aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/files
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-244-0/+143
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-114-0/+239
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-115-1/+298
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx/ag71xx_ethtool: don't return uninitialized return value on successAlexander Couzens2017-06-111-1/+1
| | | | | | | | ag71xx_ethtool_set_ringparam() will return an uninitialized value on success. Found-by: Coverity Scan #1330877 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/ag71xx_mdio_probe: fix a memory leak when probe failsAlexander Couzens2017-06-111-1/+1
| | | | | Found-by: Coverity Scan #1330233 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/ag71xx_ar7240_get_port_link: fix off-by-one check on argument `port`Alexander Couzens2017-06-111-2/+2
| | | | | Found-by: Coverity Scan #1329901 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: Fix UBIFS work on Mikrotik RB95x devicesSergey Sergeev2017-05-311-0/+2
| | | | | | | | If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options ubifs can't use it mtd devices and the kernel crashes with error: __nand_correct_data: uncorrectable ECC error Signed-off-by: Sergey Sergeev <adron@yapic.net>
* ar71xx: fix Wallys DR344 GPIO-connected LEDs and buttonPiotr Dymacz2017-05-301-10/+26
| | | | | | | | | | | | | | | | | | | | This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board and sets color of all LEDs to green as the mass production boards have only green one. Actually, DR344 has 6 GPIO-connected LEDs and one button: - GPIO11: status - GPIO12: sig1 - GPIO13: sig2 - GPIO14: sig3 - GPIO15: sig4 - GPIO16: reset button - GPIO17: lan WAN LED is connected directly with AR8035 PHY. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix GE interface support in Wallys DR344Piotr Dymacz2017-05-301-30/+8
| | | | | | | | GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with AR8035, not with AR8327. Without this fix, GE interface doesn't work at all or shows high packet loss ratio. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for EnGenius ENS202EXTMarty Plummer2017-05-304-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
* ar71xx: fix LED defines for TP-Link TL-WR740N v6Andrey Polischuk2017-05-303-1/+88
| | | | | | Signed-off-by: Andrey Polischuk <androld.b@gmail.com> [changed commit subject, dropped redundant kernel config symbol] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-274-0/+163
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* Make GBit switch work on RB2011René Mayrhofer2017-05-251-1/+2
| | | | | | | | | | | | | | | | | | | | | This change is required to make the GBit switch work on my Mikrotik Routerboard RB2011UiAS-RM, and I assume that the other RB2011 variants are exactly the same in terms of the switch. I have tested the board without and with the patch and confirm that the GBit ports are not supported at all (i.e. no communication works) with the current version in trunk and that everything works with the patch applied. The test box has been running for a few days with the patch applied, and does not show any performance problems in a test setting. I have not used it with LEDE in production so far, but with a previous turnk version of OpenWRT for many years - with the same patch applied. I therefore have good indication that it is stable. For the record, the switch chip on my test box is identified as switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0 The value 0x6f000000 has been taken from the table at https://wiki.openwrt.org/toh/mikrotik/rb2011uias with the previous discussion thread still online at https://lists.openwrt.org/pipermail/openwrt-devel/2014-December/029949.html. One definite improvement from the older OpenWRT trunk version I have been running in production and current LEDE trunk is that the SFP interface can be kept in the default configuration without excessive kernel messages about it constantly going up and down. I have not yet tested an actual SFP module, though. Performance seems to be reasonable. Routing between two GBit ports on that switch separated by different VLANs with the default firewall ruleset (and one additional rule two allow traffic between the VLANs), but without NAT, iperf3 results are: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 508 MBytes 426 Mbits/sec 102 sender [ 4] 0.00-10.00 sec 506 MBytes 425 Mbits/sec receiver With a connection going through NAT (also 2 ports on the same GBit switch, same ruleset, but NAT active), routing performance drops to around 250 MBit/s. (Note that RouterOS achieves beyond 900 MBit/s on the same hardware with the default rule set and the FastTrack rule active even for NAT, see https://wiki.mikrotik.com/index.php?title=Manual:IP/Fasttrack and http://www.mikrotik.com/download/share/FastTrack.pdf). Summarizing, I strongly recommend to apply this patch in trunk, so that the GBit switch chip rev. 4 can be supported upstream in the next LEDE release (hopefully soon). Signed-off-by: René Mayrhofer <rene@mayrhofer.eu.org>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-185-479/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-185-0/+479
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: add support for Aerohive AP-121Chris Blake2017-05-154-0/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Aerohive AP-121 access point. Specification: - SoC: Atheros AR9344-BC2A at 560MHz - WiFi 1: 2.4GHz Atheros AR9340? - SoC - WiFi 2: 5.0GHz Atheros AR9382-AL1A - Memory: 128MB from 2x Nanya NT5TU32M16DG-AC - SPI: 1MB Macronix MX25L8006E - NAND: 128MB Hynix H27U1G8F2BTR-BC - Ethernet: Atheros AR8035-A - USB: 1x 2.0 - TPM: Atmel SC3204 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, download and flash LEDE factory image over tftp: dhcp; setenv serverip tftp-server-ip; tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin; nand erase 0x800000 0x800000; nand write 0x81000000 0x800000 0x800000; reset; Signed-off-by: Chris Blake <chrisrblake93@gmail.com> [minor text changes in commit subject and description, fixed alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh, fixed code style issues in mach-hiveap-121.c, ubinized factory image] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for 8devices Rambutan development boardMantas Pucka2017-05-154-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan This commit adds basic support for Rambutan development kit Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header Flash instructions: Stock firmware is OpenWrt, so use: sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar or upgarde from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Mantas Pucka <mantas@8devices.com> [split support in uboot-envtools package into a separate commit, fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for UniFi-AC-MeshLudwig Thomeczek2017-05-153-6/+6
| | | | | | | | | | | | | | | | | | | This adds the build option for the new UniFi AC Mesh. It is a direct hardware copy from the AC Lite. - SoC: QCA9563-AL3A (775Mhz) - RAM: 128MiB - Flash: 16MiB - dual firmware partitions! - LAN: 1 1000M - POE - Wireless: 2.4G: QCA9563 5G: UniFi Chip, QCA988X compatible Thanks to Frank Dietz for testing. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [wrapped too long lines in mach-ubnt-unifiac.c] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix ath9k default LED changes falloutMathias Kresin2017-04-133-13/+15
| | | | | | | | | | | | | | | | Since 192f0a3db859 ("ath9k: unset the default LED pin if used by platform leds") the default ath9k wireless LED is not set as soon as any pin of the ath ath9k gpio controller is used. All touched boards have leds defined which are using the gpio pins exposed by the ath9k driver but rely on a default set wireless led trigger. Add the wireless leds were missing and setup the wireless phy trigger in userspace. Signed-off-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add correct named default wireless led by using platform ledsMathias Kresin2017-04-084-40/+25
| | | | | | | | | | | | | Instead of renaming the default wireless led attached to the wireless chip, add a new led using the platform leds with the phy0tpt trigger set in userspace. When switching ar71xx to device tree, the same can be done by using the build in GPIO controller and without adding new bindings. Drop the now unused platform code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-304-0/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: wpj531: fix GPIOs for LEDLeon M. George2017-03-271-4/+4
| | | | | | /sys/devices/platform/leds-gpio/leds/ was not initialised with working LEDs. Signed-off-by: Leon M. George <leon@georgemail.eu>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-234-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-234-1/+76
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for MikroTik hAP acRyan Mounce2017-03-233-0/+160
| | | | | | | | | | | This patch adds initial support for the MikroTik RouterBOARD hAP ac (RB962UiGS-5HacT2HnT). All functions are supported except: -SFP cage (eth1) is not working -WLAN LEDs are not working Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for MikroTik hAP ac liteRyan Mounce2017-03-233-6/+25
| | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP ac lite (RB952Ui-5ac2nD). The hAP ac lite is nearly identical to the hAP, with an added QCA9887 5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: mikrotik: prepend "RouterBOARD" to machine name for NOR devicesThibaut VARENE2017-03-151-3/+15
| | | | | | | | | | | | When the device name doesn't already contain "RouterBOARD", this patch adds this string to the machine name. Most NOR devices already have "RouterBOARD" in their hardware-stored device name, but not all of them. This patch also makes the code more robust against buffer overflows. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB LHG 5nDThibaut VARENE2017-03-153-31/+126
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD LHG 5 https://routerboard.com/RBLHG-5nD Specifications: - SoC: Atheros AR9344 (600MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin AR9344 5GHz, 2x2:2 - Ethernet: 1x100M Initial flash via initramfs, like all other RB devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: WNDR4300: Fix switch HW controlled LEDsDaniel Gonzalez Cabanelas2017-03-131-4/+4
| | | | | | | | | | | | The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch, has two LEDs on each port for monitoring LAN activity, but it currently only uses one. Fix the configuration to use both. The patch provides this new configuration: - green LED: 1 Gbps link, 4Hz blink frequency - amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ar71xx: fix Wallys DR344 ethernet MAC addresses offsetsPiotr Dymacz2017-03-121-2/+3
| | | | | | | Without this fix, ethernet interfaces on Wallys DR344 use random MAC addresses. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix machine name for several devicesPiotr Dymacz2017-03-123-4/+4
| | | | | | Be consistent with form and format of the vendor name. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-124-0/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* ar71xx: set status led for the gl-* boardsWojciech Jowsa2017-03-062-116/+116
| | | | Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
* ar71xx: Enable mtdsplit support for RB SPI NOR devicesThibaut VARENE2017-02-221-14/+4
| | | | | | | | | | | | | | | | | | This patch enables mtdsplit for the MikroTik subtarget. It converts mach-rbspi.c to use a single "firmware" partition. Finally, it converts the SPI NOR profile to metadata images: the original combined-image format is gone, the images are now "standard" sysupgrade images with metadata appended. Note: kernel2minor apparently pads the kernel container to erase-block boundary, but this is undocumented behaviour, so we do not rely on it and call pad-to anyway. Note: in platform.sh, the boards are tested last in platform_check_image() as this should eventually become the "*)" default case when more devices switch to metadata images. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-204-0/+107
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: fix ethernet PLL configuration for QCA956xFelix Fietkau2017-02-171-1/+1
| | | | | | | QCA956x is configured like AR934x, not like the older chips. Should fix ethernet hangs when using the WAN port without SGMII Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix lan ports on archer C59 and C60Henryk Heisig2017-02-172-6/+30
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for 8devices Lima boardKarol Dudek2017-02-174-0/+101
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lima is a module for the (IoE) internet of everything applications, based on Qualcomm/Atheros QCA4531. Specification: - 650/600/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 32 MB of FLASH - 2T2R 2.4 GHz - 2x 10/100 Mbps Ethernet - USB 2.0 Host - PCIe - UART for serial console - 14x GPIO Flash instruction: 1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin and rename it to 8dev_recovery.bin 2. Binary file copy to USB stick and plug into slot USB 3. Press S2 (reset) button 4. Press and hold the S1 button by 5 seconds 5. Wait ~40 seconds to complete recovery Tested on: - Lima development kit Signed-off-by: Karol Dudek <karoiz@sli.pl>
* ar71xx: add preliminary kernel support for several RB SPI NOR devicesThibaut VARENE2017-02-153-0/+184
| | | | | | | | | | | | | | | | | | | The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR platform. This patch adds preliminary kernel support based on init data used in Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and untested, the necessary glue in base-files has not been added, the code is provided as a starting point in case somebody with that hardware wants to help getting it supported. The cAP lite (cAPL 2nD) should also be supported once it is determined whether or not it uses the same board identifier as the mAP lite. Code has been successfully built and has no side effect (no impact on already supported devices). Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB750r2Thibaut VARENE2017-02-152-4/+10
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX lite https://routerboard.com/RB750r2 Specifications: - SoC: Qualcomm QCA9531 (850MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in) This ethernet router is based on the same platform as the hEX PoE lite (it shares the same board identifier), but has no USB and no PoE out. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB750UPr2Thibaut VARENE2017-02-153-19/+51
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hEX PoE lite https://routerboard.com/RB750UPr2 Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in, 1 PoE out) - USB: Type A This ethernet router is based on the same platform as the wireless router hAP. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB951Ui-2nDThibaut VARENE2017-02-153-1/+149
| | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD hAP https://routerboard.com/RB951Ui-2nD Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 5x100M (1 PoE in, 1 PoE out) - USB: Type A Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: provide support for RB-941-2nD via mach-rbspi.cThibaut VARENE2017-02-153-183/+40
| | | | | | | | | This patch implements support for the hAP lite in mach-rbspi.c hAP lite was supported via mach-rb941.c, so this file is removed as well as the corresponding build bits. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB mAP L-2nDThibaut VARENE2017-02-154-0/+294
| | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP lite https://routerboard.com/RBmAPL-2nD Specifications: - SoC: Qualcomm QCA9533 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9533, 2x2:2 - Ethernet: 1x100M This is another 16M SPI NOR mikrotik device. The machine file is named mach-rbspi.c because I plan to add support for several of the other spi-based RouterBOARD devices in subsequent patches: they share most of the hardware and thus the same codebase. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: Add support for D-Link EBR-2310 Rev. CAlexandru Gagniuc2017-02-142-0/+4
| | | | | | | Add support for the EBR-2310, which is almost identical to the DIR-615 rev E4, without the wifi. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-144-2/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add kernel support for the OpenMesh A40 boardSven Eckelmann2017-02-143-1/+23
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add kernel support for the OpenMesh A60 boardSven Eckelmann2017-02-144-0/+172
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add kernel support for the OpenMesh OM2Pv4/-HSv4Sven Eckelmann2017-02-143-0/+97
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: fix indentation in Kconfig.openwrtPiotr Dymacz2017-02-031-38/+40
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>