diff options
Diffstat (limited to 'target/linux/ath79')
| -rw-r--r-- | target/linux/ath79/dts/qca9558_linksys_ea4500-v3.dts | 211 | ||||
| -rw-r--r-- | target/linux/ath79/image/nand.mk | 19 | ||||
| -rw-r--r-- | target/linux/ath79/nand/base-files/etc/board.d/02_network | 4 | ||||
| -rwxr-xr-x | target/linux/ath79/nand/base-files/etc/init.d/bootcount | 4 |
4 files changed, 238 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/qca9558_linksys_ea4500-v3.dts b/target/linux/ath79/dts/qca9558_linksys_ea4500-v3.dts new file mode 100644 index 0000000000..000dbce8e1 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_linksys_ea4500-v3.dts @@ -0,0 +1,211 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + compatible = "linksys,ea4500-v3", "qca,qca9558"; + model = "Linksys EA4500 v3"; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + label-mac-device = ð1; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "green:system"; + gpios = <&gpio 21 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "pci168c,0033"; + reg = <0x0000 0 0 0 0>; + nvmem-cells = <&cal_ath9k_pci>; + nvmem-cell-names = "calibration"; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x100000 0x40000>; + }; + + partition@140000 { + label = "caldata"; + reg = <0x140000 0x40000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + cal_macaddr: macaddr@0 { + reg = <0x6 0x6>; + }; + + cal_ath9k_soc: cal_ath9k@1000 { + reg = <0x1000 0x440>; + }; + + cal_ath9k_pci: cal_ath9k@5000 { + reg = <0x5000 0x440>; + }; + }; + + partition@180000 { + label = "s_env"; + reg = <0x180000 0x40000>; + read-only; + }; + + partition@1c0000 { + label = "devinfo"; + reg = <0x1c0000 0x100000>; + read-only; + }; + + partition@2c0000 { + label = "firmware"; + reg = <0x2c0000 0x5000000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x4c00000>; + }; + + /* Original layout for secondary partitions */ + /* partition@2800000 { + label = "kernel2"; + reg = <0x2800000 0x400000>; + }; + + partition@2c00000 { + label = "ubi2"; + reg = <0x2c00000 0x2400000>; + }; */ + }; + + partition@52c0000 { + label = "syscfg"; + reg = <0x52c0000 0x2d40000>; + read-only; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x07600000 /* PORT0 PAD MODE CTRL: RGMII, to eth0 */ + 0x0c 0x00000080 /* PORT6 PAD MODE CTRL: SGMII, to eth1 */ + 0x50 0xc833c833 /* LED_CTRL0: orange, blinking with act */ + 0x54 0xcf85cf85 /* LED_CTRL1: green, on with link */ + 0x58 0x00000000 /* LED_CTRL2: unpopulated */ + 0x5c 0x00f3cf00 /* LED_CTRL3: enable led 0 and 1 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6 STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + nvmem-cells = <&cal_macaddr>; + nvmem-cell-names = "mac-address"; + phy-handle = <&phy0>; + pll-data = <0x96000000 0x00000101 0x00001616>; + + gmac-config { + device = <&gmac>; + rgmii-enabled = <1>; + }; +}; + +ð1 { + status = "okay"; + + nvmem-cells = <&cal_macaddr>; + nvmem-cell-names = "mac-address"; + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&cal_ath9k_soc>; + nvmem-cell-names = "calibration"; +}; diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk index 1d086b1918..1bf7227017 100644 --- a/target/linux/ath79/image/nand.mk +++ b/target/linux/ath79/image/nand.mk @@ -211,6 +211,25 @@ define Device/glinet_gl-xe300 endef TARGET_DEVICES += glinet_gl-xe300 +define Device/linksys_ea4500-v3 + SOC := qca9558 + DEVICE_VENDOR := Linksys + DEVICE_MODEL := EA4500 + DEVICE_VARIANT := v3 + DEVICE_PACKAGES := kmod-usb2 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 81920k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + LINKSYS_HWNAME := EA4500V3 + IMAGES += factory.img + IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \ + append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME) + UBINIZE_OPTS := -E 5 +endef +TARGET_DEVICES += linksys_ea4500-v3 + # fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff) define Device/netgear_ath79_nand DEVICE_VENDOR := NETGEAR diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network index b533e5be6c..3c5627e2a4 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network @@ -30,6 +30,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "4:lan" ;; + linksys,ea4500-v3) + ucidef_add_switch "switch0" \ + "6@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0" + ;; netgear,r6100) ucidef_set_interface_wan "eth1" ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/nand/base-files/etc/init.d/bootcount b/target/linux/ath79/nand/base-files/etc/init.d/bootcount index 87654ba095..4d7a814f05 100755 --- a/target/linux/ath79/nand/base-files/etc/init.d/bootcount +++ b/target/linux/ath79/nand/base-files/etc/init.d/bootcount @@ -8,5 +8,9 @@ boot() { glinet,gl-ar300m-nand) fw_setenv bootcount 0 ;; + linksys,ea4500-v3) + [ $(fw_printenv -n auto_recovery) = yes ] && \ + fw_setenv auto_recovery no + ;; esac } |