aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix WLI-TX4-AG300N boot and networkYo Abe2017-01-131-2/+11
| | | | | | | | | | | | | | | | Partition label "linux" prevents the root file system to be mounted at boot time leading to a kernel panic. After changing it to "firmware", the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data" are correctly recognized. The attached IP175C 10/100 MBit switch cannot connect to a link with fixed 1000Mbit speed. The correct link speed is 100MBit. The switch is detected and can be configured via mdio bus and should allow two separable VLANs to be configured for the 4 available ports. Signed-off-by: Yo Abe <abe.geel@gmail.com> [picked from openwrt/PR#330] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for VoCore2Andrew Yong2017-01-137-0/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ar71xx: enable serial console on Mikrotik RB411/RB433David Varga2017-01-131-1/+3
| | | | | | | | | This patch adds support for serial console on Mikrotik RB411 and RB433 series devices. Signed-off-by: David Varga <duvi@duvinet.hu> [picked from FS#377] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: rt3883: fix typo in pinctrl lna_g_funcDaniel Golle2017-01-131-0/+26
| | | | | | | | Spotted by forum users https://forum.openwrt.org/viewtopic.php?pid=347439#p347439 Reported-by: Tom Psyborg <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* map: take over maintainershipHans Dedecker2017-01-121-1/+1
| | | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Acked-by: Jo-Philipp Wich <jo@mein.io>
* odhcp6c: take over maintainershipHans Dedecker2017-01-121-1/+1
| | | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Acked-by: Jo-Philipp Wich <jo@mein.io>
* odhcpd: take over maintainershipHans Dedecker2017-01-121-1/+1
| | | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Acked-by: Jo-Philipp Wich <jo@mein.io>
* Revert "dnsmasq: change 'add_local_hostname' to use dnsmasq '--interface-name'"Hans Dedecker2017-01-122-31/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This causes problem when a FQDN is configured in /etc/config/system. The domain name will appear twice in reverse DNS. Next to that, there seems to be a bug in dnsmasq. From the manual page: --interface-name=<name>,<interface>[/4|/6] Return a DNS record associating the name with the primary address on the given interface. This flag specifies an A or AAAA record for the given name in the same way as an /etc/hosts line, except that the address is not constant, but taken from the given interface. The interface may be followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses of the interface should be used. If the interface is down, not configured or non-existent, an empty record is returned. The matching PTR record is also created, mapping the interface address to the name. More than one name may be associated with an interface address by repeating the flag; in that case the first instance is used for the reverse address-to-name mapping. It does not just create an A/AAAA record for the primary address, it creates one for all addresses. And what is worse, it seems to actually resolve to the non-primary address first. This is quite annoying when you use floating IP addresses (e.g. VRRP), because when the floating IP is on the other device, SSH failes due to incorrect entry in the known hosts file. I know that this is not a common setup, but it would be nice if there was an option to restore the previous behaviour, rather than just forcing this new feature on everybody. Reported-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* map: delete map-t device when tearing down map interfaceHans Dedecker2017-01-122-2/+12
| | | | | | | | | | | | Delete the map-t device when tearing down the map-t interface; as such there's no conflict when the map-t interface comes up again when trying to add the map-t device as the map-t device was still present (Can not add: device 'map-wan6_4' already exists!). Only call ifdown in teardown for map-e and lw6o4 map interfaces types in order to suppress the trace "wan6_4 (6652): Interface wan6_4_ not found" Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Revert the recent dependency and metadata scanning reworkFelix Fietkau2017-01-114-4/+4
| | | | | | | | | | | | | | | This reverts the following commits: fbe522d1204149b6c128d55e360bfc15fa8258e1 278ad007ee03c4455c3507322e34b0e3e6ec050d 863888e44f7a1fb1675a2e7a2eaabfec3561d2a2 96daf6352f6e04bc22789466cb5409b93fbec191 cfd83555fc4f0bab18a26f6812da18e64df46ff3 This seems to trigger some mconf bugs when built with all feeds packages, so I will try to find a less intrusive solution before the release. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* comgt: allow build without USB_SUPPORTFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* umbim: allow build without USB_SUPPORTFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uqmi: allow build without USB_SUPPORTFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mountd: allow build without USB_SUPPORTFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scripts/package-metadata.pl: fix overriding conditional dependencies with ↵Felix Fietkau2017-01-111-0/+2
| | | | | | | | | | | conditional select Conditional dependencies use the '(!cond) || dep' syntax, whereas conditional select uses 'dep if cond'. Add an extra check to suppress emitting a conditional if an equal conditional select already exists. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* arc770: build dtb files in Image/Prepare so that they are available for Device/*Felix Fietkau2017-01-111-5/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* archs38: build dtb files in Image/Prepare so that they are available for ↵Felix Fietkau2017-01-111-5/+7
| | | | | | Device/* Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: backport upstream bcm53xx spi driver changesRafał Miłecki2017-01-113-41/+102
| | | | | | | One replaces our local patch and another is just for keeping driver in sync (license change). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: work around an ethernet tx scheduling fairness issueFelix Fietkau2017-01-111-0/+36
| | | | | | | | | | | The hardware queue scheduling is apparently configured with fixed priorities, which creates a nasty fairness issue where traffic from one CPU can starve traffic from all other CPUs. Work around this issue by forcing all tx packets to go through one CPU, until this issue is fixed properly. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: only add UBI EOF markers for devices that need itFelix Fietkau2017-01-111-1/+2
| | | | | | Fixes issues where the second-stage u-boot already uses UBI. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* procd: add support for overriding the tar sysupgrade board nameFelix Fietkau2017-01-111-1/+10
| | | | | | Useful for providing images that work for multiple devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: disable sub-page writes on routerboard nand driversFelix Fietkau2017-01-113-0/+3
| | | | | | They seem to fail in tests using UBI, and are not used by yaffs2 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove linux 4.1 supportFelix Fietkau2017-01-11187-31552/+0
| | | | | | | The only target still referencing it is omap24xx, and it is marked as broken. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix legacy image build errorFelix Fietkau2017-01-111-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* arc770: fix parallel build issueFelix Fietkau2017-01-111-7/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* archs38: fix parallel build issueFelix Fietkau2017-01-111-7/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix RB4xx CPLD SPI device mode setupFelix Fietkau2017-01-111-1/+1
| | | | | | | | Commit af79fdbe4af3 changed the code to use tx_nbits for dual SPI tx transfers, however the SPI stack only allows this when the device mode includes the relevant bit as well Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix RB4xx SPI driver mode bitsFelix Fietkau2017-01-111-1/+1
| | | | | | Accept SPI_TX_DUAL in device mode to fix the CPLD driver Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: update mwlwifi driver to version 10.3.2.0-20170110Kabuli Chana2017-01-111-3/+3
| | | | | | | | | | Improves automatic channel section support. Tested on AC (mamba) and ACM (rango). Signed-off-by: Kabuli Chana <newtownBuild@gmail.com> [Jo-Philipp Wich: reword commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: backport a MIPS SMP icache flush fixFelix Fietkau2017-01-111-0/+38
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update bcm47xxpart failsafe partition patchesRafał Miłecki2017-01-115-37/+49
| | | | | | V2 using helper function was sent for upstream kernel Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* wpa_supplicant: Fix mesh encryption configSujith Manoharan2017-01-111-1/+4
| | | | | | | | | | | | | | | wpa_supplicant allows only SAE as the key management type for mesh mode. The recent key_mgmt rework unconditionally added WPA-PSK - this breaks interface bringup and wpa_s throws this error message: Line 10: key_mgmt for mesh network should be open or SAE Line 10: failed to parse network block. Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf Fix this by making sure that only SAE is used for mesh. Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
* gettext-full: avoid using iconv for host buildsJo-Philipp Wich2017-01-111-1/+4
| | | | | | | | | | | The gettext-full host build might pick up iconv-stub host build headers during the build, leading to stray linker errors with unresolved references to libiconv_open(), libiconv() and libiconv_close(). Since we're not needing iconv support on the host, pass the appropriate cache variables to configure to prevent detection and linking of iconv. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: cmake: link librt if needed (FS#381)Jo-Philipp Wich2017-01-112-3/+33
| | | | | | | | | | Patch cmakes cmcurl component to unconditionally link librt when we discover a clock_gettime() symbol in -lrt. This is required to sucessfully link LibreSSL's libcrypto which might or might not reqauire librt. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: mkimage: pass crypto libraries through HOST_LOADLIBES (FS#381)Jo-Philipp Wich2017-01-111-2/+2
| | | | | | | | Since linker argument order is significant on modern host compilers, pass the required libcrypto libraries through the HOST_LOADLIBES variable in order to ensure proper order of the final linker command line. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: libressl: always build as PICMatthias Schiffer2017-01-101-0/+1
| | | | | | | | | Fixes link errors for host packages like ruby like the following: /usr/bin/ld: .../staging_dir/host/lib/libcrypto.a(libcrypto_la-md5_dgst.o): relocation R_X86_64_PC32 against symbol `memcpy@@GLIBC_2.14' can not be used when making a shared object; recompile with -fPIC Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* package: replace $(STAGING_DIR)/host with $(STAGING_DIR_HOSTPKG)Matthias Schiffer2017-01-108-22/+22
| | | | | | | | | Cleanup to prepare for changing STAGING_DIR_HOSTPKG. The actual change of STAGING_DIR_HOSTPKG (i.e., moving the host packages back into a common, not target-specific directory) will be done after the first LEDE release, but the cleanup will also be useful for projects like Gluon. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: add missing config symbolsJo-Philipp Wich2017-01-101-0/+2
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: add missing config symbolFelix Fietkau2017-01-101-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: pending brcmfmac patches cleaning channels managementRafał Miłecki2017-01-106-2/+257
| | | | | | They prepare brcmfmac for using wiphy_read_of_freq_limits. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mac80211: rename b43 patches to make more spaceRafał Miłecki2017-01-106-0/+0
| | | | | | Just 6 patches were using 80*, 81*, 82* and 84* prefixes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: scan.mk: consider KernelPackage pattern as wellJo-Philipp Wich2017-01-101-1/+1
| | | | | | | | The removal of the ".+Package" pattern in scan.mk also caused the build system to skip over Makefiles defining only kmods. Adjust the grep pattern to consider packages with "call KernelPackage" signatures as well. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* procd: update mirror hashJohn Crispin2017-01-101-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* kernel: remove gpiommc patches / driverFelix Fietkau2017-01-109-2874/+0
| | | | | | | This code was marked as incompatible to Linux 4.4 well over a year ago and nobody cared, and now it's breaking builds. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add pending bcm47xxpart support for failsafe TRX partitionRafał Miłecki2017-01-105-52/+316
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: update spi-nor.h include fix with upstream accepted versionRafał Miłecki2017-01-101-2/+3
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: rename bcm47xxpart patches to fit more of themRafał Miłecki2017-01-102-0/+0
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: scan.mk: remove overlay broad grep patternJo-Philipp Wich2017-01-101-1/+1
| | | | | | | | | | | | | | | | | Commit af0b91c "allow scan.mk to find python packages introduced in [8639]" added some special casing to scan.mk to accomodate some nonstandard python packages. Nowadays this pattern is not needed anymore and produces false positives when using the LEDE source repository as feed within the SDK since the metadata scanning wrongly picks up target/imagebuilder/Makefile as package, leading to an "ERROR: please fix feeds/base/target/imagebuilder/Makefile" message. Remove the now uneeded pattern to fix such stray errors during metadata scanning. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: remove DEVTMPFS platform overridesFelix Fietkau2017-01-104-5/+0
| | | | | | Those options are handled via top-level menuconfig instead Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove DEVMEM/DEVKMEM platform overridesFelix Fietkau2017-01-107-7/+0
| | | | | | Those options are handled via top-level menuconfig instead Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 21:48:56 +0000