aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: dts: assign the PCI pins to the PCI controller nodeMartin Blumenstingl2019-12-2227-260/+213
| | | | | | | | Assign the PCI pins to the PCI controller node instead of using pin hogging (where pins are assigned to the pin controller). This is the preferred way of assigning pins upstream. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: dts: assign the STP pins to the STP GPIO controller nodeMartin Blumenstingl2019-12-2211-68/+36
| | | | | | | | Assign the STP pins to the STP GPIO controller node instead of using pin hogging (where pins are assigned to the pin controller). This is the preferred way of assigning pins upstream. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: dts: assign the GPHY LED pins to the Ethernet controller nodeMartin Blumenstingl2019-12-227-54/+71
| | | | | | | | Assign the GPHY LED pins to the Ethernet controller node instead of using pin hogging (where pins are assigned to the pin controller). This is the preferred way of assigning pins upstream. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: dts: assign the NAND pins to the nand-controller nodeMartin Blumenstingl2019-12-2216-85/+112
| | | | | | | | | | | | Assign the NAND pins to the NAND controller node instead of using pin hogging (where pins are assigned to the pin controller). This is the preferred way of assigning pins upstream. While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and CE/CS1). This means that the pinctrl subsystem knows that these pins are in use and cannot be re-assigned as GPIOs for example. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: dts: define the SPI pins in {amazonse,ar9,vr9}.dtsiMartin Blumenstingl2019-12-2212-141/+66
| | | | | | | | | Define the SPI pins in the corresponding SoCs.dtsi and assign them to the SPI controller node. All known boards use CS4 and it's likely that this is hardcoded in bootrom so this doesn't bother with having per-board SPI pinmux settings. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: dts: assign the MDIO pins to the gsw nodeMartin Blumenstingl2019-12-2219-80/+27
| | | | | | | | | | | | Assign the MDIO pins to the switch node instead of using pin hogging (where pins are assigned to the pin controller). This is the preferred way of assigning pins upstream. This converts amazonse, ar9 and vr9. danube is skipped because the pin controller doesn't define a pinmux for the MDIO pins (some of the SoC pads may be hardwired to the MDIO pins instead of being configurable). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ramips: further DTS improvements for Edimax RG21SAdrian Schmutzler2019-12-221-8/+6
| | | | | | | | | | This fixes the state_default node by setting the correct groups and inheriting &state_default from parent DTSI directly. The compatible for the wifi nodes is changed to the more generic mediatek,mt76. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add eth0 MAC address for Edimax RG21SAdrian Schmutzler2019-12-222-1/+3
| | | | | | | | | | | | | | | So far, lan/wan MAC address for Edimax RG21S are only read using mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but eth0 address is random. Since the device's LAN address is the same as for 2.4 GHz, though, this patch set's the eth0 address based on the 2.4 GHz one, which can be extracted by mtd-mac-address. This will also allow to move the label MAC address setup to DT. The setup of lan_mac and wan_mac are kept in 02_network, so those locations are still in use, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58USungbo Eo2019-12-222-48/+2
| | | | | | RT-AC58U has single USB 3.0 port, and only usb3_port1 is actually used. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: improve ASUS RT-AC58U supportSungbo Eo2019-12-224-20/+26
| | | | | | | | | | | | | | | | | | | | This patch does the following: - move WiFi LED setup to DTS - fix LAN/WAN MAC addresses and add label MAC address - wan5G -> wlan5G, power -> led_power - increase flash SPI frequency to 30MHz MAC addresses are stored in Factory partition at: 0x1006: WiFi 2.4GHz, WAN (label_mac) 0x5006: WiFi 5GHz, LAN (label_mac +4) By improving flash speed, `time dd if=/dev/mtdblock8 of=/dev/null bs=2k` is reduced from 7m 10.26s to 5m 9.52s. Using higher frequencies did not improve speed further. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: fix MAC address setup for TL-WDR4300 boardSungbo Eo2019-12-212-1/+5
| | | | | | | | | | | | | | | | | The current ethernet MAC address setup of TL-WDR4300 board is different from the setup of stock firmware: OpenWrt: lan = label_mac -2, wan = label_mac -2 stock: lan = label_mac, wan = label_mac +1 This patch applies to all devices using TL-WDR4300 board: TL-WDR3600 v1 TL-WDR4300 v1 TL-WDR4300 v1 (IL) TL-WDR4310 v1 Mercury MW4530R v1 Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: fix MAC address setup for TP-Link TL-WDR3600/TL-WDR4300Sungbo Eo2019-12-212-1/+6
| | | | | | | | | | | | | | | | | | | | | | | The current ethernet MAC address setup of TL-WDR4300 board is different from the setup of stock firmware: OpenWrt: lan = label_mac -2, wan = label_mac -2 stock: lan = label_mac, wan = label_mac +1 The full address assignment is as follows: LAN label WAN label + 1 5G label 2G label - 1 This patch changes all devices using TL-WDR4300 board: TL-WDR3600 v1 (checked on device) TL-WDR4300 v1 (checked on device) TL-WDR4300 v1 (IL) Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rephrase/extend commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Aruba AP-303David Bauer2019-12-209-1/+469
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: WiFi (amber / green) System (red / green) BTN: Reset To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UARt adapter. Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself an adapter cable: VCC - NC D+ - TX D- - RX GND - GND The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: add BDF for Aruba AP-303David Bauer2019-12-202-0/+2
| | | | | | The BDF originates from the vendor-firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix USB LED for Belkin F9K1109v1Sungbo Eo2019-12-201-1/+1
| | | | | | | | | | | | | | Device support for Belkin F9K1109v1 was added using set_usb_led() although this was removed in 772b27c20736 ("ramips: set F5D8235 v1 usb led trigger via devicetree"). Use ucidef_set_led_usbport() instead. Fixes: f2c83532f92c ("ramips: add support for Belkin F9K1109v1") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rephrase commit title and message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* fstools: update to latest git HEADRafał Miłecki2019-12-201-3/+3
| | | | | | | | | | | | 111a43f libblkid-tiny: vfat: Change parsing label in special cases f43a1aa libblkid-tiny: vfat: Fix reading labels which starts with byte 0x05 157924d libblkid-tiny: add blkid_probe_set_id_label() stub 0c5761f libblkid-tiny: use separated buffer for each block device read b82c5c1 libblkid-tiny: add functions for allocating & freeing probe struct 12851d6 blockd: don't flush devices list on "hotplug" call 5ea47fe blockd: fix vlist memory corruption Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* sunxi: rename SUNXI_SOC to SOCAdrian Schmutzler2019-12-204-38/+37
| | | | | | | This replaces SUNXI_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rename MTK_SOC to SOCAdrian Schmutzler2019-12-207-321/+320
| | | | | | | This replaces MTK_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename ATH_SOC to SOCAdrian Schmutzler2019-12-208-174/+173
| | | | | | | This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: image: add SOC device variableAdrian Schmutzler2019-12-201-1/+2
| | | | | | | | | This creates the device variable SOC and adds it to DEFAULT_DEVICE_VARS. It is supposed to replace target-specific SOC variables like ATH_SOC or MTK_SOC and thus unify variable names across targets. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-208-138/+187
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-195-227/+235
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* uci: update to latest Git HEADPetr Štetiar2019-12-191-4/+5
| | | | | | | | | | | 165b44413145 uci: Fix extra semicolons warnings 66264ed9ec9e cmake: add more hardening compiler flags cca6f105fae2 libuci: refactor uci_get_errorstr 750b046eb77f tests: cram: Lua: add test case for uci_get_errorstr 654d7c33da28 lua: add missing forward declaration 03dfbbe6fef7 cli: fix format string clang-10 warning Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-envtools: ath79: fix missing etactica eg200 supportKarl Palsson2019-12-191-0/+1
| | | | | | | | | | Was inadvertantly missed from the inital forward port from ar71xx to ath79. Fixes: 1588114cf2a3 ("ath79: add etactica-eg200 support") Signed-off-by: Karl Palsson <karlp@etactica.com> [commit description/subject facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79-tiny: enable 4k sectorsPaul Fertser2019-12-191-0/+1
| | | | | | | | | | | | | | | | This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs that support it. Writeable jffs2 overlay used to store settings requires a partition with at least 5 erase blocks, so using small sectors is essential for devices with 4MiB flash. Sysupgrading a device running firmware without this feature will likely not allow to preserve configs automatically but since ath79 is considered to be in a "technology preview" state it shouldn't be a problem. Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: add D-Link DIR-615 E4Paul Fertser2019-12-195-0/+203
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - FCC ID: KA2IR615E3 - SoC: MIPS32 24K 400 MHz Atheros AR7240 - RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T - Flash: 4 MiB NOR SPI Macronix MX25L3208E - Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors - Ethernet: 5x 100BASE-TX Fast Ethernet - LEDs: 9x GPIO, 1x ath9k - Buttons: 2x tactile switches - UART: 3.3 V, 115200 8n1 - USB: simple hardware modification required, 1x USB 1.1 Full Speed Partitioning notes: Vendor firmware (based on CameoAP99) defines two additional partitions: "mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000. The "mac" partition stores LAN MAC address and hardware board name. However, the vendor firmware uses addresses from "nvram" partition, and the board name is used only for informational purposes in the Web interface (included in the pages' header), not affecting the firmware image check. The "lp" partition is supposed to contain a "language pack" (which can be used to add an additional language support to the Web interface) and is flashed separately, using the vendor firmware upgrade page. Since these partitions are absolutely useless for OpenWrt and overwriting them doesn't prevent downgrading to obsolete vendor firmware, this patch appends the valueable space to "firmware". Installation instructions: - Upgrade from OpenWrt ar71xx with "sysupgrade -f -n" or - Upload as a firmware update via the vendor Web-interface or - Connect UART and use "loady" to upload and run OpenWrt initramfs image, then sysupgrade from it (TFTP client doesn't work) or - Before powering up hold "reset" button and keep it pressed for about 15 seconds after, then access fail safe Web server on 192.168.0.1 (the old uIP TCP/IP protocol stack is not compatible with modern Linux, the kernel, so you'll need to use some other OS to do this). Can be performed without a Web-browser too: curl http://192.168.0.1/cgi/index \ -F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: enable all space on Netgear ar9344-based WNDR routersMichal Cieslakiewicz2019-12-191-5/+20
| | | | | | | | | | | Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash memory but only first 32 MiB are used now - both by vendor's firmware and OpenWrt. This patch concatenates two regions of flash memory: ubi part of firmware partition and reserved (unused) space beyond 'caldata_backup' while preserving ART backup. No data is wiped or moved away. This increases area for OS ubi volumes from 23 to 119 Megabytes. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* base-files: send informational UDP message each second waitingPaul Fertser2019-12-191-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The preinit network initialisation and failsafe informational message are inherently racy as the interface takes some time to become functional after "ip link set $pi_ifname up" command. Consider this timing: [ 12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready [ 12.118877] random: procd: uninitialized urandom read (4 bytes read) [ 13.068614] eth1: link up (1000Mbps/Full duplex) [ 13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready Since the UDP message was sent prior to link becoming ready, it was never seen on the wire. The default failsafe timeout is set to 2 seconds, so with this patch there are two attempts to send the message, one spent in vain, and the other visible in tcpdump on an attached host. Of course, in cases when the interface is brought up faster it leads to two messages, however it should be harmless. This patch (almost) doesn't affect normal boot time while still allowing to enter failsafe reliably with a single button press, matching the official "generic failsafe" documentation. Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* iputils: move iputils tools to packages feedPetr Štetiar2019-12-197-510/+0
| | | | | | | | | iputils has moved from the master tree to the packages feed, and is switching from the abandoned skbuff.net upstream to github.com/iputils/iputils. Ref: https://git.openwrt.org/556698cedf9e86a0ffe9f148d4e8e733676c26f6 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: switch to 4.19 kernel versionAnsuel Smith2019-12-191-1/+1
| | | | | | | | | | | | It has been used by several people for some time already and feedback has been mostly positive. Ref: https://github.com/openwrt/openwrt/pull/2472 Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800] Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817] Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [separate commit, commit subject and description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: update USB3 modules for 4.19Ansuel Smith2019-12-191-1/+1
| | | | | | | | | - Use new dwc3-qcom usb driver. - Drop dwc3-of-simple as we have a dedicated driver now. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [split into separate commit, commit subject facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: add missing core1 voltage tolerancePavel Kubelun2019-12-191-0/+1
| | | | | | | | Voltage tolerance is accounted per core, not per cpu, so add missing DT entry. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: make dwc3 usb driver depends on kernel 4.14Ansuel Smith2019-12-191-2/+2
| | | | | | | - usb-dwc3-of-simple is not used anymore as we have qcom dedicated driver - usb-phy-qcom-dwc3 is not dependent of dwc3-of-simple Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix tsens driver in 4.19Ansuel Smith2019-12-191-0/+20
| | | | | | | | | | | | | | | | | | | Added patch: - 063-3 Fix tsense shared memory problem Recent changes in ioremap_resource function are causing fails for the memory areas which are already mapped. This changes are causing tsense driver failures during initialization: qcom-tsens 900000.thermal-sensor: tsens init failed So this patch uses simple ioremap in order to use this shared memory space. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [commit subject and desciption facelitf] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: improve mdio gpios listChristian Lamparter2019-12-199-9/+18
| | | | | | | | | Improve rediability of gpio mdio list. No functional change. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: ap161: fix wrong definition stdoutChristian Lamparter2019-12-191-1/+1
| | | | | | | | | | | From documentation https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt should be just stdout-path Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: ap148: reorganize dtsChristian Lamparter2019-12-191-161/+155
| | | | | | | Reorganize dts to use tags from ipq8064 dtsi Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: d7800: fix warning on dtc compilationChristian Lamparter2019-12-191-2/+3
| | | | | | | | There is warning with "property has invalid length (4 bytes)" related to nand definition. Set size-cells to zero to fix this. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: r7800: add missing wifi definition for pcieChristian Lamparter2019-12-191-0/+30
| | | | | | | Add missing wifi compatible definition for r7800 device. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: use ipq8064 dedicated watchdogChristian Lamparter2019-12-191-1/+2
| | | | | | | Add missing watchdog to list of compatible timers Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: add nand and sata tagsChristian Lamparter2019-12-191-2/+2
| | | | | | | | Add some tags for nand and sata structure to easily reference them in other dts. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: increase drive-strength for pinmuxChristian Lamparter2019-12-191-3/+3
| | | | | | | | | | | | | | | Increase drive-strength from https://lore.kernel.org/patchwork/patch/626885/ 2mA drive strength is not enough when we connect multiple i2c devices on the bus with different pull up resistors. This issue was detected when multiple i2c devices connected on the other side of level shifters on Linaro sensor board. Maxing up to 16mA made i2c much stable. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: add missing gpio and gsbi declarationChristian Lamparter2019-12-191-0/+51
| | | | | | | Adds missing gpio and gsbi declaration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: disable spc on ipq8065 socAnsuel Smith2019-12-191-0/+8
| | | | | | | Spc is disabled in ipq8065 board as it does cause cpu lockup (probably caused by wrong register being set) Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: set apq8064 regulator to support cpuidleAnsuel Smith2019-12-191-2/+3
| | | | | | Set qcom,apq8064-saw2-v1.1-cpu as regulator to make cpuidle work. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: convert ipq8064 dtsi interruptsChristian Lamparter2019-12-191-27/+33
| | | | | | | | | | | | | Convert hardcoded interrupts value to types defined in gci include file. Interrupts sets to 0 are converted to IRQ_TYPE_LEVEL_HIGH to fix kernel warning. Same fix has been applied to arm64 dts. https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1797143 https://patchwork.kernel.org/patch/10367453/ https://patchwork.kernel.org/patch/10315315/ Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: use new usb3 implementationChristian Lamparter2019-12-1916-290/+64
| | | | | | | | | Use new usb3 implementation and refresh dts to the new dwc3 structure Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: fix missing compatible and renameChristian Lamparter2019-12-192-2/+2
| | | | | | | | | | - ipq8064 compatible was missing from nbg6817. - Rename ap148 with a better descriptive name. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: convert ok to okay in dtsChristian Lamparter2019-12-1912-184/+184
| | | | | | | DT spec require okay instead of ok in dts files Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: refresh 4.19 patchesChristian Lamparter2019-12-1948-12445/+1092
| | | | | | | | | | | | | | | | | | | | | | | | | | Reworked: - 0034 patchset update Added: - 080 Add support for pinctrl-msm framework Removed: - 0074-ipq806x-usb-Control-USB-master-reset.patch (we now have a dedicated driver for qcom usb) - 0047-mtd-nand-Create-a-BBT-flag-to-access-bad-block-marke (merged upstream) - 310-msm-adhoc-bus-support (it looks like it was never actually used in any dts) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [commit subject and description facelift, SoB fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 15:19:28 +0000