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server. 5. Interrupt U-Boot and run these commands: setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi) saveenv tftpboot initramfs.bin bootm 6. After openwrt boots up, use scp or luci web to upload sysupgrade.bin to upgrade. Revert to stock firmware: Restore mtdparts back to default, then use the vendor's recovery tool (Windows only). Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: enable thermal, I2C and PWM of the BPi-R3Daniel Golle2022-10-071-1/+1
| | | | | | | Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin GPIO bank) and PWM (1x fan and 1x GPIO bank). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.Yoonji Park2022-09-121-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core) RAM: DDR3 128MB Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB) WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4) UART: [GND, RX, TX, 3.3V] (115200) Installation: - Flash recovery image with TFTP recovery Revert to stock firmware: - Flash stock firmware with TFTP recovery TFTP Recovery method: 1. Unplug the router 2. Hold the reset button and plug in 3. Release when the power LED stops flashing and go off 4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0 5. Flash image with TFTP client to 192.168.0.1 Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
* mediatek: bananapi-r3: remove kmod-btmtkuart from default packagesDaniel Golle2022-09-101-1/+1
| | | | | | | The package kmod-btmtkuart is specific for MT7622 and isn't available for MT7986 (which doesn't have this built-in Bluetooth like MT7622). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix typo in bpi-r64 image recipeDaniel Golle2022-09-081-1/+1
| | | | | | | Janusz Dziedzic reported a typo introduced by a recent commit. Fix it. Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r64: make initramfs/recovery optionalDaniel Golle2022-09-081-2/+7
| | | | | | | | | Only include recovery image in SD card image generated for the BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS This allows to build images larger than 32 MB (the limit for initramfs/recovery image) by deselecting initramfs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r3: make initramfs/recovery optionalDaniel Golle2022-09-081-2/+7
| | | | | | | | | Only include recovery image in SD card image generated for the BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS. This allows to build images larger than 32 MB (the limit for initramfs/recovery image) by deselecting initramfs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Bananapi BPi-R3Daniel Golle2022-08-301-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Bananapi BPi-R3 is a development router board built around the MediaTek Filogic 830 (MT7986A) SoC. The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC. Only either SPI-NAND or SPI-NOR can be used at the same time, also only either microSD or eMMC can be used. The various storage options can be selected using small SMD switches on the board. Specs: * MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53 * 4T4R 2.4G 802.11bgnax (MT7975N) * 4T4R 5G 802.11anac/ax (MT7975P) * 2 GB DDR4 RAM * 8 GB eMMC * 128 MB SPI-NAND flash * 32 MB SPI-NOR flash * on-board MT7531 GbE switch * 2x SFP+ (1 GbE / 2.5 GbE) * 5x GbE network port * miniPCIe slot (only USB 2.0 connected) * uSIM slot (connected to miniPCIe interface) * M.2 KEY-E PCIe interface (PCIe x2) * microSD card interface * 26 PIN GPIO Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3 Working: * all 4 boot methods incl. installation via U-Boot, sysupgrade, ... * copper LAN and WAN ports * SFP1 (connected to gmac1, eth1 in Linux) * WiFi * LEDs * Buttons * PSTORE/ramoops based dual-boot Not Working (missing driver features): * SFP2 (connected to MT7531 switch) Untested: * M.2/NGFF slot (PCIe x2) * mPCIe slot (USB 2.0 + SIM) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add filogic subtargetFelix Fietkau2022-08-281-0/+51
| | | | | | | | Initially this covers MT7986 only, but it will later be expanded to cover other Filogic branded platforms by MediaTek Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add Ubiquiti UniFi 6 LR v2 targetsHenrik Riomar2022-06-111-0/+29
| | | | | | | | | | | | | | | Add targets: * Ubiquiti UniFi 6 LR v2 * Ubiquiti UniFi 6 LR v2 (U-Boot mod) This target does not have a RGB led bar like v1 did Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration The white dome LED is default-on, blue will turn on when the system is in running state Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* mediatek: new target ubnt_unifi-6-lr-v1-ubootmodHenrik Riomar2022-06-111-4/+5
| | | | | | | | based on current ubnt_unifi-6-lr-ubootmod Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* mediatek: new target mt7622-ubnt-unifi-6-lr-v1Henrik Riomar2022-06-111-3/+5
| | | | | | | | | | | | Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for adding a v2 version of this target * v1 - with led-bar * v2 - two simple GPIO connected LEDs (in later commits) Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
* mediatek: mt7622: add support for ELECOM WRC-X3200GST3INAGAKI Hiroshi2022-05-211-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specifications: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK) - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915A - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J19: 3.3V, GND, TX, RX from power jack side - 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-X3200GST3 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex)) WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex)) 2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:7A (none) Note: - currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in "trigger" file of LEDs, use "phy1radio" trigger instead Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: build ubnt-ledbar as a moduleChuanhong Guo2022-04-301-2/+2
| | | | | | | | The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because of its I2C dependency. Build it as a module and let buildroot handle this config option instead. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: Add support for Xiaomi Redmi Router AX6SRichard Huynh2022-03-201-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com>
* mediatek: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-051-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | X32 Pro is another product name for it in the Chinese market. Specifications: - SoC: MT7622B - RAM: 256MB - Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR - Ethernet: 5x1GbE - Switch: MT7531BE - WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN - 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) - 2Keys: Mesh button + Reset button - UART: Marked J19 on board. 3.3v, 115200n1 - Power: 12V 2.5A MAC addresses as verified by OEM firmware: use address source WAN *:F4 ethaddr@product_info LAN *:F5 5g *:F6 2g *:F7 Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* mediatek: mt7623: simplify partition generationDaniel Golle2022-01-311-6/+1
| | | | | | | | | The two options 'emmc' and 'sdmmc' now became identical lines after introducing CONFIG_TARGET_ROOTFS_PARTSIZE. Remove the now useless if-clauses. Fixes: a40b4d335a ("mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: include regular AHCI PCI driverDaniel Golle2022-01-251-1/+1
| | | | | | | | | The legacy image for the UniElec U7623-02 until now included kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that board uses a PCIe-connected AHCI controller for the SATA port and mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add configuration for UniElec U7623 boardDaniel Golle2022-01-231-5/+5
| | | | | | | Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: rework images for U7623-02 boardDaniel Golle2022-01-236-270/+53
| | | | | | | | | | | | | | | | | | | | | | Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz file once which will upgrade U-Boot and switch to the new image layout. Users of the vendor firmware need to first flash the legacy image to then sunsequently carry out a full-flash upgrade. Alternatively the board can also be flashed using MediaTek's proprietary SP Flash Tool. Configuration as well as persistent MAC address will be lost once at this point and you will have to redo (or restore) all configuration manually. To restore the previous persistent MAC address users may set it manually using fw_setenv ethaddr 00:11:22:33:44:55 For future upgrades once running OpenWrt past this commit, the usual *sysupgrade.itb file can be used. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZEDaniel Golle2022-01-232-4/+4
| | | | | | | Enable 'rootfs-part' feature to make the size of the partition of the production image configurable instead of hard-coding it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rework and fix mt7622-rfb1-ubi supportFelix Fietkau2022-01-131-0/+1
| | | | | | | | Limit bmt remapping range to cover everything up to and including the kernel image, use the rest of the flash area for ubi. Fix partition table and sysupgrade support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add support for TOTOLINK A8000RUChuanhong Guo2021-09-031-0/+10
| | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7622 - RAM: 512MB - Flash: MX35LF1GE4AB 128MB SPI NAND - Ethernet: RTL8367S 5x1GbE - WiFi: 2.4G: MT7622 5G: MT7615N x2 - Other ports: USB3.0 x1 Flash instruction: *important*: upgrade vendor firmware to at least V7.1cu.643_B20200521 1. hold the reset button and power on the device. wait for about 10s before releasing the reset button. 2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: mt7623: yet another legacy image variable restoredDaniel Golle2021-07-211-0/+6
| | | | | | | Restore BOOTFS_BLOCKS variable until U7623 gets brushed, so things hopefully build now. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: allow build without ext4 rootfsDaniel Golle2021-07-211-1/+1
| | | | | | | | | | The image generation code for the U7623 board expects ext4 filesystem to be selected in menuconfig and CONFIG_TARGET_ROOTFS_PARTSIZE to be defined. Now that ext4 isn't enabled any more, the variable was missing and broke the build. Set the default (104) instead of using the config variable to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: add back needed build steps for U7623 boardDaniel Golle2021-07-211-0/+21
| | | | | | | | When reworking the BPi-R2 the mtk-mmc-img build step was removed despite it was still needed to build the image for the UniElec U7623 board. Add it back for now until U7623 gets its facelift. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: drop kmod-mmcDaniel Golle2021-07-201-1/+1
| | | | | | | Support for MMC is built-into the kernel anyway, no need to select the (empty/stub) kmod package. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rework Bananapi BPi-R2Daniel Golle2021-07-203-119/+105
| | | | | | | | | | | | | * introduce recovery (=initramfs) vs. production dual boot scheme * make use of uImage.FIT (instead of FAT partition) * generate images using build steps (instead of external scripts) * simplify sysupgrade and config restore (thanks to uImage.FIT) * make sure mmc devices are ordered persistently (set DT aliases) This commit breaks sysupgrade from existing installations, you will have to re-install using the sdcard.img.gz image. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r64: add eMMC bootloader artifactsDaniel Golle2021-05-011-1/+3
| | | | | | | | In order to allow easily updating the bootloader on eMMC also provide artifacts for that. Support for updating bootloader via TFTP will be added to the loader CLI menu in a follow-up commit. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r64: fix sdcard.img.gz in ImageBuilderDaniel Golle2021-04-231-1/+1
| | | | | | | | Generating the sdcard.img.gz file requires the initramfs/recovery image to be present. Use the newly introduced 'append-image-stage' build command to fix the ImageBuilder for the BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: add spi-nand support for bananapi bpi-r64Oskari Lemmela2021-04-111-1/+5
| | | | | | | | | | Some of bpi-r64 boards have serial NAND attached to SPI bus. Add SD card image support for installing openwrt to it. Default to nand upgrade if root device is not mmc block device. Separate preloader and uboot images for snand are generated. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: bpi-r64: use separate partition for emmc bootloaderOskari Lemmela2021-04-111-6/+7
| | | | | | | eMMC booloader is stored to separate partition. FIP size is increased to 2MB. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: add alternative bootchain variant for UniFi 6 LRDaniel Golle2021-04-091-0/+18
| | | | | | | | Builds images for the Ubiquiti Network UniFi 6 LR device running the U-Boot build added by the previous commits. Everything but MTD partitions is moved to dtsi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: generate complete sdcard image for BPi-R64Daniel Golle2021-03-241-4/+9
| | | | | | | Populate the recovery and production partitions of the generated sdcard image for the Bananapi BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix broken UniFi 6 LR imageDavid Bauer2021-03-181-0/+1
| | | | | | | | Ubiquiti's own bootloader expects the configuration mode to be present with a "@" instead of a "-" for the sperator character. Otherwise booting of the image fails. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: bpi-r64: use dt-overlay to select SATA or PCIE1Daniel Golle2021-03-171-0/+1
| | | | | | | | | | The Bananapi BPi-R64 got a SATA interface which cannot be used at the same time as the second mPCIe slot. The decission is made by hogging GPIO 90. Embed two addtional DT overlay blobs into the image to allow bootloader selection of either SATA or PCIE1 feature. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: drop duplicate DEVICE_PACKAGESDaniel Golle2021-03-151-1/+1
| | | | | | | | kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part of the target's default package set. No need to add them again for buffalo_wsr-2533dhp2. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Buffalo WSR-2533DHP2INAGAKI Hiroshi2021-03-151-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Buffalo WSR-2533DHP2. The device uses the Broadcom TRX image format with a special magic. To be able to boot the images or load them they have to be wrapped with different headers depending how it is loaded. There are multiple ways to install OpenWrt on this device. Boot ramdisk from U-Boot ---------------------------- This will load the image and not write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux to SDRAM via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin 4. The system boots the image Write to flash from U-Boot ----------------------------- This will load the image over tftp and directly write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux Kernel then write to Flash via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin 4. The system writes this image into the flash and boots into it. Write to flash from Web UI ----------------------------- This will load the image over over the Web UI and write it into the flash 1. Open the Web UI 2. Go to "管理" -> "ファームウェア更新" 3. Select "ローカルファイル指定" and click "更新実行" 4. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin 5. The system writes this image into the flash and boots into it. Specifications ------------------- * SoC: MT7622 (4x4 2.4 GHz Wifi) * Wifi: MT7615 (4x4 5 GHz Wifi) * Flash: Winbond W29N01HZ 128MB SLC NAND * RAM 256MB * Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s) Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7622: clean up image buildDaniel Golle2021-03-141-22/+13
| | | | | | | | | | | | | * clean up whitespace to make GPT partitioning more readable * don't select packages already part of the target default selection * don't select U-Boot variants (breaks ImageBuilder) * don't select AHCI on boards without SATA * don't select kmod-usb2 and kmod-ohci, USB 1.x and USB 2.0 devices work fine with the in-SoC XHCI host having just kmod-usb3 installed. * select kmod-btmtkuart for devices with Bluetooth support * sort DEVICE_PACKAGES Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: image: don't use 'M' unit as dd may not support thatDaniel Golle2021-03-131-2/+2
| | | | | | | | | dd on Mac OS X apparently fails when using 'M' unit for bs. dd: bs: illegal numeric value Use 'k' unit instead for 'pad-to' to fix that. Reported-by: Georgi Valkov <gvalkov@abv.bg> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: check firmware metadataDaniel Golle2021-03-041-1/+1
| | | | | | | | | | All mt7622 devices except for the UBI-variant of the mt7622-rfb1 carry metadata appended to the sysupgrade image. Add it for the mt7622-rfb1-ubi as well and check it on sysupgrade to avoid accidentally flashing firmware for the wrong device (or variant or future DEVICE_COMPAT_VERSION). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: change image generationOskari Lemmela2021-03-031-7/+6
| | | | | | | - set only one EFI system partition - use shorter path for DEVICE_DTS file Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: mt7622: use ptgen generated MBR headerOskari Lemmela2021-03-031-2/+2
| | | | | | | mt7622 uses MBR partition for booting from SD card. Add hybrid MBR entry with boot flag after PMBR entry. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: mt7622: make sure image generation can run in parallelDaniel Golle2021-03-021-8/+7
| | | | | | | | The previous approach of referencing artifacts in follow-up artifacts can't work with parallel builds in the current way image.mk is built. Refactor things so this is not needed. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: bpi-r64: simplify eMMC install procedureDaniel Golle2021-03-011-5/+4
| | | | | | | | Write everything needed for eMMC install into the gaps between partitions on SD card. In that way, installation to eMMC only needs the SD card, no additional files need to be loaded via TFTP any more. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: rename mt7622-ubi to mt7622-rfb1-ubiDaniel Golle2021-03-011-3/+3
| | | | | | | This profile is meant to be used on MT7622 rfb1 AP, indicate that in the name to make things less confusing. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rework support for BananaPi BPi-R64Daniel Golle2021-02-282-39/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **What's new** * Bring support for the Bananapi BPi-R64 to the level desirable for a nice hackable routerboard. * Use ARM Trusted Firmware A from source. (goodbye binary preloader) * Use Das U-Boot from source. (see previous commit) * Assemble SD-card image using OpenWrt image-commands. (no gen_sd_cruz_foo.sh added, this is not Raspbian) * Updated kernel options to support root filesystem. * Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ... * Detect root device, handle sysupgrade, config restore, ... * Wire up (known) LEDs and buttons in OpenWrt-fashion. * Build one set of images from SD-card and eMMC. * Hopefully provide a good example of how things can be done right from scratch. **Installation and images** * Have an empty SD-card at hand * Write stuff to the card, as root (card device is /dev/mmcblkX) - write header, gpt, bl2, atf, u-boot and recovery kernel: `cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX` - rescan partitions: `blockdev --rereadpt /dev/mmcblkX` - write main system to production partition: `cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5` * Installation to eMMC works using SD-card bootloader via TFTP When running OpenWrt of SD-card, issue this to trigger installation to eMMC: `fw_setenv bootcmd run emmc_init` Be prepared to serve the content of bin/targets/mediatek/mt7622 on TFTP server address 192.168.1.254. **What's missing** * The red LED is always on, probably a hardware bug. * AHCI (probably needs DTS changes) * Ship SD-card image ready with every needed for eMMC install. * The eMMC has a second, currently unused boot partition. This would be ideal to store the WiFi EEPROM and Ethernet MAC address(es). @sinovoip ideas? Thanks to Thomas Hühn @thuehn for providing the hardware! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add alternative UBI NAND layout for Linksys E8450Daniel Golle2021-02-281-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vendor flash layout of the Linksys E8450 is problematic as it uses the SPI-NAND chip without any wear-leveling while at the same time wasting a lot of space for padding. Use an all-UBI layout instead, storing the kernel+dtb+squashfs in uImage.FIT standard format in UBI volume 'fit', the read-write overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot environments 'ubootenv' and 'ubootenv2', and a 'recovery' kernel+dtb+initramfs uImage.FIT for dual-boot. ** WARNING ** THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED! Step 0 * Configure your PC to have the static IPv4 address 192.168.1.254/24 * Provide bin/targets/mediatek/mt7622 via TFTP Now continue EITHER with step 1A or 1B, depending on your preference (and on having serial console wired up or not). Step 1A (Using the vendor web interface (or non-UBI OpenWrt install)) In order to update to the new bootloader and UBI-based firmware, use the web browser of your choice to open the routers web-interface accessible on http://192.168.1.1 * Navigate to 'Configuration' -> 'Administration' -> 'Firmware Upgrade' * Upload the file openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and proceed with the upgrade. * Once OpenWrt comes up, use SCP to upload the new bootloader files to /tmp on the router: *-mt7622-linksys_e8450-ubi-preloader.bin *-mt7622-linksys_e8450-ubi-bl31-uboot.fip * Connect via SSH as you will now need to replace the bootloader in the Flash. ssh root@192.168.1.1 (the usual warnings) * First of all, backup all the flash now: for mtd in /dev/mtdblock*; do dd if=$mtd of=/tmp/$(basename $mtd); done * Then use SCP to copy /tmp/mtdblock* from the router and keep them safe. You will need them should you ever want to return to the factory firmware! * Now flow the uploaded files: mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0 mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1 If and only if both writes look like the completed successfully reboot the router. Now continue with step 2. Step 1B (Using the vendor bootloader serial console) * Use the serial to backup all /dev/mtd* devices before using the stock firmware (you got root shell when connected to serial). * Then reboot and select 'U-Boot Console' in the boot menu. * Copy the following lines, one by one: tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip nand erase 0x0 0x180000 nand write 0x40080000 0x0 0x180000 reset Now continue with step 2 Step 2 Once the new bootchain comes up, the loader will initialize UBI and the ubootenv volumes. It will then of course fail to find any bootable volume and hence resort to load kernel via TFTP from server 192.168.1.254 while giving itself the address 192.168.1.1 The requested file is called openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and your TFTP server should provide exactly that :) It will be written to UBI as recovery image and booted. You can then continue and flash the production OS image, either by using sysupgrade in the booted initramfs recovery OS, or by using the bootloader menu and TFTP. That's it. Go ahead and mess around with a bootchain built almost completely from source (only DRAM calibration blobs are fitted in bl2, and the irreplacable on-chip ROM loader remains, of course). And enjoy U-Boot built with many great features out-of-the-box. You can access the bootloader environment from within OpenWrt using the 'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got the new bootchain installed the device should be fairly unbrickable (holding reset button before and during power-on resets things and allows reflashing recovery image via TFTP) Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast infra for test-builds, allowing for `make clean ; make -j$(nproc)` in less than two minutes :) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-14 04:08:13 +0000