aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* archs38: use generic 02_sysinfoAdrian Schmutzler2020-07-223-51/+2
| | | | | | | | | | | | | | | | | Currently archs38 sets a board name from compatible for no apparent reason. Just use the compatible directly instead. This theoretically removes a board name "generic" when no compatible was present, however, there is no case where this "generic" board name was actually used. This also fixes an issue where snps,axs103 would not have been properly detected anyway, as its case was not set up syntactically correct. Fixes: 73015c4cb378 ("linux: add support of Synopsys ARCHS38-based boards") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: switch MT7620 subtarget to 5.4David Bauer2020-07-221-0/+2
| | | | | | | | | MT7620 seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Tested on Archer C2 v1 / Archer C20i Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: increase SPI frequency for MT7620 ArcherDavid Bauer2020-07-223-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Increase the SPI frequency for the MT7620 based TP-Link Archer series to 30MHz. TP-Link uses different SPI flash chips for the same board revision, so be conservative to not break boards with a different chip. 30MHz should be well supported by all chips. Tested on Archer C2 v1 (GD25Q64B) and Archer C20i (W25Q64FV). Archer C20i (before) ==================== root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k 122+0 records in 122+0 records out real 0m 15.30s user 0m 0.00s sys 0m 15.29s Archer C20i (after) =================== root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k 122+0 records in 122+0 records out real 0m 5.99s user 0m 0.00s sys 0m 5.98s Signed-off-by: David Bauer <mail@david-bauer.net> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: re-enable image generation for GL-AR750SDavid Bauer2020-07-224-33/+23
| | | | | | | | | | | | | | | | The bootloader only writes the first 2MB of the image to the NOR flash when installing the NAND factory image. The bootloader is capable of booting larger kernels as it boots from the memory mapped SPI flash. Disable the NAND factory image. The NAND can be bootstrapped by writing the NAND initramfs image using the NOR upgrade method in the bootloader web-recovery and sysupgrading from there. The NOR variant is not affected. Also refactor the partition definitions in the DTS to make them less annoying to read. Signed-off-by: David Bauer <mail@david-bauer.net>
* kmod-sched-cake-oot: fix PKG_MIRROR_HASHKevin Darbyshire-Bryant2020-07-221-1/+1
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* umdns: fix compiling using gcc 10Kevin Darbyshire-Bryant2020-07-221-3/+3
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* glibc: fix memcpy and memmove for negative length [BZ #25620]Hans Dedecker2020-07-211-2/+2
| | | | | | | | 6f3459f985 Add NEWS entry for CVE-2020-6096 (bug 25620) 64246fccaf arm: CVE-2020-6096: Fix multiarch memcpy for negative length [BZ #25620] 9bbd2b6172 arm: CVE-2020-6096: fix memcpy and memmove for negative length [BZ #25620] Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: correctly define WiFi switch for TL-WR841ND v8Adrian Schmutzler2020-07-214-34/+51
| | | | | | | | | | | | | | | | | | | | | | | | The TL-WR841ND v8 feature a WiFi switch instead of a button. This adds the corresponding input-type to prevent booting into failsafe regularly. This has been defined correctly in ar71xx, but was overlooked when migrating to ath79. In contrast, the TL-WR842ND v2, which has the key set up as switch in ar71xx, actually has a button. The TL-MR3420 v2 has a button as well and is set up correctly for both targets. (Information based on TP-Link user guide) Note: While looking into this, I found that support PR for TL-MR3420 v2 switched reset button to ACTIVE_HIGH. However, the other two device still use ACTIVE_LOW. This seems strange, but I cannot verify it lacking the affected devices. Fixes: FS#2733 Fixes: 9601d94138de ("add support for TP-Link TL-WR841N/ND v8") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: improve LED support for D-Link DIR-615 D seriesAdrian Schmutzler2020-07-212-5/+8
| | | | | | | | | | | | | This patch adds a trigger for the WAN LED and enhances support for the WiFi LED by enabling activity indication. This is based on bug report feedback (see reference below). While at it, update the LED node names in DTS file. Fixes: FS#732 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* omap: derive DEVICE_DTS from device nameAdrian Schmutzler2020-07-211-3/+1
| | | | | | | | In most cases the DEVICE_DTS name can be derived easily from the node name, so let's do this to enforce harmonized names where possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* apm821xx: derive DEVICE_DTS from device nameAdrian Schmutzler2020-07-213-6/+1
| | | | | | | | | | | The DEVICE_DTS variable always matches the device definition name, just with "_" replaced by "-". Thus, create a DEVICE_DTS definition in Device/Default and drop all the individual statements. If necessary in the future, local DEVICE_DTS will still overwrite that default. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm47xx: fix switch setup for Linksys WRT610N v2Adrian Schmutzler2020-07-211-0/+1
| | | | | | | | | | | | WRT610N V2 is not detected by the initial network configuration script. The switch remains unconfigured and wlan/lan vlans are not created. This adds the correct setup for the device. Fixes: FS#1869 Suggested-by: Alessandro Radicati Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: fix indentAdrian Schmutzler2020-07-211-2/+2
| | | | | | Fix indent to be consistent with the rest of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix network setup for Ubiquiti ER-X/ER-X-SFPNelson Cai2020-07-201-2/+2
| | | | | | | | | | | | The function name ucidef_set_interface_lan_wan does not exist, use the proper name by adding an "s" and thereby fix network setup on these devices. Fixes: 22468cc40c8b (ramips: erx and erx-sfp: fix missing WAN interface) Signed-off-by: Nelson Cai <niphor@gmail.com> [commit message/title facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* hostapd: enter DFS state if no available channel is foundDavid Bauer2020-07-201-0/+37
| | | | | | | | | | | Previously hostapd would not stop transmitting when a DFS event was detected and no available channel to switch to was available. Disable and re-enable the interface to enter DFS state. This way, TX does not happen until the kernel notifies hostapd about the NOP expiring. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: create channel list for fixed channel operationDavid Bauer2020-07-201-0/+3
| | | | | | | | | | | | Currently a device which has a DFS channel selected using the UCI channel setting might switch to a non-DFS channel in case no chanlist is provided (UCI setting "channels") when the radio detects a DFS event. Automatically add a chanlist consisting of the configured channel when the device does not operate in auto-channel mode and no chanlist set to circumvent this issue. Signed-off-by: David Bauer <mail@david-bauer.net>
* vxlan: add capability for multiple fdb entriesJohannes Kimmel2020-07-202-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Similar to wireguard, vxlan can configure multiple peers or add specific entries to the fdb for a single mac address. While you can still use peeraddr/peer6addr option within the proto vxlan/vxlan6 section to not break existing configurations, this patch allows to add multiple sections that conigure fdb entries via the bridge command. As such, the bridge command is now a dependency of the vxlan package. (To be honest without the bridge command available, vxlan isn't very much fun to use or debug at all) Field names are taken direclty from the bridge command. Example with all supported parameters, since this hasn't been documented so far: config interface 'vx0' option proto 'vxlan6' # use vxlan over ipv6 # main options option ip6addr '2001:db8::1' # listen address option tunlink 'wan6' # optional if listen address given option peer6addr '2001:db8::2' # now optional option port '8472' # this is the standard port under linux option vid '42' # VXLAN Network Identifier to use option mtu '1430' # vxlan6 has 70 bytes overhead # extra options option rxcsum '0' # allow receiving packets without checksum option txcsum '0' # send packets without checksum option ttl '16' # specifies the TTL value for outgoing packets option tos '0' # specifies the TOS value for outgoing packets option macaddr '11:22:33:44:55:66' # optional, manually specify mac # default is a random address Single peer with head-end replication. Corresponds to the following call to bridge: $ bridge fdb append 00:00:00:00:00:00 dev vx0 dst 2001:db8::3 config vxlan_peer option vxlan 'vx0' option dst '2001:db8::3' # always required For multiple peers, this section can be repeated for each dst address. It's possible to specify a multicast address as destination. Useful when multicast routing is available or within one lan segment: config vxlan_peer option vxlan 'vx0' option dst 'ff02::1337' # multicast group to join. # all bum traffic will be send there option via 'eth1' # for multicast, an outgoing interface needs # to be specified All available peer options for completeness: config vxlan_peer option vxlan 'vx0' # the interface to configure option lladdr 'aa:bb:cc:dd:ee:ff' # specific mac, option dst '2001:db8::4' # connected to this peer option via 'eth0.1' # use this interface only option port '4789' # use different port for this peer option vni '23' # override vni for this peer option src_vni '123' # see man 3 bridge Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
* vxlan: remove mandatory peeraddrJohannes Kimmel2020-07-201-12/+0
| | | | | | | | | | vxlan can be configured without a peer address. This is used to prepare an interface and add peers later. Fixes: FS#2743 Signed-off-by: Johannes Kimmel <fff@bareminimum.eu> Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
* tplink-safeloader: expand support list for TP-Link CPE210 v3Adrian Schmutzler2020-07-201-1/+8
| | | | | | | | | | | | | | This adds new strings to the support list for the TP-Link CPE210 v3 that are supposed to work with the existing setup. Without it, the factory image won't be accepted by the vendor UI on these newer revisions. Tested on a CPE210 v3.20 (EU). Ref: https://forum.openwrt.org/t/build-for-cpe210-v3-20/68000 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* dnsmasq: bump to 2.82Kevin Darbyshire-Bryant2020-07-202-13/+13
| | | | | | | | | This fixes a nasty problem introduced in 2.81 which causes random crashes on systems where there's significant DNS activity over TCP. It also fixes DNSSEC validation problems with zero-TTL DNSKEY and DS records. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* procd: bump to git HEAD once againDaniel Golle2020-07-201-3/+3
| | | | | | | | | | | Further complete OCI container support in ujail: f5f305e jail: move /tmp/resolv.conf.d to /dev/resolv.conf.d 6f078ae jail: add support for defining devices 686cf7a jail: actually apply filesystem-specific mount options f91009a jail: refactor default mounts into new structure 66ae2d9 jail: re-implement /proc/sys/net read-write in netns hack Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lantiq/xrx200: make WLAN button responsive on Fritzbox 7360 & 7362Dustin Gathmann2020-07-202-2/+2
| | | | | | | | | | | | | Pressing the 'WLAN' button should enable/disable wireless activity. Currently, the button is mapped to the KEY_WLAN, which will not have this effect. This patch changes the mapping of the WLAN button, so a button press will emit an action for the 'rfkill' key instead of 'wlan'. Apparently, this is what stock OpenWRT expects. This fix is analogous to the preceding patch for Fritzbox 3370. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* lantiq/xrx200: fix WLAN button actions for Fritzbox 3370Dustin Gathmann2020-07-202-2/+2
| | | | | | | | | | | | The WLAN button actions are reversed, i.e. pressing the button emits a 'released' action, and vice versa. This can easily be checked by adding logger -t button_action "$BUTTON $ACTION" as the second line of /etc/rc.button/rfkill, and using logread to read the events (assuming the preceding patch has been applied). Defining the GPIO as ACTIVE_LOW corrects this behavior. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* lantiq/xrx200: make WLAN button responsive on Fritzbox 3370Dustin Gathmann2020-07-202-2/+2
| | | | | | | | | | | Pressing the 'WLAN' button should enable/disable wireless activity. However, on the Fritzbox 3370 this doesn't have an effect. This patch changes the mapping of the physical WLAN button, so a button press will emit an action for the 'rfkill' key instead of 'wlan'. Apparently, this is what stock OpenWRT expects, and also what is implemented for most other devices. Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
* procd: update to git HEADDaniel Golle2020-07-191-3/+3
| | | | | | | | | | | 9eddf0f jail: fix hooks 1b1286b jail: parse and apply OCI sysctl values c049047 jail: implement OCI user additionalGIDs 0e1920c jail: read and apply umask from OCI if defined 1c46cc3 jail: parse and apply POSIX rlimits 76adac5 jail: /proc/$pid/oom_score_adj to OCI defined oomScoreAdj Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix flash layout for TP-Link TL-WR841N v14Alexander Müller2020-07-192-2/+8
| | | | | | | | | | | | | | | | The config partition was missing from the flash layout of the device. Although the stock firmware resets a corrupted config partition to the default values, the TFTP flash with an image bigger than 0x3d0000 will truncate the image as the bootloader only copies 0x3d0000 bytes to flash during TFTP flashing. Fixed by adding the config partition and shrinking the firmware partition. Fixes: 3fd97c522bb7 ("ramips: add support for TP-Link TL-WR841n v14") Signed-off-by: Alexander Müller <donothingloop@gmail.com>
* ramips: remove incorrect mtd-eeprom for TP-Link TL-WR841N v14Adrian Schmutzler2020-07-191-1/+1
| | | | | | | | | | | | | | | | | The factory partition on this device is only 64k in size, so having mediatek,mtd-eeprom = <&factory 0x10000> would place the EEPROM data after the end of the flash. As can be verified against the TP-Link GPL sources, which contain the EEPROM data as binary blob, the actual address for the EEPROM data is 0x0. Since 0x0 is default for MT7628, the incorrect line is just removed. This error is the reason for the abysmal Wifi performance that people are complaining about for the WR841Nv14. Fixes: 3fd97c522bb7 ("ramips: add support for TP-Link TL-WR841n v14") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: don't create switch config for VIXMINIDavid Bauer2020-07-181-5/+2
| | | | | | | | | Don't create UCI switch config for the GL.iNet microuter-N300 and VIXMINI. These devices only have a single LAN port. Creating the switch config makes usage of VLANs more complicated, as they would have to be configured on the MAC as well as the "switch". Signed-off-by: David Bauer <mail@david-bauer.net>
* procd: bump to git HEADDaniel Golle2020-07-171-4/+4
| | | | | | | | | | 8d5208f jail: fix false return in case of nofail mount b41f76b procd: fix compile if procd-ujail is not selected 86a5105 jail: fs: fix build on uClibc-ng bfce7d1 jail: fix some more mount options 268126a jail: add support for maskedPaths and readonlyPaths Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lantiq: move 01_led_migration script to subtargetsAdrian Schmutzler2020-07-173-7/+61
| | | | | | | | | | | | Split the /etc/uci-defaults/01_led_migration scripts into subtargets as already done for most of the other base-files. While this introduces a minor amount of code duplication, it still is considered an improvement, as device-specific settings are kept together in the subtargets' base-files and the script at hand can be removed entirely for two of the subtargets not needing it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ltq-*dsl-app: dsl_control: remove unneeded check for lantiq_dsl.shMartin Schiller2020-07-174-4/+4
| | | | | | | | | | This file is always present because it is part of the ltq-dsl-base package on which these packages depend. This check would not have been necessary in the past, because the script was part of the TARGET_LANTIQ on which these packages also depend. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* lantiq: move dsl related base-files into own packageMartin Schiller2020-07-177-2/+34
| | | | | | | | | | It does not make sense to install this components on lantiq systems where the dsl subsystem is not needed/used. This also makes it possible to use the files also on other targets. (hopefully ipq401x / FritzBox 7530 in the near future) Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
* ramips: move redundant console setup to mt7621 SoC DTSIAdrian Schmutzler2020-07-1747-181/+4
| | | | | | | | | | | | | | | | | For mt7621, console is set up via DTS bootargs individually in device DTS/DTSI files. However, 44 of 74 statements use the following setting: chosen { bootargs = "console=ttyS0,57600"; }; Therefore, don't repeat ourselves and move that definition to the SoC DTSI file to serve as a default value. This patch is cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.52John Audia2020-07-1725-135/+105
| | | | | | | | | update_kernel.sh refreshed all patches, no human interaction was needed Build system: x86_64 Run-tested: Netgear R7800 (ipq806x) Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: add arl_table support for MT7530Salvatore Mesoraca2020-07-171-0/+119
| | | | | | | Use switch.h API to expose MT7530's ARL table to user space. Signed-off-by: Salvatore Mesoraca <salvatore@samknows.com>
* lzo: fix pkgconfig pathsRosen Penev2020-07-171-1/+3
| | | | | | | | | The last commit to this package that added the pkgconfig file did not fix the paths to point to the prefix. This allows packages to find lzo properly. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu: add Kobol Helios 4 deviceAlberto Bursi2020-07-179-0/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Helios 4 is a NAS from Kobol that is powered by an Armada 38x MicroSOM from Solidrun, similarly to Clearfog. This device has: -Armada 38x CPU (dual core ARMv7 1.6 Ghz) -2 GB of ECC RAM -Gigabit ethernet (Marvell) -2x USB 3.0 ports -4x Sata 3.0 ports -i2c header (J9 |>GND|SDA|SCL|VCC) -2x 3-pin fan headers with PWM -micro-usb port is a TTL/UART to USB converter connected to TTL -MicroSD card slot -System, 4xSata and 1xUSB LEDs NOT WORKING: fan control Fan Control requires a kernel patch that is available in the Armbian project (the "default firmware" of this device) and named mvebu-gpio-remove-hardcoded -timer-assignment This patch isn't acceptable by OpenWrt, it should be upstreamed. I also have that patch in my own local OpenWrt builds, in case you want a more clean and less confusing patch for upstreaming. To install, write the disk image on a micro SD card with dd or win32 disk imager, insert the card in the slot. Check that the dip switch battery for boot selection is as follows Switch 1 and 2 down/off, switches 3, 4, 5 up/on. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* uboot-mvebu: add uboot for helios 4Alberto Bursi2020-07-171-0/+8
| | | | | | add u-boot for Helios 4 NAS Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* nat46: update to latest git HEADHans Dedecker2020-07-161-3/+3
| | | | | | ac712ad nat46-netdev: Add support for removing a rule Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: add support for D-Link DIR-867/DIR-882 A1Mateus B. Cassiano2020-07-166-152/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v1Santiago Rodriguez-Papa2020-07-1610-159/+239
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Everything works! Been running it for a couple weeks now and haven't had any problems. Please let me know if you run into any. Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev> [use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide common definition for ELECOM WRC GS devicesAdrian Schmutzler2020-07-167-35/+24
| | | | | | | | | | | | | | Add a common definition for ELECOM WRC "GS" devices to mt7621.mk to not repeat the same assignments five times. To keep the naming consistent, slightly rename the DTSI and the factory image recipe as well. Note that elecom_wrc-1167ghbk2-s uses a slightly different build recipe for the factory image, so we keep it separate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
* ramips: add support for ELECOM WRC-1750GS/GSVINAGAKI Hiroshi2020-07-163-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. WRC-1750GSV has the same hardware with WRC-1750GS. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-1750GS (or WRC-1750GSV) normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button for WRC-1750GS : wrc-1750gs-squashfs-factory.bin for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin 4. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: backport latest pci/e driver from upstreamJohn Crispin2020-07-167-24/+1932
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: generate UBI images for the rev boardJohn Crispin2020-07-163-2/+48
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: minor fix to eip97 driverJohn Crispin2020-07-161-2/+2
| | | | | | This patch makes the driver work on the newer v2.3 core. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: harmonize model names for Ubiquiti devicesAdrian Schmutzler2020-07-1517-27/+26
| | | | | | | | | | | | | | | | | | | | This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* base-files: replace backticks in lib/upgrade/nand.shAdrian Schmutzler2020-07-151-4/+4
| | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* package: drop PKG_VERSION for purely local packagesAdrian Schmutzler2020-07-1515-22/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the package guidelines, PKG_VERSION is supposed to be used as "The upstream version number that we're downloading", while PKG_RELEASE is referred to as "The version of this package Makefile". Thus, the variables in a strict interpretation provide a clear distinction between "their" (upstream) version in PKG_VERSION and "our" (local OpenWrt trunk) version in PKG_RELEASE. For local (OpenWrt-only) packages, this implies that those will only need PKG_RELEASE defined, while PKG_VERSION does not apply following a strict interpretation. While the majority of "our" packages actually follow that scheme, there are also some that mix both variables or have one of them defined but keep them at "1". This is misleading and confusing, which can be observed by the fact that there typically either one of the variables is never bumped or the choice of the variable to increase depends on the person doing the change. Consequently, this patch aims at clarifying the situation by consistently using only PKG_RELEASE for "our" packages. To achieve that, PKG_VERSION is removed there, bumping PKG_RELEASE where necessary to ensure the resulting package version string is bigger than before. During adjustment, one has to make sure that the new resulting composite package version will not be considered "older" than the previous one. A useful tool for evaluating that is 'opkg compare-versions'. In principle, there are the following cases: 1. Sole PKG_VERSION replaced by sole PKG_RELEASE: In this case, the resulting version string does not change, it's just the value of the variable put in the file. Consequently, we do not bump the number in these cases so nobody is tempted to install the same package again. 2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE: In this case, the resulting version string has been "version-release", e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just need to be higher than the previous PKG_VERSION. For the cases where PKG_VERSION has always sticked to "1", and PKG_RELEASE has been incremented, we take the most recent value of PKG_RELEASE. Apart from that, a few packages appear to have developed their own complex versioning scheme, e.g. using x.y.z number for PKG_VERSION _and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION (adb-enablemodem, wwan). I didn't touch these few in this patch. Cc: Hans Dedecker <dedeckeh@gmail.com> Cc: Felix Fietkau <nbd@nbd.name> Cc: Andre Valentin <avalentin@marcant.net> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Steven Barth <steven@midlink.org> Cc: Daniel Golle <dgolle@allnet.de> Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* vxlan: bump and change to PKG_RELEASEAdrian Schmutzler2020-07-151-1/+1
| | | | | | | | | | | | | Bumping package version has been overlooked in a previous commit. While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter is meant for upstream version number only. (The effective version string for the package would be "3" in both cases, so there is no harm done for version comparison.) Fixes: 0453c3866feb ("vxlan: fix udp checksum control") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 23:25:27 +0000