aboutsummaryrefslogtreecommitdiffstats
path: root/package/network/services/hostapd
Commit message (Collapse)AuthorAgeFilesLines
* hostapd: pass respawn settings when registering the serviceJohn Crispin2020-12-221-2/+2
| | | | | | | | When hostapd gets restarted to often/quickly will cause procd to not restart it anymore. it will think that hapd is in a crash loop. Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
* hostapd: Use EAPOLv1 (802.1X-2001) if WPA enabledNick Lowe2020-12-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, EAPOLv2 (802.1X-2004) is used by default for legacy clients that are not WPA2 (RSN) capable. These legacy clients are often intolerant to this EAPOL version and fail to connect. hostapd.conf upstream documents for eapol_version the following and that this is a known compatibility issue with version 2: // IEEE 802.1X/EAPOL version // hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL // version 2. However, there are many client implementations that do not handle // the new version number correctly (they seem to drop the frames completely). // In order to make hostapd interoperate with these clients, the version number // can be set to the older version (1) with this configuration value. // Note: When using MACsec, eapol_version shall be set to 3, which is // defined in IEEE Std 802.1X-2010. //eapol_version=2 For the wpa parameter, hostapd.conf upstream documents that this is a bitfield, configured as follows: // Enable WPA. Setting this variable configures the AP to require WPA (either // WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either // wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. // Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. // For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), // RADIUS authentication server must be configured, and WPA-EAP must be included // in wpa_key_mgmt. // This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) // and/or WPA2 (full IEEE 802.11i/RSN): // bit0 = WPA // bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) // Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2. // In other words, for WPA3, wpa=2 is used the configuration (and // wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK). //wpa=2 For client compatibility therefore: EAPOLv1 (802.1X-2001) should be used by default where WPA is enabled. EAPOLv2 (802.1X-2004) should be used by default where WPA is disabled. To fix this, we can therefore change in the script: set_default eapol_version 0 To the following: set_default eapol_version $((wpa & 1)) This therefore: 1) Sets eapol_version to 1 where WPA has been enabled via wpa bit0 being set. 2) Sets eapol_version to 0 where WPA has been disabled via wpa bit0 being unset. For usual configurations that only have WPA2 enabled, EAPOLv2 is then used. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* hostapd: parse skip_inactivity_poll optionNadim Atiya2020-12-222-3/+5
| | | | | | | | | | | | hostapd.sh does not parse skip_inactivity_poll boolean from /etc/config/wireless despite being mentioned in the documentation [1]. This change fixes this, and by default sets its value to 0 [1]. [1] https://openwrt.org/docs/guide-user/network/wifi/basic Signed-off-by: Nadim Atiya <nadim.atiya@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [fix and reformat commit message, make patch apply]
* hostapd: Disable 802.11b data rates by defaultNick Lowe2020-12-062-2/+2
| | | | | | | | | | | | | | | | | Set legacy_rates to 0 by default to disable 802.11b data rates by default. The time has long come where 802.11b DSSS/CCK data rates should be disabled by default in OpenWRT. Users in need of 802.11b client support can reasonably enable these where they are needed. The balance of equities has significantly, and for a long time, tipped such that dropping backwards compatibility by default with 802.11b devices is appropriate, proportionate and justified. By doing so, management and control traffic is moved by default to a 20 MHz wide 6 Mb/s OFDM data rate instead of a 22 MHz wide 1 Mb/s DSSS data rate. This is significantly more airtime efficient. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* hostapd: Add cell_density data rates optionNick Lowe2020-11-301-13/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a cell_density option to configure data rates for normal, high and very high cell density wireless deployments. The purpose of using a minimum basic/mandatory data rate that is higher than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density environments is to transmit broadcast/multicast data frames using less airtime or to reduce management overheads where significant co-channel interference (CCI) exists and cannot be avoided. Caution: Without careful design and validation, configuration of a too high minimum basic/mandatory data rate can sacrifice connection stability or disrupt the ability to reliably connect and authenticate for little to no capacity benefit. This is because this configuration affects the ability of clients to hear and demodulate management, control and broadcast/multicast data frames. Deployments that have not been specifically designed and validated are usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data rates. Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b compatible), minimum basic/mandatory rate in high cell density deployments that have been designed and validated for this. For many deployments, the minimum basic/mandatory data rate should not be configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a configuration is only appropriate for use in very high cell density deployment scenarios. A cell_density of Very High (3) should only be used where a deployment has a valid use case and has been designed and validated specifically for this use, nearly always with highly directional antennas - an example would be stadium deployments. For example, with a 24 Mb/s OFDM minimum basic/mandatory data rate, approximately a -73 dBm RSSI is required to decode frames. Many clients will not have roamed elsewhere by the time that they experience -73 dBm and, where they do, they frequently may not hear and be able to demodulate beacon, control or broadcast/multicast data frames causing connectivity issues. There is a myth that disabling lower basic/mandatory data rates will improve roaming and avoid sticky clients. For 802.11n, 802.11ac and 802.11ax clients this is not correct as clients will shift to and use lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are able to be used as basic/mandatory data rates. There is a myth that disabling lower basic/mandatory data rates will ensure that clients only use higher data rates and that better performance is assured. For 802.11n, 802.11ac and 802.11ax clients this is not correct as clients will shift around and use MCS rates and not the 802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory data rates. Cell Density 0 - Disabled (Default) Setting cell_density to 0 does not configure data rates. This is the default. 1 - Normal Cell Density Setting cell_density to 1 configures the basic/mandatory rates to 6, 12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting cell_density to 1 configures the basic/mandatory rates to the 5.5 and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower than the minimum basic/mandatory rate are not offered. 2 - High Cell Density Setting the cell_density to 2 configures the basic/mandatory rates to the 12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting the cell_density to 2 configures the basic/mandatory rates to the 11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the minimum basic/mandatory rate are not offered. 3 - Very High Cell Density Setting the cell_density to 3 configures the basic/mandatory rates to the 24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the minimum basic/mandatory rate are not offered. Setting the cell_density to 3 only has effect where legacy_rates is 0, else this has the same effect as being configured with a cell_density of 2. Where specified, the basic_rate and supported_rates options continue to override both the cell_density and legacy_rates options. Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
* hostapd: fix "sh: out of range" errorsStijn Tintel2020-11-261-0/+7
| | | | | | | | | | | | | | Several variables in hostapd.sh can be used uninitialized in numerical comparisons, causing errors in logread: netifd: radio24 (1668): sh: out of range Set defaults for those variables to silence those errors. Fixes: b518f07d4b8a ("hostapd: remove ieee80211v option") Fixes: cc80cf53c50d ("hostapd: add FTM responder support") Fixes: e66bd0eb0469 ("hostapd: make rrm report independent of ieee80211k setting") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* hostapd: fix patch offsetLeon M. George2020-11-231-1/+1
| | | | | | | Fixes the offset of the patch added in 93bbd998aa696a ("hostapd: enter DFS state if no available channel is found"). Signed-off-by: Leon M. George <leon@georgemail.eu>
* hostapd: enable the epoll-based event loopRui Salvaterra2020-11-238-8/+8
| | | | | | Hostapd supports epoll() since 2014. Let's enable it for better performance. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: set validity interval for BSS TMRADavid Bauer2020-11-171-1/+1
| | | | | | | | | | | | This sets the validity interval for the BSS transition candidate list to the same value as the disassociation timer. Currently the value is always 0, which is the specification states is a reserved value. Also, wpa_supplicant and from the looks of it some Android implementations will outright ignore the candidate list in this case. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add support for static airtime policy configurationDobroslaw Kijowski2020-11-172-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add support for passing airtime_sta_weight into hostapd configuration. * Since that commit it is possible to configure station weights. Set higher value for larger airtime share, lower for smaller share. I have tested this functionality by modyfing /etc/config/wireless to: config wifi-device 'radio0' ... option airtime_mode '1' config wifi-iface 'default_radio0' ... list airtime_sta_weight '01:02:03:04:05:06 1024' Now, when the station associates with the access point it has been assigned a higher weight value. root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime RX: 12656 us TX: 10617 us Weight: 1024 Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us [MAC address has been changed into a dummy one.] Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
* hostapd: fix per-BSS airtime configurationDobroslaw Kijowski2020-11-172-1/+3
| | | | | | | | airtime_mode is always parsed as an empty string since it hasn't been added into hostapd_common_add_device_config function. Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration") Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
* hostapd: ubus: add get_status methodDavid Bauer2020-11-171-0/+40
| | | | | | | This adds a new get_status method to a hostapd interface, which provides information about the current interface status. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add VHT capabilities to client listDavid Bauer2020-11-171-0/+71
| | | | | | | This adds parsed VHT capability information to the hostapd get_clients method. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add driver information to client listDavid Bauer2020-11-171-0/+24
| | | | | | | | This adds information from mac80211 to hostapd get_client ubus function. This way, TX as well as RX status information as well as the signal can be determined. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: fix variable shadowingDavid Bauer2020-11-171-0/+2
| | | | | | Fixes commit 838b412cb527 ("hostapd: add interworking support") Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add a hostapd-basic-wolfssl variantRui Salvaterra2020-11-081-0/+13
| | | | | | | | | | | | If only AP mode is needed, this is currently the most space-efficient way to provide support for WPA{2,3}-PSK, 802.11w and 802.11r. openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin sizes: 4719426 bytes (with wpad-basic-wolfssl) 4457282 bytes (with hostapd-basic-wolfssl) Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: enable OWE for the basic-{openssl, wolfssl} variantsRui Salvaterra2020-10-311-0/+6
| | | | | | | Opportunistic Wireless Encryption is needed to create/access encrypted networks which don't require authentication. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: remove hostapd-hs20 variantDaniel Golle2020-10-301-18/+0
| | | | | | | | Hotspot 2.0 AP features have been made available in the -full variants of hostapd and wpad. Hence we no longer need a seperate package for that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add {hostapd,wpad}-basic-openssl variantsRui Salvaterra2020-10-302-0/+28
| | | | | | | | | Add OpenSSL-linked basic variants (which provides WPA-PSK only, 802.11r and 802.11w) of both hostapd and wpad. For people who don't need the full hostapd but are stuck with libopenssl for other reasons, this saves space by avoiding the need of an additional library (or a larger hostapd with built-in crypto). Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: wpas: add missing config symbolsDavid Bauer2020-10-282-3/+3
| | | | | | | | | | | | | | | This adds missing config symbols for interworking as well as Hotspot 2.0 to the wpa_supplicant-full configuration. These symbols were added to the hostapd-full configuration prior to this commit. Without adding them to the wpa_supplicant configuration, building of wpad-full fails. Thanks to Rene for reaching out on IRC. Fixes: commit be9694aaa297 ("hostapd: add UCI support for Hotspot 2.0") Fixes: commit 838b412cb527 ("hostapd: add interworking support") Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: bump PKG_RELEASEDavid Bauer2020-10-281-1/+1
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add interworking supportDavid Bauer2020-10-282-1/+79
| | | | | | | | | | | | | | | | | | | | | | | | This adds configuration options to enable interworking for hostapd. All options require iw_enabled to be set to 1 for a given VAP. All IEEE802.11u related settings are supported with exception of the venue information which will be added as separate UCI sections at a later point. The options use the same name as the ones from the hostapd.conf file with a "iw_" prefix added. All UCI configuration options are passed without further modifications to hostapd with exceptions of the following options, whose elements can be provided using UCI lis elements: - iw_roaming_consortium - iw_anqp_elem - iw_nai_realm - iw_domain_name - iw_anqp_3gpp_cell_net Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add FTM responder supportDavid Bauer2020-10-281-0/+13
| | | | | | | | | | | | | | | This adds support for enabling the FTM responder flag for the APs extended capabilities. On supported hardware, enabling the ftm_responder config key for a given AP will enable the FTM responder bit. FTM support itself is unconditionally implemented in the devices firmware (ath10k 2nd generation with 3.2.1.1 firmware). There's currently no softmac implementation. Also allow to configure LCI and civic location information which can be transmitted to a FTM initiator. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: remove ieee80211v optionDavid Bauer2020-10-281-14/+6
| | | | | | | | | | | | | Remove the ieee80211v option. It previously was required to be enabled in order to use time_advertisement, time_zone, wnm_sleep_mode and bss_transition, however it didn't enable any of these options by default. Remove it, as configuring these options independently is enough. This change does not influence the behavior of any already configured setting. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: make rrm report independent of ieee80211k settingDavid Bauer2020-10-281-5/+4
| | | | | | | | Allow to configure both RRM beacon as well as neighbor reports independently and only enable them by default in case the ieee80211k config option is set. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: add handler for wps_status and guard WPS callsDaniel Golle2020-10-163-1/+57
| | | | | | | | | Expose WPS ubus API only if compiled with WPS support and add new handler for wps_status call. Also add '-v wps' option to check whether WPS support is present in hostapd. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: add support for specifying a per-device scan listFelix Fietkau2020-09-291-0/+1
| | | | | | | This is useful to bring up multiple client mode interfaces on a single channel much faster without having to scan through a lot of channels Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: ubus: make (B)SSID optional for neighbor reportDavid Bauer2020-09-222-10/+25
| | | | | | | | | | | Make the BSSID and SSID fields optional when configuring a neighbor report into hostapd. Both options can now be an empty string. For the BSSID, the first 6 byte are copied from the neighbor report. For the SSID, the SSID for the affected hostapd BSS is used. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: send notification instead of eventDavid Bauer2020-09-222-12/+13
| | | | | | | | | | | Rafal Milecki pointed out that ubus events are meant for low-level ubus events only (e.g. addition or removal of an object). Higher level events should happen as notifications on the ubus object itself. Dispatch BSS events on the main hostapd ubus object instead of publishing them as ubus events. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: ubus: fix infinite loop when configuring RRM NRDavid Bauer2020-09-212-3/+2
| | | | | | | The return-code was set, however it was never returned, nor was the loop interrupted. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: send procd event on BSS updateDavid Bauer2020-09-212-4/+36
| | | | | | | Dispatch ubus events also to procd in order to trigger service reloads on hostapd updates. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: send ubus event on BSS updateDavid Bauer2020-09-212-2/+24
| | | | | | | | | | | hostapd will emit a ubus event with the eventname hostapd.<ifname>.<event> when adding, removing or reloading a BSS. This way, services which install state (for example the RMM neighbor list) can on-demand reinstall this information for the BSS without polling this state. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add support for per-BSS airtime configurationDavid Bauer2020-09-113-4/+14
| | | | | | | | | | | | Add support for per-BSS airtime weight configuration. This allows to set a airtime weight per BSS as well as a ratio limit based on the weight. Support for this feature is only enabled in the full flavors of hostapd. Consult the hostapd.conf documentation (Airtime policy configuration) for more information on the inner workings of the exposed settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add UCI support for Hotspot 2.0Daniel Golle2020-09-083-3/+107
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add hs20 variantDaniel Golle2020-09-011-1/+21
| | | | | | Add hostapd variant compiled with support for Hotspot 2.0 AP features. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: Fix compile errors after wolfssl updateHauke Mehrtens2020-08-271-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the following compile errors after the wolfssl 4.5.0 update: LD wpa_cli ../src/crypto/tls_wolfssl.c: In function 'tls_match_alt_subject': ../src/crypto/tls_wolfssl.c:610:11: error: 'GEN_EMAIL' undeclared (first use in this function); did you mean 'ENAVAIL'? type = GEN_EMAIL; ^~~~~~~~~ ENAVAIL ../src/crypto/tls_wolfssl.c:610:11: note: each undeclared identifier is reported only once for each function it appears in ../src/crypto/tls_wolfssl.c:613:11: error: 'GEN_DNS' undeclared (first use in this function) type = GEN_DNS; ^~~~~~~ ../src/crypto/tls_wolfssl.c:616:11: error: 'GEN_URI' undeclared (first use in this function) type = GEN_URI; ^~~~~~~ ../src/crypto/tls_wolfssl.c: In function 'wolfssl_tls_cert_event': ../src/crypto/tls_wolfssl.c:902:20: error: 'GEN_EMAIL' undeclared (first use in this function); did you mean 'ENAVAIL'? if (gen->type != GEN_EMAIL && ^~~~~~~~~ ENAVAIL ../src/crypto/tls_wolfssl.c:903:20: error: 'GEN_DNS' undeclared (first use in this function) gen->type != GEN_DNS && ^~~~~~~ ../src/crypto/tls_wolfssl.c:904:20: error: 'GEN_URI' undeclared (first use in this function) gen->type != GEN_URI) ^~~~~~~ Makefile:2029: recipe for target '../src/crypto/tls_wolfssl.o' failed Fixes: 00722a720c77 ("wolfssl: Update to version 4.5.0") Reported-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* hostapd: recognize option "key" as alias for "auth_secret"Jo-Philipp Wich2020-08-072-2/+2
| | | | | | | | | | | | | | The hostapd configuration logic is supposed to accept "option key" as legacy alias for "option auth_secret". This particular fallback option failed to work though because "key" was not a registered configuration variable. Fix this issue by registering the "key" option as well, similar to the existing "server" nad "port" options. Ref: https://github.com/openwrt/openwrt/pull/3282 Suggested-by: Michael Jones <mike@meshplusplus.com> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* hostapd: make "key" option optional if "wpa_psk_file" is providedJo-Philipp Wich2020-08-071-5/+5
| | | | | | | | | | | | | If an existing "wpa_psk_file" is passed to hostapd, the "key" option may be omitted. While we're at it, also improve the passphrase length checking to ensure that it is either exactly 64 bytes or 8 to 63 bytes. Fixes: FS#2689 Ref: https://github.com/openwrt/openwrt/pull/3283 Suggested-by: Michael Jones <mike@meshplusplus.com> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* hostapd: add wpad-basic-wolfssl variantPetr Štetiar2020-08-072-0/+16
| | | | | | | | | Add package which provides size optimized wpad with support for just WPA-PSK, SAE (WPA3-Personal), 802.11r and 802.11w. Signed-off-by: Petr Štetiar <ynezz@true.cz> [adapt to recent changes, add dependency for WPA_WOLFSSL config] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: fix incorrect service nameDavid Bauer2020-07-311-1/+1
| | | | | | | | | | | | | | When retrieving the PID for hostapd and wpa_supplicant via ubus the wrong service name is currently used. This leads to the following error in the log: netifd: radio0 (1409): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process path (/proc/exe) Fixing the service name retrieves the correct PID and therefore the warning won't occur. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: reorganize config selection hierarchy for WPA3Adrian Schmutzler2020-07-311-16/+18
| | | | | | | | | | | | | | | | | | The current selection of DRIVER_MAKEOPTS and TARGET_LDFLAGS is exceptionally hard to read. This tries to make things a little easier by inverting the hierarchy of the conditions, so SSL_VARIANT is checked first and LOCAL_VARIANT is checked second. This exploits the fact that some of the previous conditions were unnecessary, e.g. there is no hostapd-mesh*, so we don't need to exclude this combination. It also should make it a little easier to see which options are actually switched by SSL_VARIANT and which by LOCAL_VARIANT. The patch is supposed to be cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: improve TITLE for packagesAdrian Schmutzler2020-07-301-27/+33
| | | | | | | | | | | | | | For a few packages, the current TITLE is too long, so it is not displayed at all when running make menuconfig. Despite, there is no indication of OpenSSL vs. wolfSSL in the titles. Thus, this patch adjusts titles to be generally shorter, and adds the SSL variant to it. While at it, make things easier by creating a shared definition for eapol-test like it's done already for all the other flavors. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: update mesh DFS patches and add mesh HE supportDaniel Golle2020-07-3034-190/+1440
| | | | | | | | | | | | | | | | Drop outdated and by now broken patchset originally supplied by Peter Oh in August 2018 but never merged upstream. Instead add the more promissing rework recently submitted by Markus Theil who picked up Peter's patchset, fixed and completed it and added support for HE (802.11ax) in mesh mode. This is only compile tested and needs some real-life testing. Fixes: FS#3214 Fixes: 167028b750 ("hostapd: Update to version 2.9 (2019-08-08)") Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed") Fixes: 017320ead3 ("hostapd: bring back mesh patches") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: enter DFS state if no available channel is foundDavid Bauer2020-07-201-0/+37
| | | | | | | | | | | Previously hostapd would not stop transmitting when a DFS event was detected and no available channel to switch to was available. Disable and re-enable the interface to enter DFS state. This way, TX does not happen until the kernel notifies hostapd about the NOP expiring. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: fix compilation of wpa_supplicantKarel Kočí2020-06-181-4/+4
| | | | | | | | | | | | | Ubus patch as it seems have been broken by some rebase in the past as the location of line that adds ubus object file was in condition for CONFIG_MACSEC. That condition was adding object files that are not touched by ubus patch. This means ubus.o does not have to be included in that case. When it has to be and when build fails is when CONFIG_AP is set. All files included in wpa_supplicant that are touched by this patch are in this condition. This means that this is for sure the original place for it. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* hostapd: hostapd_set_psk_file: fix defaut value for macJohann Neuhauser2020-06-131-1/+1
| | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Bringing up of station vlan fails if the optional mac entry isn't set. The default mac "00:00:00:00:00:00", which should match all stations, is mistakenly set to the non used variable "isolate". This results in a wrong formatted .psk file which has to be "vlan_id mac key". fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* hostapd: add config symbol for allowing drivers to enable 802.11ax supportFelix Fietkau2020-06-103-0/+14
| | | | | | Also expose a build feature for it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: update to latest Git hostap_2_9-1331-g5a8b366233f5Petr Štetiar2020-06-0923-113/+113
| | | | | | | | | | | | | Bump to latest Git and refresh all patches in order to get fix for "UPnP SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695). General security vulnerability in the way the callback URLs in the UPnP SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695). Some of the described issues may be applicable to the use of UPnP in WPS AP mode functionality for supporting external registrars. Ref: https://w1.fi/security/2020-1/ Signed-off-by: Petr Štetiar <ynezz@true.cz>
* hostapd: silence rmStijn Tintel2020-06-081-2/+2
| | | | | | | | | | | | When bringing up wifi the first time after boot, these warnings appear: netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory Silence them by adding the "-f" option to rm. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* hostapd: add support for wifi-station and wifi-vlan sectionsJohn Crispin2020-06-041-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for 2 new uci sections. config wifi-vlan # iface is optional. if it is not defined the vlan will apply # to all interfaces option iface default_radio0 option name guest option vid 100 option network guest config wifi-station # iface is optional. if it is not defined the station will apply # to all interfaces option iface default_radio0 # mac is optional. if it is not defined it will be a catch all # for any sta using this key option mac '00:11:22:33:44:55' # vid is optional. if it is not defined, the sta will be part of # the primary iface. option vid 100 option key testtest With this patch applied it is possible to use multiple PSKs on a single BSS. Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-04 01:19:23 +0000