aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
...
* dropbear: init: replace backticks with $()Rui Salvaterra2020-06-301-3/+3
| | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [add commit description] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* package: add ravpower-mcu packageDavid Bauer2020-06-291-0/+34
| | | | | | | This package allows to read battery status information and control the power state of the RAVPower RP-WD009 power management IC. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for RAVPower RP-WD009David Bauer2020-06-292-0/+324
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD009 is a batter-powered pocket sized router with SD card lot and USB port. Hardware -------- CPU: MediaTek MT7628AN RAM: 64M DDR2 FLASH: 16M GigaDevices SPI-NOR WLAN: MediaTek MT7628AN 2T2R b/g/n MediaTek MT7610E 1T1R n/ac ETH: 1x FastEthernet SD: SD Card slot USB: USB 2.0 Custom PMIC on the I2C bus (address 0x0a). Installation ------------ 1. Press and hold down the reset button. 2. Power up the Device. Keep pressing the reset button for 10 more seconds until the Globe LED lights up. 3. Attach your Computer to the Ethernet port. Assign yourself the address 10.10.10.1/24. 4. Access the recovery page at 10.10.10.128 and upload the OpenWrt factory image. 5. The flashing will take around 1 minute. The device will reboot automatically into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-kirkwood: Revert "uboot-kirkwood: enable sata in nsa310 uboot"Hauke Mehrtens2020-06-271-3/+1
| | | | | | | | | | | This reverts commit 930f3c014821df423507c878415c7fb4910a454d. The build fails with the following build error: arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init': build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit' make[4]: *** [Makefile:1700: u-boot] Error 1 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: i2c-pxa: remove slaveScott Roberts2020-06-271-1/+0
| | | | | | | | | | | | | | | | Removing i2c pxa slave The i2c-pxa is typically not use in slave mode. It does not make sense to have slave mode enabled by default. Having slave mode enabled prevents the i2c controller from being reset if a real slave device such as an SFP is attached to the i2c-pxa bus and locks it up. Disable slave mode so that the i2c controller can be reset if the bus is locked up. If someone actually has a need for pxa slave mode this can be enabled in kernel config. Signed-off-by: Scott Roberts <ttocsr@gmail.com>
* netifd: replace timesvr with timesrvSukru Senli2020-06-271-1/+7
| | | | | | | | /lib/netifd/dhcp.script: Keep support for 'timesvr' while also supporting 'timesrv' Add log message indicating deprecation of 'timesvr' Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
* uboot-kirkwood: enable sata in nsa310 ubootAlberto Bursi2020-06-271-1/+3
| | | | | | | | | | | | | | | | the uboot of nsa310 cannot use the network chip as it is a realtek on the PCIe lanes and not a Marvell ethernet from the SoC. Therefore tftp is not possible on this device and the only way to install is by loading files from a USB drive. If the USB subsystem is dead there is no way to install OpenWrt. Enable sata support and commands so it can be used as a fallback in case of USB issues. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* base-files: coreutil-sha256sum breaks status codeHuangbin Zhan2020-06-271-1/+1
| | | | | | | | | | | With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''. This is caused due to: different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum") '/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum") "coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum This patch restores for 'sysupgrade' the busybox call to its sha256sum applet. Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
* ubox: add ALTERNATIVESHuangbin Zhan2020-06-261-7/+7
| | | | | | This avoids a conflict with the kmod util from the package feed. Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
* logger: enable alternatives supportHuangbin Zhan2020-06-261-2/+3
| | | | | | Avoid conflict with busybox Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
* kernel: add gpio-amd-fch module descriptionFlorian Eckert2020-06-261-0/+17
| | | | | | Add a module description for the new gpio-amd-fch device driver. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* kernel/leds-apu2: remove deprecated leds-apu2 driverFlorian Eckert2020-06-264-423/+0
| | | | | | | | Remove leds-apu2 out of tree driver. There is a new upstream device gpio and leds driver stack available for the APUv2 and APUv3 boards from pc egnines. This new driver stack was add in kernel version 4.15. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* mac80211: ath9k: enable MFP capability unconditionallyDavid Bauer2020-06-251-0/+34
| | | | | | | | | | ath9k will already fallback on software-crypto for chipsets not supporting IEEE802.11w (MFP). So advertising MFP is not dependent on disabling HW crypto for all traffic entirely. Tested on Sonicwall SonicPoint Ni (AR9132) Signed-off-by: David Bauer <mail@david-bauer.net>
* dropbear: fix compilation for uClibcHans Dedecker2020-06-242-0/+59
| | | | | | | | | | | | | | | Backport patches which fix compile issue for uClibc-ng : dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration] ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK); ^~~~~~~~~ genrandom dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'? ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK); ^~~~~~~~~~~~~ SOCK_NONBLOCK Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* urandom-seed: update MakefileSungbo Eo2020-06-241-5/+3
| | | | | | | | | | - update SPDX license identifier - use https in URL - use default PKG_BUILD_DIR Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz> Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* wireguard: bump to 1.0.20200623Jason A. Donenfeld2020-06-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | * compat: drop centos 8.1 support as 8.2 is now out Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at <https://www.wireguard.com/build-status/>. * Kbuild: remove -fvisibility=hidden from cflags This fixes an issue when compiling wireguard as a module for ARM kernels in THUMB2 mode without the JUMP11 workaround. * noise: do not assign initiation time in if condition Style fix. * device: avoid circular netns references Fixes a circular reference issue with network namespaces. * netns: workaround bad 5.2.y backport This works around a back backport in the 5.2.y series. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* mac80211: fix use of local variableLeon M. George2020-06-241-1/+1
| | | | | | | | | | mac80211_get_addr is called from mac80211_generate_mac, where the local variable initialisation id="${macidx:-0}" suggests that macidx is not always defined. Probably, idx was supposed to be used instead of $(($macidx + 1)). Fixes: 4d99db168cf7 ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set") Signed-off-by: Leon M. George <leon@georgemail.eu>
* base-files: remove urandom-seed definitionSungbo Eo2020-06-231-9/+0
| | | | | | | | urandom-seed has a separate Makefile, we can safely remove the definition here. Fixes: 27bfde9c9f78 ("base-files: move urandom seed bits into separate package") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* igmpproxy: remove some bashismSven Roederer2020-06-231-3/+5
| | | | | | | | | | | | "[[" is a bash extension for test. As the ash-implementation is not fully compatible we drop its usage. This follows up 3519bf4976b41c As a result, we also need to move the and/or out of the test brackets. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [squash from two patches, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* libnetfilter-queue: fix package title and descriptionCatalin Patulea2020-06-231-3/+3
| | | | | | | | | | The original text was copy/pasted from some other package. Adjust the package title and description to match the description on the publishers page. Signed-off-by: Catalin Patulea <catalinp@google.com> [slightly adjust content and commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* dropbear: bump to 2020.79Konstantin Demin2020-06-219-3722/+36
| | | | | | | | | | | | | | | | | | | | | - drop patches (applied upstream): * 010-backport-change-address-logging.patch * 020-backport-ed25519-support.patch * 021-backport-chacha20-poly1305-support.patch - backport patches: * 010-backport-disable-toom-and-karatsuba.patch: reduce dropbear binary size (about ~8Kb). - refresh patches. - don't bother anymore with following config options because they are disabled in upstream too: * DROPBEAR_3DES * DROPBEAR_ENABLE_CBC_MODE * DROPBEAR_SHA1_96_HMAC - explicitly disable DO_MOTD as it was before commit a1099ed: upstream has (accidentally) switched it to 0 in release 2019.77, but reverted back in release 2020.79. Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* toolchain: glibc ldd env path fixupChen Minqiang2020-06-181-0/+1
| | | | | | | | | | This replace the shell script header of ldd when it install to `/usr/bin/ldd` where `#! /..../staging_dir/host/bin/bash` should be `#!/bin/sh` Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* base-files: gpio switch: add named GPIO supportKuan-Yi Li2020-06-183-14/+32
| | | | | | | | | | | | | | | | Previously, gpio_switch only accepts GPIO pin number as input. Once a GPIO pin is exported and named by device tree, its pin state cannot be configured and saved across reboots by UCI. This patch adds support for named GPIO pins. Thus GPIO pin can be exported by device tree with active high/low correctly configured, having human-readable name in /sys/class/gpio/ is also now possible. More importantly, GPIO pins which are referenced by name will be immune from pin mapping breakage while unintentional pin number changes are introduced by kernel or driver updates. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* mac80211: ath9k: enable adding wireless noise to kernel entropy poolAlan Swanson2020-06-181-0/+8
| | | | | | | | | | This option allows adding the ath9k ADC register output as a source of randomness into the Linux entropy pool at sufficient quality random data (at least 10 bits and up to 22 bits of min-entropy for a 32-bit value). Fixes FS#1444 Signed-off-by: Alan Swanson <reiver@improbability.net>
* hostapd: fix compilation of wpa_supplicantKarel Kočí2020-06-181-4/+4
| | | | | | | | | | | | | Ubus patch as it seems have been broken by some rebase in the past as the location of line that adds ubus object file was in condition for CONFIG_MACSEC. That condition was adding object files that are not touched by ubus patch. This means ubus.o does not have to be included in that case. When it has to be and when build fails is when CONFIG_AP is set. All files included in wpa_supplicant that are touched by this patch are in this condition. This means that this is for sure the original place for it. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* toolchain: remove gcc libssp and use libc variantIan Cooper2020-06-171-41/+0
| | | | | | | | | | | | | | | Removes the standalone implementation of stack smashing protection in gcc's libssp in favour of the native implementation available in glibc and uclibc. Musl libc already uses its native ssp, so this patch does not affect musl-based toolchains. Stack smashing protection configuration options are now uniform across all supported libc variants. This also makes kernel-level stack smashing protection available for x86_64 and i386 builds using non-musl libc. Signed-off-by: Ian Cooper <iancooper@hotmail.com>
* comgt-ncm: do not attempt to connect if the control device is invalidRozhuk Ivan2020-06-171-16/+46
| | | | | | | | | | | | | | | | | | | | | | After a hardware reconnect, the control device might be unavailable and attempting to interact with it will lead to hanging gcom calls, leaving the protocol setup in an unrecoverable state. Change the protocol handler to bail out early and notify netifd if the control device is not defined or if the underlying device node does not exist. Also ensure that the "disconnect", "connect" and "setmode" commands are actually defined before trying to invoke them. Finally attempt to re-query the device manufacturer if it is unset in the interface state in order to prevent UNUPPORTED_MODEM errors after a modem hardware reconnect. Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com> [reword subject and commit message] Ref: https://github.com/openwrt/openwrt/pull/2352 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* openvpn: add generic hotplug mechanismFlorian Eckert2020-06-176-8/+81
| | | | | | | | | | | | | | | | | | | Pass a default --up and --down executable to each started OpenVPN instance which triggers /etc/hotplug.d/openvpn/ scripts whenever an instance goes up or down. User-configured up and down scripts are invoked by the default shipped 01-user hotplug handler to ensure that existing setups continue to work as before. As a consequence of this change, the up, down and script_security OpenVPN options are removed from the option file, since we're always passing them via the command line, they do not need to get included into the generated configuration. Signed-off-by: Florian Eckert <fe@dev.tdt.de> [reword commit message, move hotplug executable to /usr/libexec] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uclient: uclient-fetch: add option to read POST data from fileDaniel Golle2020-06-171-3/+3
| | | | | | c660986 uclient-fetch: add option to read POST data from file Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kirkwood: move mmc/sd features to modulesPawel Dembicki2020-06-141-0/+17
| | | | | | | | | | All devices are using nand images. Built-in MMC/SD modules are not needed anymore. Run tested: pogo v4 Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* iproute2: update to 5.7.0Hans Dedecker2020-06-132-2/+48
| | | | | | Update iproute2 to latest stable 5.7.0; for the changes see https://lwn.net/Articles/822152/ Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* hostapd: hostapd_set_psk_file: fix defaut value for macJohann Neuhauser2020-06-131-1/+1
| | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Bringing up of station vlan fails if the optional mac entry isn't set. The default mac "00:00:00:00:00:00", which should match all stations, is mistakenly set to the non used variable "isolate". This results in a wrong formatted .psk file which has to be "vlan_id mac key". fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ipq40xx: add support for EnGenius EMR3500Yen-Ting-Shen2020-06-132-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mtd: enable wrgg support for ath79Stijn Tintel2020-06-111-1/+1
| | | | | | This is required for the D-Link DAP-2695-A1. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* odhcpd: remove bogus IPKG_INSTROOT referenceKevin Darbyshire-Bryant2020-06-112-2/+2
| | | | | | | | | IPKG_INSTROOT is only set under image builder and we won't be running this script at build time either, so remove the reference before it gets cargo-culted into other scripts. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* soloscli: fix uci-defaults fileAdrian Schmutzler2020-06-112-3/+1
| | | | | | | | | | The folder for the uci-defaults file of this package is wrong, so the file most probably has not been executed at all for several years at least. Fix the folder and remove the useless shebang for the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the Netgear WNDRMAC v1Renaud Lepage2020-06-111-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2 Specifications ============== * SoC: Atheros AR7161 * RAM: 64mb * Flash on board: 16mb * WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n) * Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit) * Power: 12 VDC, 2.5 A * Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1) Flash Instructions ================== It is possible to use the OEM Upgrade page to install the `factory` variant of the firmware. After the initial upgrade, you will need to telnet into the router (default IP 192.168.1.1) to install anything. You may install LuCI this way. At this point, you will have a web interface to configure OpenWRT on the WNDRMAC v1. Please use the `sysupgrade` variant for subsequent flashes. Recovery Instructions ===================== A TFTP-based recovery flash is possible if the need arises. Please refer to the WNDR3700 page on openwrt.org for details. https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery Signed-off-by: Renaud Lepage <root@cybikbase.com> [update DTSI include name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* netifd: disable receive packet steering for DSA slave devicesFelix Fietkau2020-06-101-4/+9
| | | | | | | It is already handled on the master device. Doing it twice reduces performance Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: enable hostapd 802.11ax support if kmod-mt7915e is selectedFelix Fietkau2020-06-101-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add config symbol for allowing drivers to enable 802.11ax supportFelix Fietkau2020-06-103-0/+14
| | | | | | Also expose a build feature for it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ca-certificates: update to version 20200601Christian Lamparter2020-06-091-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch updates the ca-certificates and ca-bundle package. This version changed the files directory again, to work/, so PKG_BUILD_DIR was brought back. A list of changes from Debian's change-log entry for 20200601 [0]: * mozilla/{certdata.txt,nssckbi.h}: Update Mozilla certificate authority bundle to version 2.40. Closes: #956411, #955038 * mozilla/blacklist.txt Add distrusted Symantec CA list to blacklist for explicit removal. Closes: #911289 Blacklist expired root certificate, "AddTrust External Root" Closes: #961907 The following certificate authorities were added (+): + "Certigna Root CA" + "emSign ECC Root CA - C3" + "emSign ECC Root CA - G3" + "emSign Root CA - C1" + "emSign Root CA - G1" + "Entrust Root Certification Authority - G4" + "GTS Root R1" + "GTS Root R2" + "GTS Root R3" + "GTS Root R4" + "Hongkong Post Root CA 3" + "UCA Extended Validation Root" + "UCA Global G2 Root" The following certificate authorities were removed (-): - "AddTrust External Root" - "Certinomis - Root CA" - "Certplus Class 2 Primary CA" - "Deutsche Telekom Root CA 2" - "GeoTrust Global CA" - "GeoTrust Primary Certification Authority" - "GeoTrust Primary Certification Authority - G2" - "GeoTrust Primary Certification Authority - G3" - "GeoTrust Universal CA" - "thawte Primary Root CA" - "thawte Primary Root CA - G2" - "thawte Primary Root CA - G3" - "VeriSign Class 3 Public Primary Certification Authority - G4" - "VeriSign Class 3 Public Primary Certification Authority - G5" - "VeriSign Universal Root Certification Authority" [0] <https://metadata.ftp-master.debian.org/changelogs//main/c/ca-certificates/ca-certificates_20200601_changelog> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* hostapd: update to latest Git hostap_2_9-1331-g5a8b366233f5Petr Štetiar2020-06-0923-113/+113
| | | | | | | | | | | | | Bump to latest Git and refresh all patches in order to get fix for "UPnP SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695). General security vulnerability in the way the callback URLs in the UPnP SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695). Some of the described issues may be applicable to the use of UPnP in WPS AP mode functionality for supporting external registrars. Ref: https://w1.fi/security/2020-1/ Signed-off-by: Petr Štetiar <ynezz@true.cz>
* umdnsd: update to latest git HEADKevin Darbyshire-Bryant2020-06-081-3/+3
| | | | | | | | d13290b Fix advertised IPv6 addresses Don't just serve link-local addresses via mdns, offer all. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* hostapd: silence rmStijn Tintel2020-06-081-2/+2
| | | | | | | | | | | | When bringing up wifi the first time after boot, these warnings appear: netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory Silence them by adding the "-f" option to rm. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* bcm27xx-gpu-fw: bump to most recent good versionStijn Tintel2020-06-071-14/+14
| | | | | | | | This updates to the last firmware version before the switch to building from the common firmware branch, which introduces various issues. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Revert "bcm27xx-gpu-fw: update to latest version"Stijn Tintel2020-06-071-15/+15
| | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 9e467a764b4e30a04dd0431ea277f6acd26babe0. The Raspberry Pi firmware recently switched to building from the common firmware branch. This introduces changes in the core clock handling, causing various issues. E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz. When the disable-bt DT overlay is not loaded, the core clock frequency is increased to 400MHz. As a result, the UART baud rate is no longer correct, and this causes garbled serial console, or communication problems with HATs that use the UART. As a workaround, the core clock could be fixed to 250MHz by adding 'core_freq=250' in /boot/config.txt, but as there appear to be other issues than just the UART being broken, the safer bet is to revert the firmware for now. Upstream bug: https://github.com/raspberrypi/firmware/issues/1376 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
* netifd: update to latest git HEADHans Dedecker2020-06-061-3/+3
| | | | | | 51e9fb8 system-linux: improve handling of device rename Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* kernel: Add kmod-sch-cake-virtual intermediate packageToke Høiland-Jørgensen2020-06-061-3/+15
| | | | | | | | | | | | As reported in https://github.com/openwrt/packages/issues/12072, the imagebuilder fails due to a dependency resolution error when the userspace packages are built using a target that has a different kernel version than that which is being run. To resolve this, add a virtual kernel package with the conditional dependency currently used in sqm-scripts. The idea is to move the sqm-scripts dependency to this virtual package, which hopefully should be consistent with the actual kernel module being built. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
* nghttp2: bump to 1.41.0Hans Dedecker2020-06-061-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8f7b008b Update bash_completion 83086ba9 Update manual pages c3b46625 Merge pull request from GHSA-q5wr-xfw9-q7xr 3eecc2ca Bump version number to v1.41.0, LT revision to 34:0:20 881c060d Update AUTHORS f8da73bd Earlier check for settings flood 336a98fe Implement max settings option ef415836 Revert "Add missing connection error handling" 979e6c53 Merge pull request #1459 from nghttp2/proxyprotov2 b7d16101 Add missing connection error handling cd53bd81 Merge pull request #1460 from gportay/patch-1 e5625b8c Fix doc c663349f integration: Add PROXY protocol v2 tests 854e9fe3 nghttpx: Always call init_forwarded_for c60ea227 Update doc 49cd8e6e nghttpx: Add PROXY-protocol v2 support 3b17a659 Merge pull request #1453 from Leo-Neat/master 600fcdf5 Merge pull request #1455 from xjtian/long_serials 4922bb41 static_cast size parameter in StringRef constructor to size_t aad86975 Fix get_x509_serial for long serial numbers dc7a7df6 Adding CIFuzz b3f85e2d Merge pull request #1444 from nghttp2/fix-recv-window-flow-control-issue ffb49c6c Merge pull request #1435 from geoffhill/master 2ec58551 Fix receiving stream data stall 459df42b Merge pull request #1442 from nghttp2/upgrade-llhttp a4c1fed5 Bump llhttp to 2.0.4 866eadb5 Enable session_create_idle_stream test, fix errors 5e13274b Fix typo e0d7f7de h2load: Allow port in --connect-to df575f96 h2load: add --connect-to option 1fff7379 clang-format-9 b40c6c86 Merge pull request #1418 from vszakats/patch-1 9bc2c75e lib/CMakeLists.txt: Make hard-coded static lib suffix optional 2d5f7659 Bump up version number to 1.41.0-DEV Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mvebu: rename Linksys devices based on their common namesPaul Spooren2020-06-051-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys devices in mvebu target feature a mixed naming, where parts are based on the official product name (device node, image; e.g. WRT3200ACM) and parts are based on the internal code name (DTS file name, compatible, LED labels; e.g. rango). This inconsistent naming has been perceived as quite confusing. A recent attempt by Paul Spooren to harmonize this naming in kernel has been declined there. However, for us it still makes sense to apply at least a part of these changes locally. Primarily, this patch changes the compatible in DTS and thus the board name used in various scripts to have them in line with the device, model and image names. Due to the recent switch from swconfig to DSA, this allows us to drop SUPPORTED_DEVICES and thus prevent seamless upgrade between these incompatible setups. However, this does not include the LED label rename from Paul's initial patch: I don't think it's worth keeping the enormous diff locally for this case, as we can implement this much easier in 01_leds if we have to live with the inconsistency anyway. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, extend to all devices, drop DT LED changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-16 14:13:55 +0000