diff options
Diffstat (limited to 'target/linux/generic/backport-5.4/790-net-phy-at803x-select-correct-page-on-config-init.patch')
-rw-r--r-- | target/linux/generic/backport-5.4/790-net-phy-at803x-select-correct-page-on-config-init.patch | 104 |
1 files changed, 0 insertions, 104 deletions
diff --git a/target/linux/generic/backport-5.4/790-net-phy-at803x-select-correct-page-on-config-init.patch b/target/linux/generic/backport-5.4/790-net-phy-at803x-select-correct-page-on-config-init.patch deleted file mode 100644 index b7e3201fb7..0000000000 --- a/target/linux/generic/backport-5.4/790-net-phy-at803x-select-correct-page-on-config-init.patch +++ /dev/null @@ -1,104 +0,0 @@ -From c329e5afb42ff0a88285eb4d8a391a18793e4777 Mon Sep 17 00:00:00 2001 -From: David Bauer <mail@david-bauer.net> -Date: Thu, 15 Apr 2021 03:26:50 +0200 -Subject: [PATCH] net: phy: at803x: select correct page on config init - -The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber -as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit -in the chip configure register. - -The driver assumes the copper side is selected on probe, but this might -not be the case depending which page was last selected by the -bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior. - -Select the copper page when probing to circumvent this. - -Signed-off-by: David Bauer <mail@david-bauer.net> -Signed-off-by: David S. Miller <davem@davemloft.net> ---- - drivers/net/phy/at803x.c | 50 +++++++++++++++++++++++++++++++++++++++- - 1 file changed, 49 insertions(+), 1 deletion(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -67,6 +67,9 @@ - #define ATH8035_PHY_ID 0x004dd072 - #define AT803X_PHY_ID_MASK 0xffffffef - -+#define AT803X_PAGE_FIBER 0 -+#define AT803X_PAGE_COPPER 1 -+ - MODULE_DESCRIPTION("Atheros 803x PHY driver"); - MODULE_AUTHOR("Matus Ujhelyi"); - MODULE_LICENSE("GPL"); -@@ -112,6 +115,35 @@ static int at803x_debug_reg_mask(struct - return phy_write(phydev, AT803X_DEBUG_DATA, val); - } - -+static int at803x_write_page(struct phy_device *phydev, int page) -+{ -+ int mask; -+ int set; -+ -+ if (page == AT803X_PAGE_COPPER) { -+ set = AT803X_BT_BX_REG_SEL; -+ mask = 0; -+ } else { -+ set = 0; -+ mask = AT803X_BT_BX_REG_SEL; -+ } -+ -+ return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); -+} -+ -+static int at803x_read_page(struct phy_device *phydev) -+{ -+ int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); -+ -+ if (ccr < 0) -+ return ccr; -+ -+ if (ccr & AT803X_BT_BX_REG_SEL) -+ return AT803X_PAGE_COPPER; -+ -+ return AT803X_PAGE_FIBER; -+} -+ - static int at803x_enable_rx_delay(struct phy_device *phydev) - { - return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, -@@ -244,6 +276,7 @@ static int at803x_probe(struct phy_devic - { - struct device *dev = &phydev->mdio.dev; - struct at803x_priv *priv; -+ int ret = 0; - - priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); - if (!priv) -@@ -251,7 +284,16 @@ static int at803x_probe(struct phy_devic - - phydev->priv = priv; - -- return 0; -+ /* Some bootloaders leave the fiber page selected. -+ * Switch to the copper page, as otherwise we read -+ * the PHY capabilities from the fiber side. -+ */ -+ if ((phydev->phy_id & phydev->drv->phy_id_mask) == (ATH8031_PHY_ID & phydev->drv->phy_id_mask)) { -+ ret = phy_select_page(phydev, AT803X_PAGE_COPPER); -+ ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); -+ } -+ -+ return ret; - } - - static int at803x_config_init(struct phy_device *phydev) -@@ -466,6 +508,8 @@ static struct phy_driver at803x_driver[] - .get_wol = at803x_get_wol, - .suspend = at803x_suspend, - .resume = at803x_resume, -+ .read_page = at803x_read_page, -+ .write_page = at803x_write_page, - /* PHY_GBIT_FEATURES */ - .read_status = at803x_read_status, - .aneg_done = at803x_aneg_done, |