aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2023-01-011-0/+18
| | | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com> (cherry picked from commit 6fc334cbdc2b1716786768c545b761b338962b43)
* ipq40xx: fix ZTE MF289F port mappingLech Perczak2022-11-051-1/+1
| | | | | | | | | | | With initial support, the mapping of LAN1/WAN and LAN2 ports was swapped. Fix it to match labels on the device, keeping the "WAN" personality of the first port - in line with current state of DSA setup in master for this device. Tested-by: Marcin Gajda <mgajda@o2.pl> Tested-by: Christian Heuff <christian@heuff.at> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: Add ZTE MF289FGiammarco Marzano2022-11-053-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 0de6a3339f1aadc1de2c9371435e3de239a00645) [Backported to 22.03: added DTS to the makefile patch, fixed ipq-wifi inclusion for MF286D] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: add WAN LED mapping for GL-AP1300David Bauer2022-09-111-0/+3
| | | | | Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4d014a7bd6d8fbfe7dc4cebd6c55d85601231fa4)
* ipq40xx: fix RUTX10 Wi-Fi woesKasparas Elzbutas2022-08-051-0/+8
| | | | | | | | | | | | | This partially reverts: commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") U-Boot on these devices mangles the device tree, so nvmem-cell type calibration doesn't work. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Signed-off-by: Kasparas Elzbutas <elzkas@gmail.com> (added reference to commit, rewrote commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: mikrotik: provide BDF-s on demandRobert Marko2022-07-011-0/+23
| | | | | | | | | | | | | Since we now can pass the API 1 BDF-s aka board.bin to the ath10k driver per radio lets use that to provide the BDF-s for MikroTik devices. This also resolves the performance issues that happen as MikroTik changes the boards and ships them under the same revision but they actually ship with and require a different BDF. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 4d4462cc2ace4b044e99e9b22a24cb4d89c7db95) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq40xx: revert Cell-C RTL30VW to legacy caldata extractionPawel Dembicki2022-05-151-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data"). After switching to nvmem RTL30VW, wifi was broken: [ 19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin [ 19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 [ 19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12 [ 19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12) [ 20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin [ 20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 [ 20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12 [ 20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12) Bootloader mangles in NAND partitions and removes precal@X nodes in working system: root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label) 0:ART root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/ label name reg Revert to legacy method fixed the problem. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cherry picked from commit af425e42212d476dd95ec31f18d85b19004c9268)
* ipq40xx: Lyra: update RGB LED-Controller node for 5.10+Christian Lamparter2022-05-151-0/+3
| | | | | | | | | | | | | | | | | | | | | | | Add the reg and color property to each channel node. This update is to accommodate the multicolor framework. Refer to: <https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com> <https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com> Note: There is only a single extremely bright RGB-LED. The RGB-color channels (i.e.: blue-0, blue-1 and blue-2) are running in parallel to increase the current delivery beyond what a single PWM-output on the LED controller could do. BugLink: https://github.com/openwrt/openwrt/issues/9851 Reported-By: Thomas Bøge <thomas@boegenielsen.dk> Tested-By: Thomas Bøge <thomas@boegenielsen.dk> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 834c9b3f055e5ea719f6adfb3fa979e32f2adbd0)
* ipq40xx: WAC510: device-tree overhaulingChristian Lamparter2022-03-271-0/+3
| | | | | | | | | | removes usb-port remains as neither the WAC510 nor the WAC505 come with a USB port. Update the LED properties to phase out labels and introduce generic node-names as well as adding the color, function and function-enumerator properties. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 026fda10a5c45d56fd856628b6e9e69b95fd5e58)
* ipq40xx: add support for Telco X1 ProNicholas Smith2022-03-191-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Telco X1 Pro is a Cat12 LTE-A Pro modem router. Vendor firmware is based on a recent version of OpenWrt. Flashing is possible via CLI using sysupgrade -F -n The serial headers allow bootloader and console access Serial setting: 115200 8N1 Brief Specifications: IPQ4019 SoC 32MB flash 512MB RAM 4x gigabit LAN 1x gigabit WAN Dual-band Wave-2 wifi 2x SMA LTE antenna connectors 2x RP-SMA wifi antennas 1x USB 2.0 port 1x Reset button Serial headers installed 1x Nano SIM tray 1x Quectel EM-12G LTE-A Pro modem 1x M.2 slot attached to USB 3.0 1x internal micro SD card slot Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
* ipq40xx: mikrotik: fix LED scriptRobert Marko2022-02-201-0/+1
| | | | | | | | Fix the missing ;; after the cAP ac case in /e/b/01_leds. Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support") Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
* ipq40xx: add Linksys MR8300 WAN portJulien Cassette2022-02-051-2/+6
| | | | | | | | | | This makes the WAN interface and port appear in LuCi -> Network -> Switch on Linksys MR8300. This allows to configure a VLAN on WAN. Fixes: FS#4227 Signed-off-by: Julien Cassette <julien.cassette@gmail.com>
* ipq40xx: add support for ZTE MF286DPawel Dembicki2022-02-053-1/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF286D is a LTE router with four gigabit ethernet ports and integrated QMI mPCIE modem. Hardware specification: - CPU: IPQ4019 - RAM: 256MB - Flash: NAND 128MB + NOR 2MB - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2 - LTE: mPCIe cat 12 card (Modem chipset MDM9250) - LAN: 4 Gigabit Ports - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem) - Serial console: X8 connector 115200 8n1 Known issues: - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs are driven by cpu. - Wifi LED is triggered by phy0tpt only - No VoIP support - LAN1/WAN port is configured as WAN - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN and WLAN0/1 Opening the case: 1. Take of battery lid (no battery support for this model, battery cage is dummy). 2. Unscrew screw placed behind battery lid. 3. Take off back cover. It attached with multiple plastic clamps. 4. Unscrew four more screws hidden behind back case. 5. Remove front panel from blue chassis. There are more plastic clamps. 6. Unscrew two boards, which secures the PCB in the chassis. 7. Extract board from blue chassis. Console connection (X8 connector): 1. Parameters: 115200 8N1 2. Pin description: (from closest pin to X8 descriptor to farthest) - VCC (3.3V) - TX - RX - GND Install Instructions: Serial + initramfs: 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3 2. Connect serial console (115200,8n1) to X8 connector. 3. Connect TFTP server to RJ-45 port. 4. Stop in u-Boot and run u-Boot commands: setenv serverip 192.168.1.3 setenv ipaddr 192.168.1.72 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock. 6. Login via ssh or serial and remove stock partitions: ubiattach -m 9 ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. Install image via "sysupgrade -n". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cosmetic changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add MikroTik cAP ac supportAlar Aun2022-02-015-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD (cAP ac), a indoor dual band, dual-radio 802.11ac wireless AP, two 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/cap_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port, PoE in and passive PoE out Unsupported: - PoE out Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Alar Aun <alar.aun@gmail.com>
* ipq40xx: rename RT-AC42U WLAN/LAN LEDsSungbo Eo2022-01-171-4/+4
| | | | | | | | | | Assign LED numbers properly by adding function-enumerator property in DTS. While at it, remove default trigger of LAN LEDs as it will be handled in 01_leds anyway. Fixes: 51b9aef553a8 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: utilize nvmem-cells for macs & (pre-)calibration dataChristian Lamparter2022-01-151-95/+5
| | | | | | | | | | | | | | | moves extraction entries out of 11-ath10k-caldata and into the individual board's device-tree. Some notes: - mmc could work as well (not tested) - devices that pass the partitions via mtdparts bootargs are kept as is - gl-b2200 has a weird pcie wifi device (vendor claims 9886 wave 2. But firmware-extraction was for a wave 1 device?!) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-156-11/+20
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUPChristian Lamparter2021-12-042-6/+0
| | | | | | | | | | introduce nvmem pre-cal + mac-address cells for both Wifis and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of the few devices in which the correct mac adress is already at the right place for Wifi, so no separate nvmem cell is needed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10Christian Lamparter2021-12-041-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | with current images, the device is no longer booting. It gets stuck in the bootloader with "Config not available" and drops to the uboot shell. |flash_type: 0 |Hit any key to stop autoboot: 0 |SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB |Config not availabale |(IPQ40xx) # This is because the default bootcmd "bootipq" will only read the first four MiB of the kernel image. With 5.10 the gzip'd kernel is slightly larger. So the part of the FIT image which had the configuration is cut off. Hence it can't find it. To update the bootcmd, you have to attach the serial console again and enter the following commands into the boot prompt: # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm" # saveenv # run bootcmd This will allow booting kernels with up to six MiB. This also allows us to drop the DEVICE_DTS_CONFIG hack we had to use. Note: uboot doesn't support LZMA. It fails with: "Unimplemented compression type 3" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: sysupgrade: drop disabled UBI to UBI logicBjørn Mork2021-12-031-22/+2
| | | | | | | | | | | | | | | | The commented out code is not required, as the comment indicates. The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq40xx: add support for GL.iNet GL-B2200TruongSinh Tran-Nguyen2021-12-023-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dishAlexander Couzens2021-12-023-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | LHGG-60ad is IPQ4019 + wil6210 based. Specification: - Qualcomm IPQ4019 (717 MHz) - 256 MB of RAM (DDR3L) - 16 MB (SPI NOR) of flash - 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035. - WLAN: wil6210 802.11ad PCI card - No USB or SD card ports - UART disabled - 8x LEDs Biggest news is the wil6210 PCI card. Integration for its configuration and detection has already been taken care of when adding support for TP-Link Talon AD7200. However, signal quality is much lower than with stock firmware, so probably additional board-specific data has to be provided to the driver and is still missing at the moment. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [Fix Ethernet Interface] Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: Add support for Teltonika RUTX10Felix Matouschek2021-11-283-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
* ipq40xx: add support for MikroTik hAP ac3Robert Marko2021-11-285-3/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD (hAP ac³), a indoor dual band, dual-radio 802.11ac wireless AP with external omnidirectional antennae, USB port, five 10/100/1000 Mbps Ethernet ports and PoE passthrough. See https://mikrotik.com/product/hap_ac3 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR + 128 MB NAND - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in, PoE passtrough on port 5 - 1x USB Type A port Installation: 1. Boot the initramfs image via TFTP 2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1" 3. Use ubiformat to remove MikroTik specific UBI volumes * Detach the UBI partition by running: "ubidetach -d 0" * Format the partition by running: "ubiformat /dev/mtdN -y" Replace mtdN with the correct mtd index from step 2. 3. Flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> Tested-by: Mark Birss <markbirss@gmail.com> Tested-by: Michael Büchler <michael.buechler@posteo.net> Tested-by: Alex Tomkins <tomkins@darkzone.net>
* ipq40xx: utilize nvmem on Netgear EX61X0 v2 SeriesChristian Lamparter2021-11-281-10/+0
| | | | | | | | the Netgear EX6100v2 and EX6150v2 can utilize the nvmem for the pre-calibration and mac-address for both WIFI devices. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)Richard Yu2021-11-143-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50Davide Fioravanti2021-11-014-0/+111
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost identical AC3000 routers. The SRR60 has one port labeled as wan while the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a different external shape but they have an USB 2.0 port on the back. This patch has been tested only on SRS60 and RBR50, but should work on SRR60 and RBS50. Hardware -------- SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads) RAM: 512MB DDR3 FLASH: 4GB EMMC ETH: - 3x 10/100/1000 Mbps Ethernet - 1x 10/100/1000 Mbps Ethernet (WAN) WIFI: - 2.4GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x QCA9984 (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x Sync button - 1x ON/OFF button LEDS: - 8 leds controlled by TLC59208F (they can be switched on/off independendently but the color can by changed by GPIOs) - 1x Red led (Power) - 1x Green led (Power) UART: - 115200-8-N-1 Everything works correctly. Installation ------------ These routers have a dual partition system. However this firmware works only on boot partition 1 and the OEM web interface will always flash on the partition currently not booted. The following steps will use the SRS60 firmware, but you have to chose the right firmware for your router. There are 2 ways to install Openwrt the first time: 1) Using NMRPflash 1. Download nmrpflash (https://github.com/jclehner/nmrpflash) 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img file in the same folder of the nmrpflash executable 3. Connect your pc to the router using the port near the power button. 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img". Replace XXX with your network interface (can be identified by running "nmrpflash -L") 5. Power on the router and wait for the flash to complete. After about a minute the router should boot directly to Openwrt. If nothing happens try to reboot the router. If you have problems flashing try to set "10.164.183.253" as your computer IP address 2) Without NMRPflash The OEM web interface will always flash on the partition currently not booted, so to flash OpenWrt for the first time you have to switch to boot partition 2 and then flash the factory image directly from the OEM web interface. To switch on partition 2 you have to enable telnet first: 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet". 2. Connect through telent ("telnet 192.168.1.250") and login using admin/password. To read the current boot_part: artmtd -r boot_part To write the new boot_part: artmtd -w boot_part 02 Then reboot the router and then check again the current booted partition Now that you are on boot partition 2 you can flash the factory Openwrt image directly from the OEM web interface. Restore OEM Firmware -------------------- 1. Download the stock firmware from official netgear support. 2. Follow the nmrpflash procedure like above, using the official Netgear firmware (for example SRS60-V2.2.1.210.img) nmrpflash -i XXX -f SRS60-V2.2.1.210.img Notes ----- 1) You can check and edit the boot partition in the Uboot shell using the UART connection. "boot_partition_show" shows the current boot partition "boot_partition_set 1" sets the current boot partition to 1 2) Router mac addresses: LAN XX:XX:XX:XX:XX:69 WAN XX:XX:XX:XX:XX:6a WIFI 2G XX:XX:XX:XX:XX:69 WIFI 5G XX:XX:XX:XX:XX:6b WIFI 5G (2nd) XX:XX:XX:XX:XX:6c LABEL XX:XX:XX:XX:XX:69 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> [added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved sysupgrade mmc.sh to here and renamed it, various dtsi changes] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add missing case closing symbolAdrian Schmutzler2021-06-281-0/+1
| | | | | | | Though not strictly necessary, add the closing symbol to make the job easier for future developers editing this file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: specify FritzBox 7530 LAN port label numbersRafał Miłecki2021-06-241-1/+1
| | | | | | | | | This helps managing LAN ports. Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121 Fixes: 95b0c07a618f ("ipq40xx: add support for FritzBox 7530") Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-052-16/+16
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-054-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for MikroTik SXTsq 5 acRoger Pueyo Centelles2021-04-294-2/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-053-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-063-3/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-253-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-223-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-224-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-224-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Change name for openmesh.sh to vendor-free nameSven Eckelmann2020-12-222-5/+5
| | | | | | | | | Other vendors are using functionality similar to the ones OpenMesh used to implement two areas on the flash to store the default image and a fallback image. So just change the name to dualboot_datachk.sh to avoid duplicated code just to have the same script for different vendors. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: improve support for Edgecore ECW5211Sungbo Eo2020-10-071-6/+5
| | | | | | | | | | | | | | | | | | | This adds several stylistic and functional improvements of the recently added Edgecore ECW5211, especially: * Drop the local BDFs as those are already in the upstream under different names * Add SPDX tag to DTS * Add label MAC address * Move LED trigger to DTS * Remove unnecessary status="okay" * Disable unused SS USB phy as the USB port only supports USB 2.0 * Make uboot-env partition writable * Remove qcom,poll_required_dynamic property as the driver does not use it * Tidy up the device recipe Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: remove model name from LED labelsAdrian Schmutzler2020-10-072-36/+51
| | | | | | | | | | | Like in the previous patches for ath79 and ramips, this will remove the "devicename" from LED labels in ipq40xx. The devicename is removed in DTS files and 01_leds, and a migration script is added. While at it, also harmonize capitalization of wlan2G/wlan5G vs. wlan2g/wlan5g. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: Add support for Linksys MR8300 (Dallas)Hans Geiblinger2020-09-257-8/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Luma Home WRTQ-329ACNTomasz Maciej Nowak2020-09-253-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band wireless access point. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 2 MB SPI NOR 128 MB SPI NAND WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 2x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU Buttons: 1x GPIO controlled EEPROM: 16 Kbit, compatible with AT24C16 UART: row of 4 holes marked on PCB as J19, starting count from the side of J19 marking on PCB 1. GND, 2. RX, 3. TX, 4. 3.3V baud: 115200, parity: none, flow control: none The device supports OTA or USB flash drive updates, unfotunately they are signed. Until the signing key is known, the UART access is mandatory for installation. The difficult part is disassembling the casing, there are a lot of latches holding it together. Teardown Prepare three thin, but sturdy, prying tools. Place the device with back of it facing upwards. Start with the wall having a small notch. Insert first tool, until You'll feel resistance and keep it there. Repeat the procedure for neighbouring walls. With applying a pressure, one edge of the back cover should pop up. Now carefully slide one of the tools to free the rest of the latches. There's no need to solder pins to the UART holes, You can use hook clips, but wiring them outside the casing, will ease debuging and recovery if problems occur. Installation 1. Prepare TFTP server with OpenWrt initramfs image. 2. Connect to UART port (don't connect the voltage pin). 3. Connect to LAN port. 4. Power on the device, carefully observe the console output and when asked quickly enter the failsafe mode. 5. Invoke 'mount_root'. 6. After the overlayfs is mounted run: fw_setenv bootdelay 3 This will allow to access U-Boot shell. 7. Reboot the device and when prompted to stop autoboot, hit any key. 8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x84000000 <openwrt_initramfs_image_name> bootm 0x84000000 and wait till OpenWrt boots. 9. In OpenWrt command line run following commands: fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000" fw_setenv bootcmd "run openwrt" 10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: ubirmvol /dev/ubi0 -N ubi_rootfs sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name> 11. After flashing, the access point will reboot to OpenWrt, then it's ready for configuration. Reverting to OEM firmware 1. Execute installation guide steps: 1, 2, 3, 7, 8. 2. In OpenWrt command line run following commands: ubirmvol /dev/ubi0 -N rootfs_data ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N kernel ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs ubimkvol /dev/ubi0 -S 34 -N kernel1 ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1 ubimkvol /dev/ubi0 -S 264 -N rootfs_data fw_setenv bootcmd bootipq 3. Reboot. Known issues The LEDs ring doesn't have any dedicated driver or application to control it, the only available option atm is to manipulate it with 'i2cset' command. The default action after applying power to device is spinning blue light. This light will stay active at all time. To disable it install 'i2c-tools' with opkg and run: i2cset -y 2 0x48 3 1 0 0 i The light will stay off until next cold boot. Additional information After completing 5. step from installation guide, one can disable asking for root password on OEM firmware by running: sed -e 's/root:x:/root::/' -i /etc/passwd This is useful for investigating the OEM firmware. One can look at the communication between the stock firmware and the vendor's cloud servers or as a way of making a backup of both flash chips. The root password seems to be constant across all sold devices. This is output of 'led_ctl' from OEM firmware to illustrate possibilities of LEDs ring: Usage: led_ctl [status | upgrade | force_upgrade | version] led_ctl solid COLOR <brightness> led_ctl single COLOR INDEX <brightness 0 - 15> led_ctl spinning COLOR <period 1 - 16 (lower = faster)> led_ctl fill COLOR <period 1 - 16 (lower = faster)> ( default is 5 ) led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128> (default is 34) ( default is 34 ) led_ctl pulsing COLOR COLOR: red, green, blue, yellow, purple, cyan, white Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit, changed ubi volumes for easier integration, slightly reworded commit message, changed ubi volume layout to use standard names all around] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: enable FRITZRepeater 3000 ports on switchDavid Bauer2020-09-171-1/+4
| | | | | | | | | | | | The ethernet ports on the AVM FRITZRepeater 3000 are not separated between LAN and WAN in the stock firmware. OpenWrt currently abstracts port 4 as eth0 and port 5 as eth1, bridging them in the kernel. This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx to bridge them on the switch, avoiding traffic on both ports to pass thru the CPU. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: remove empty default casesAdrian Schmutzler2020-09-172-4/+0
| | | | | | There is no apparent reason to have an empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add Edgecore OAP-100 supportJohn Crispin2020-09-174-0/+8
| | | | | | | | | | | | | | | | flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: add Edgecore ECW5211 supportRobert Marko2020-09-174-0/+5
| | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add support for Buffalo WTR-M2133HPYanase Yuki2020-07-083-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019. Specification ------------- - SoC: Qualcomm IPQ4019 - RAM: 512MiB - Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC) - Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch) - Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch) - Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN) - LED: 4x white LED, 4x orange LED, 1x blue LED - USB: 1x USB 3.0 port - Input: 2x tactile switch, 2x slide switch (2x SP3T) - Serial console: 115200bps, pinheader JP5 on PCB - Power: DC 12V 2A Flash instruction ----------------- 1. Set up a TFTP server (IP address: 192.168.11.10) 2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage" and put it into the TFTP server directory. 3. Connect the TFTP server and WTR-M2133HP. 4. Hold down the AOSS button, then power on the router. 5. After booting OpenWrt initramfs image, connect to the router by SSH. 6. Transfer "squashfs-nand-factory.ubi" to the router. 7. Execute the following commands. # ubidetach -p /dev/mtd15 # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi # fw_setenv bootcmd bootipq 8. Perform reboot. Recover to stock firmware ------------------------- 1. Execute the following command. # fw_setenv bootcmd bootbf 2. Reboot and wait several minutes. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add support for GL.iNet GL-S1300Dongming Han2020-07-082-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-162-4/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-19 09:55:46 +0000