openwrt/upstream - upstream openwrt

	Commit message (Collapse)	Author	Age	Files	Lines
*	brcm47xx: remove kernel 3.10	Hauke Mehrtens	2014-12-07	1	-13/+0
\| \| \| \| \| \|	Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 43535
*	brcm47xx: fix reboot problem on BCM4705/BCM4785	Hauke Mehrtens	2014-08-08	1	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	This adds some code based on code from the Broadcom GPL tar to fix the reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10 times and have never seen a problem. This reverts the changes in the previous commit and adds the real fix as suggested by Rafał. Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into async mode. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 42083
*	brcm47xx: add new led and button support	Hauke Mehrtens	2014-01-12	1	-1/+1
\| \| \| \| \| \|	Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39252
*	brcm47xx: b44: This updates the phylib patches to the version send upstream	Hauke Mehrtens	2013-12-26	1	-1/+1
\| \| \| \| \| \| \| \|	This uses a fixed phy instead of a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39166
*	brcm47xx: deactivate mips wait instruction only for BCM4706	Hauke Mehrtens	2013-12-01	1	-1/+1
\| \| \| \| \| \| \| \| \|	The wait instruction is only broken on the BCM4706 and not on the other similar SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38979
*	brcm47xx: update early printk patches	Hauke Mehrtens	2013-10-06	1	-1/+1
\| \| \| \| \| \| \| \| \| \|	Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38309
*	brcm47xx: update board detection patches	Hauke Mehrtens	2013-10-06	1	-1/+1
\| \| \| \| \| \| \| \| \| \| \|	Add patches like they are currently in the mainline mips tree and add some more pending patches for board detection. * Now the board name is shown under machine in /proc/cpuinfo. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38308
*	brcm47xx: Add support for Huawei E970	Hauke Mehrtens	2013-09-16	1	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	This patch adds support for Huawei E970 wireless gateway devices. It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV. E960/B970 should work too, from what I know it's basically the same hardware. The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem. It uses a hardware watchdog which needs GPIO-7 to be toggled at least every 1-2 seconds. This patch uses gpio_wdt module (see my previous patch today) to take care of this. Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset button, image to be used for upgrade from OEM firmware's web interface Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970> Issue: * lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog reset during kernel decompress. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> SVN-Revision: 38011
*	brcm47xx: add initial support for kernel 3.10	Hauke Mehrtens	2013-07-14	1	-0/+13
	SVN-Revision: 37287