aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ath79: proper indentation in image/common-tp-link.mkPaul Wassi2019-02-141-1/+1
| | | | | | Add two spaces for proper indentation in image/common-tp-link.mk Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix port order on TL-WR841ND-v7Paul Wassi2019-02-141-3/+3
| | | | | | | | The switch ports are seen one to one on the case. Also remove unneeded secondary port numbers in this case statement. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: change ledtrig on GL.iNet AR150Paul Wassi2019-02-141-1/+1
| | | | | | | | | Change the ledtrig for LAN from netdev to switch. Although eth1 comes out of the device at a single port, this port is a switch-port and therefore the LED must be triggered by that. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TP-LINK to TP-LinkPaul Wassi2019-02-146-34/+34
| | | | | | Remove inconsistencies in the vendor's name. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-MR3220-v2 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+5
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TL-WR740ND-v4 to TL-WR740N-v4Paul Wassi2019-02-144-7/+7
| | | | | | Give the device the same name it had in ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kernel: bump 4.19 to 4.19.21Koen Vandeputte2019-02-146-81/+15
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0007-ARM-dts-Fix-up-the-D-Link-DIR-685-MTD-partition-info.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-1433-121/+71
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.156Koen Vandeputte2019-02-143-9/+9
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* dnsmasq: add rapid commit config optionHans Dedecker2019-02-132-1/+2
| | | | | | | Add config option rapidcommit to enable support for DHCPv4 rapid commit (RFC4039) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* openssl: add package for openssl.cnf, misc changesEneas U de Queiroz2019-02-122-8/+28
| | | | | | | | | | | | - Add the /etc/ssl/openssl.cnf as a separate package, to avoid breaking the transitional mechanism, allowing libopenssl_1.0* and libopenssl_1.1* to coexist. - Remove the (selecting) dependency on @KERNEL_AIO - Use global SOURCE_DATE_EPOCH Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* openssl: optimizations based on ARCH/small flashEneas U de Queiroz2019-02-123-1/+98
| | | | | | | | | | | | | | | | | | | Add a patch to enable the option to change the default ciphersuite list ordering to prefer ChaCha20 over AES-GCM. This is used by default for all platforms, except for x86_64 and aarch64. The assumption is that only the latter have AES-specific CPU instructions and asm code that uses them in openssl. Chacha20Poly1305 is 3x faster than AES-256 in systems without AES instructions, with an equivalent strength. Disable error messages by default except for devices with small flash or RAM, to aid debugging. Disable ASM by default on arm platform with small flash. Size difference on mips and powerpc, the other platforms with small flash devices, are not really relevant (using 100K as a threshold). All of the affected platforms are source-only anyway. Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* openssl: update to version 1.1.1aEneas U de Queiroz2019-02-1222-492/+774
| | | | | | | | | | | | | | | | | | | | | | | This version adds the following functionality: * TLS 1.3 * AFALG engine support for hardware accelleration * x25519 ECC curve support * CRIME protection: disable use of compression by default * Support for ChaCha20 and Poly1305 Patches fixing bugs in the /dev/crypto engine were applied, from https://github.com/openssl/openssl/pull/7585 This increses the size of the ipk binray on MIPS32 by about 32%: old: 693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk 193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk new: 912.493 bin/packages/mips_24kc/base/libopenssl1.1_1.1.1a-2_mips_24kc.ipk 239.316 bin/packages/mips_24kc/base/openssl-util_1.1.1a-2_mips_24kc.ipk Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* openssl: add configuration options, disable ssl3Eneas U de Queiroz2019-02-1214-476/+376
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds the following configuration options: * using optimized assembler code (was always on before) * use of x86 SSE2 instructions * dyanic engine support * include error messages * Camellia, Gost, Idea, MDC2, Seed & Whirlpool algorithms * RFC3779, CMS protocols * VIA padlock hardware acceleration engine Installs openssl.cnf with the library as it is used by engines independent of the openssl util. Fixes DTLS option that was innefective before. Disables insecure SSL3 protocol and SHA0. Adds openwrt-specific targets to Configure script, including asm support for i386, ppc and mips64. Strips building dirs from CFLAGS shown in binary. Skips the fuzz directory during build. Removed include/crypto/devcrypto.h that was included here, to use the cryptodev-linux package, now that it was been moved from the packages feed to the main openwrt repository. This decreses the size of the ipk binray on MIPS32 by about 3.3%: old: 706.957 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk 199.294 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk new: 693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk 193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
* base-files: fix ucert verificationFelix Fietkau2019-02-121-1/+2
| | | | | | | | ucert needs to check the firmware part with metadata, but without the signature. Use the new fwtool mode to extract that without altering the firmware image inside the check Signed-off-by: Felix Fietkau <nbd@nbd.name>
* fwtool: add support for extracting the truncated data part to stdoutFelix Fietkau2019-02-121-2/+23
| | | | | | | This allows extracing the firmware + metadata from a signed firmware without altering the original image file Signed-off-by: Felix Fietkau <nbd@nbd.name>
* fwtool: do not strip metadata if extracting signatureFelix Fietkau2019-02-121-1/+3
| | | | | | This allows the signature to cover the metadata area Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: fix race condition in mesh new peer handlingFelix Fietkau2019-02-121-0/+34
| | | | | | Avoid trying to add the same station to the driver multiple times Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: send wpa_supplicant logging output to syslogFelix Fietkau2019-02-121-1/+1
| | | | | | Helpful for debugging network connectivity issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: brcmfmac: backport early changes queued for the Linux 5.1Rafał Miłecki2019-02-1211-3/+2715
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mac80211: brcmfmac: backport remaining patches from the Linux 5.0Rafał Miłecki2019-02-1214-3/+1071
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* iproute2: tc: reduce size of dynamic symbol tableTony Ambardar2019-02-112-1/+45
| | | | | | | | | | | In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all* symbols into the dynamic symbol table. Instead, use --dynamic-list to export a smaller set of symbols similar to that defined in static-syms.h in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase. Also increment PKG_RELEASE. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: tc: enable and fix support for using .so pluginsTony Ambardar2019-02-112-1/+107
| | | | | | | | | | | | | | | | | | | | | | | This enables using the tc module m_xt.so, which uses the act_ipt kernel module to allow tc actions based on iptables targets. e.g. tc filter add dev eth0 parent 1: prio 10 protocol ip \ u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE Make the SHARED_LIBS parameter configurable and based on tc package selection. Fix a problem using the tc m_xt.so plugin as also described in https://bugs.debian.org/868059: Sync include/xtables.h from iptables to make sure the right offset is used when accessing structure members defined in libxtables. One could get “Extension does not know id …” otherwise. (See also: #868059) Patch to sync the included xtables.h with system iptables 1.6.x. This continues to work with iptables 1.8.2. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: simplify linking libelf for eBFP/XDP object file supportTony Ambardar2019-02-113-61/+21
| | | | | | | | | | Simplify build and runtime dependencies on libelf, which allows tc and ip to load BPF and XDP object files respectively. Preserve optionality of libelf by having configuration script follow the HAVE_ELF environment variable, used similarly to the HAVE_MNL variable. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: use tc package variant to limit other package sizesTony Ambardar2019-02-111-0/+9
| | | | | | | | | | | | | Replace the old 'tc' with a singleton package variant which will be used to enable additional functionality and limit it only to tc. Non-variant packages will only be installed during 'tiny' variant builds, hence will be configured without extra features, thus preserving previously limited functionality and reduced package sizes. Also set ip-tiny as the default variant, and install 'tiny' versions of development libraries. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: simplify Makefile, patches and fix feature detectionTony Ambardar2019-02-113-20/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | Compile-based feature detection (e.g. xtables, ipset support) was broken due to silent compilation errors in the configure script, caused by a Makefile variable KERNEL_INCLUDE referring to kernel build headers. Use userspace headers by setting the same "user_headers" kernel include path as used for the iptables build. Remove redundant or unused Build/Configure definitions from package Makefile, including KERNEL_INCLUDE, LIBC_INCLUDE and DBM includes. Don't pass LDFLAGS within MAKE_FLAGS as this interferes with LDFLAGS in tc/Makefile and masks a link parameter ("-Wl,-export-dynamic"). Instead, use standard TARGET_LDFLAGS. Replace EXTRA_CCOPTS in MAKE_FLAGS with cleaner TARGET_CPPFLAGS, and also drop now unneeded patch 150-extra-ccopts.patch. Enable defining XT_LIB_DIR from Makefile, needed to set the iptables modules directory to something other than /lib/xtables, and also add libxtables dependency. Both are needed with working xtables detection. Note that libxtables is also pulled in by iptables, firewall or luci, so this change has no size impact in most cases. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* iproute2: fix broken configuration patchTony Ambardar2019-02-112-7/+12
| | | | | | | | | | Since v4.13, iproute2 switched to a config.mk file with greater use of pkg-config for library/feature detection. Replace the old Config patch with one modifying the configure script but enabling the same changes: - explicitly disable TC_CONFIG_ATM - rely on feature detection for IP_CONFIG_SETNS and TC_CONFIG_XT Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* base-files: enable BPF JIT sysctl by defaultTony Ambardar2019-02-111-0/+2
| | | | | | Set net.core.bpf_jit_enable=1 in /etc/sysctl.d/10-default.conf. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: enable CONFIG_BPF_JIT by defaultTony Ambardar2019-02-113-3/+3
| | | | | | | | | | | | | | | | | | Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels, which should speed up cBPF and eBPF-based packet filtering (tc, iptables) and packet sniffing (libpcap, tcpdump, fwknopd, etc). This has minimal kernel size impact, increasing the size of uImage-lzma (normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32 arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14. With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko) running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT. This change aligns with the notion of OpenWRT as the network go-to swiss army knife for packet handling, especially on CPU-constrained platforms. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel/modules: add kmod-bpf-test packageTony Ambardar2019-02-111-0/+11
| | | | | | | | Add the test_bpf module that runs various test vectors against the BPF interpreter or BPF JIT compiler. The module must be manually loaded, as with the kmod-crypto-test module which serves a similar purpose. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel/modules: add kmod-sched-bpf packageTony Ambardar2019-02-111-1/+17
| | | | | | | Add cls_bpf and act_bpf modules for additional tc classifier and action support of cBPF and eBPF. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel/modules: add kmod-sched-ipset packageTony Ambardar2019-02-111-1/+16
| | | | | | | | Add em_ipset module to support tc filter classification by IP set. Build as a standalone package to help avoid pulling in rest of kmod-sched and isolate new dependency on kmod-ipt-ipset. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel/modules: kmod-sched: add some common, useful actionsTony Ambardar2019-02-111-1/+5
| | | | | | | | | | | | | Add act_pedit, act_csum, act_gact and act_simple modules for additional tc action support. Module act_simple helps with debug and logging, similar to iptables LOG target, while act_gact provides common generic actions. Modules act_pedit and act_csum support general packet mangling, and have been the subject of feature requests and forum discussions (e.g. DSCP), as well as being added to the Turris OS fork of OpenWrt ~2 years ago. Also select dependency kmod-lib-crc32c to support act_csum. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel/modules: kmod-sched-core: add missing dependency, useful moduleTony Ambardar2019-02-111-2/+4
| | | | | | | | | | | | | | | | All tc ematch modules, including those in kmod-sched-core and kmod-sched, use cls_basic as a core dependency. Relocate cls_basic from kmod-sched to kmod-sched-core to avoid requiring kmod-sched unnecessarily. This change is also backwards compatible since any past tc ematch users will have had to install both kmod-sched-core and kmod-sched anyway. Add the matchall kernel module cls_matchall introduced in kernel 4.8. The matchall classifier matches every packet and allows the user to apply actions on it. It is a simpler, more efficient replacement for the common but cryptic tc classifier idiom "u32 match u32 0 0". Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-113-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* gemini: Fix kmod-led-trig-heartbeat typoLinus Walleij2019-02-111-1/+1
| | | | | | | | It's kmod-ledtrig-* not kmod-led-trig-*. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [extended subject] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mac80211: ath10k: support for management rate controlSven Eckelmann2019-02-113-1/+156
| | | | | | | | | | | | | Issues a wmi command to firmware when multicast rate change is received with the new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting for CCK rates which got introduced with addition of ath10k_rates_rev2 enum. By default the firmware uses 1Mbps and 6Mbps rate for management packets in 2G and 5G bands respectively. But when the user selects different basic rates from the userspace, we need to send the management packets at the lowest basic rate selected by the user. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath10k-ct: support for management rate controlSven Eckelmann2019-02-113-1/+156
| | | | | | | | | | | | By default the firmware uses 1Mbps and 6Mbps rate for management packets in 2G and 5G bands respectively. But when the user selects different basic rates from the userspace, we need to send the management packets at the lowest basic rate selected by the user. This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the management packets rate to the firmware. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath10k-firmware: update Candela Tech firmware imagesChristian Lamparter2019-02-111-16/+16
| | | | | | | | | | | | | | | | | | Release notes since last time: 2019-02-08: Fix rate-ctrl assert related to bad logic that tried to guess that lower bandwidth probes were automatically successful if higher was. The NSS mismatch that can happen here caused the assert. Just comment out the offending code (per comment from original QCA code). This is bug 69. 2019-02-10: Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67). Original buggy commit was commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* build: add KERNEL_ENTRY and sort DEFAULT_DEVICE_VARSChristian Lamparter2019-02-111-6/+5
| | | | | | | | | | | | | | | | | The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS. This bug was discovered while preparing alternative images for the mpc85xx's TP-Link WDR4900-V1, which all failed to boot due to this: |## Booting kernel from Legacy Image at 02000000 ... | Image Name: POWERPC OpenWrt Linux-4.14.96 | Image Type: PowerPC Linux Kernel Image (uncompressed) | Data Size: 2056568 Bytes = 2 MiB | Load Address: 01000000 | Entry Point: 00000000 | Verifying Checksum ... OK Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mac80211: brcmfmac: fix a possible NULL pointer dereferenceRafał Miłecki2019-02-111-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a possible crash in the brcmf_fw_request_nvram_done(): [ 31.687293] Backtrace: [ 31.689760] [<c004fb4c>] (__wake_up_common) from [<c004fc38>] (__wake_up_locked+0x1c/0x24) [ 31.698043] r10:c6794000 r9:00000009 r8:00000001 r7:bf54dda0 r6:a0000013 r5:c78e7d38 [ 31.705928] r4:c78e7d3c r3:00000000 [ 31.709528] [<c004fc1c>] (__wake_up_locked) from [<c00502a8>] (complete+0x3c/0x4c) [ 31.717148] [<c005026c>] (complete) from [<bf54590c>] (brcmf_fw_request_nvram_done+0x5c8/0x6a4 [brcmfmac]) [ 31.726818] r7:bf54dda0 r6:c6794000 r5:00001990 r4:c6782380 [ 31.732544] [<bf545344>] (brcmf_fw_request_nvram_done [brcmfmac]) from [<c0204e40>] (request_firmware_work_func+0x38/0x60) [ 31.743607] r10:00000008 r9:c6bdd700 r8:00000000 r7:c72c3cd8 r6:c67f4300 r5:c6bda300 [ 31.751493] r4:c67f4300 [ 31.754046] [<c0204e08>] (request_firmware_work_func) from [<c0034458>] (process_one_work+0x1e0/0x318) [ 31.763365] r4:c72c3cc0 [ 31.765913] [<c0034278>] (process_one_work) from [<c0035234>] (worker_thread+0x2f4/0x448) [ 31.774107] r10:00000008 r9:00000000 r8:c6bda314 r7:c72c3cd8 r6:c6bda300 r5:c6bda300 [ 31.781993] r4:c72c3cc0 [ 31.784545] [<c0034f40>] (worker_thread) from [<c003984c>] (kthread+0x100/0x114) [ 31.791949] r10:00000000 r9:00000000 r8:00000000 r7:c0034f40 r6:c72c3cc0 r5:00000000 [ 31.799836] r4:c735dc00 r3:c79ed540 [ 31.803438] [<c003974c>] (kthread) from [<c00097d0>] (ret_from_fork+0x14/0x24) [ 31.810672] r7:00000000 r6:00000000 r5:c003974c r4:c735dc00 [ 31.816378] Code: e5b53004 e1a07001 e1a06002 e243000c (e5934000) [ 31.822487] ---[ end trace a0ffbb07a810d503 ]--- Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: add rssileds for xw devicesKoen Vandeputte2019-02-111-0/+1
| | | | | | | | | | | Commit 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") adds support for using the RSSI strenght via LEDS. The rssileds package addition got lost during altering the patch. Add it again to fix this. Fixes: 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* tools/mpfr: Update to 4.0.2Daniel Engberg2019-02-102-5/+5
| | | | | | | | | Update mpfr to 4.0.2 Use official site as last resort Force thread-safety functionality Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/bison: Update to 3.3.2Daniel Engberg2019-02-102-14/+14
| | | | | | | | Update bison to 3.3.2 Enable pthreads support Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/sed: Update to 4.7Daniel Engberg2019-02-101-2/+3
| | | | | | | Update sed to 4.7 Enable pthreads support Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/tar: Update to 1.31Daniel Engberg2019-02-103-6/+6
| | | | | | | | | Update tar to 1.31 Fixes CVE-2018-20482 Switch to tar.xz tarball Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* glibc: update to latest 2.27 commit [BZ #24180]Hans Dedecker2019-02-091-2/+2
| | | | | | 9f44fa22cb Add compiler barriers around modifications of the robust mutex list for pthread_mutex_trylock. [BZ #24180] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* vti: remove setting default firewall zone to wanHans Dedecker2019-02-092-3/+1
| | | | | | | | | Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set default firewall zone to wan as the firewall zone for the vti interface can be configured in the firewall config or it makes it impossible not to specify a firewall zone for the vti interface. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 11:16:13 +0000