aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: drop linux 4.9 supportStefan Lippers-Hollmann2018-05-221-389/+0
| | | | Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: remove rpm pinctrl from board dtsPavel Kubelun2018-05-221-5/+0
| | | | | | | | | These pins seem to be used by hw exclusively, so claiming it in kernel causes an error in syslog in k4.14+. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com> [slh: rebase for kernel v4.14 as well] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500Stefan Lippers-Hollmann2018-05-221-3/+3
| | | | | | | | | | | | | | | | | | | Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the 2 MB reserved for the kernel partition by the OEM firmware anymore. This patch increases the kernel partition from 2 MB to 4 MB, at the expense of the rootfs, for all supported kernels. WARNING: This breaks sysupgrade! Flashing a firmware containing this changed partitioning from an older image with 2 MB reserved for the kernel partion requires the tftp recovery procedure, thereby losing all settings. This change follows the functional example of the Netgear r7800, but has not been runtime tested on a Netgear Nighthawk X4 R7500 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Jonas Gorski <jonas.gorski@gmail.com>
* ipq806x: force 2nd pci slot into gen1 modePavel Kubelun2018-01-171-0/+1
| | | | | | | | | | | | | | According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode. EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode. In previous commit we've added the support for this option, so enable it in DT for affected devices. QSDK ref: https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506 While at it move the phy transmit termination offset value into dtsi file as it's platform specific. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq8064: fix dwc3-of-simple module unloading for Netgear R7500Thomas Reifferscheid2017-04-241-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without patch unloading the dwc3-of-simple module went stuck after successfully removing hcd.1 during the hcd.0 removal: root@LEDE:/# rmmod dwc3-of-simple [ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.391931] usb usb4: USB disconnect, device number 1 [ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 21.406685] usb usb3: USB disconnect, device number 1 [ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 21.422521] usb usb2: USB disconnect, device number 1 followed by nothing. Sometimes a stall CPU was detected, or a kernel panic, or a reboot occurred after a couple of minutes. At the same time unloading the dwc3 module followed by dwc3-of-simple module was working repeatedly. root@LEDE:/# rmmod dwc3 [ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.827412] usb usb4: USB disconnect, device number 1 [ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 53.842314] usb usb3: USB disconnect, device number 1 [ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.857882] usb usb2: USB disconnect, device number 1 [ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 53.873696] usb usb1: USB disconnect, device number 1 [ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# rmmod dwc3-of-simple root@LEDE:/# For the non-working case, the code was stuck in a readl() in http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91 because http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126 was disabling the wrong clocks when removing hcd.1 (it was disabling the clock of hcd.0). That's why the readl() went stuck when removing hcd.0 The patch however addresses the clock assignment from the Netgear R7500 dts file and backs off the previous attempt. Now unloading and repeated module loading is working just fine. root@LEDE:/# rmmod dwc3-of-simple [ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.089765] usb usb4: USB disconnect, device number 1 [ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 24.104522] usb usb3: USB disconnect, device number 1 [ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.120396] usb usb2: USB disconnect, device number 1 [ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 24.135948] usb usb1: USB disconnect, device number 1 [ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered root@LEDE:/# Fixes: dwc3-of-simple module unloading for Netgear R7500 Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* ipq8064: enable 2nd USB port on R7500Thomas Reifferscheid2017-03-271-0/+6
| | | | | | | | | Makes use of the syscon tcsr and enables both USB ports. Cleans up qcom-ipq8064.dtsi from previous attempts. Fixes FS#497 Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
* ipq806x: fix NAND support for linux 4.9Felix Fietkau2017-03-131-56/+64
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: clean up dts patchFelix Fietkau2017-03-081-0/+373
Move dts files to files/, remove useless patch chunks Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-26 01:27:17 +0000