diff options
| -rw-r--r-- | package/firmware/ipq-wifi/Makefile | 2 | ||||
| -rw-r--r-- | package/firmware/ipq-wifi/board-engenius_emd1.qca4019 | bin | 0 -> 24316 bytes | |||
| -rwxr-xr-x | target/linux/ipq40xx/base-files/etc/board.d/02_network | 5 | ||||
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 8 | ||||
| -rw-r--r-- | target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts | 233 | ||||
| -rw-r--r-- | target/linux/ipq40xx/image/Makefile | 13 | ||||
| -rw-r--r-- | target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch | 3 |
7 files changed, 263 insertions, 1 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 065cda160d..eada8baf6f 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -28,6 +28,7 @@ ALLWIFIBOARDS:= \ aruba_ap-303 \ avm_fritzrepeater-1200 \ dlink_dap2610 \ + engenius_emd1 \ ezviz_cs-w3-wd1200g-eup \ linksys_ea8300 \ qxwlan_e2600ac @@ -96,6 +97,7 @@ endef $(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303)) $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200)) $(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610)) +$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) diff --git a/package/firmware/ipq-wifi/board-engenius_emd1.qca4019 b/package/firmware/ipq-wifi/board-engenius_emd1.qca4019 Binary files differnew file mode 100644 index 0000000000..3a2d77597d --- /dev/null +++ b/package/firmware/ipq-wifi/board-engenius_emd1.qca4019 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 9cfc43f1f9..4b636fc701 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -49,6 +49,7 @@ ipq40xx_setup_interfaces() avm,fritzrepeater-1200|\ dlink,dap-2610 |\ engenius,eap1300|\ + engenius,emd1|\ meraki,mr33|\ netgear,ex6100v2|\ netgear,ex6150v2|\ @@ -108,6 +109,10 @@ ipq40xx_setup_macs() lan_mac=$(mtd_get_mac_ascii bdcfg lanmac) label_mac=$lan_mac ;; + engenius,emd1) + lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) + label_mac=$lan_mac + ;; engenius,ens620ext) wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) lan_mac=$(macaddr_add "$wan_mac" 1) diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 22ac6eefc5..957bee12ab 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -91,6 +91,10 @@ case "$FIRMWARE" in caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac) ;; + engenius,emd1) + caldata_extract "0:ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) + ;; engenius,ens620ext) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) @@ -166,6 +170,10 @@ case "$FIRMWARE" in caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a) ;; + engenius,emd1) + caldata_extract "0:ART" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1) + ;; engenius,ens620ext) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts new file mode 100644 index 0000000000..cf4f793f21 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-emd1.dts @@ -0,0 +1,233 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "EnGenius EMD1"; + compatible = "engenius,emd1"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x20>; + switch_wan_bmp = <0x00>; + }; + + edma@c080000 { + status = "okay"; + qcom,num_gmac = <1>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "emd1:white:power"; + gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "emd1:red:wlan2g"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "emd1:blue:wlan5g"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + + mesh { + label = "emd1:orange:mesh"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio54", "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + pin_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition0@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition1@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + partition2@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + partition3@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + partition4@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + partition5@e0000 { + label = "0:APPSBLENV"; + reg = <0x000e0000 0x00010000>; + read-only; + }; + partition6@f0000 { + label = "0:APPSBL"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + partition7@170000 { + label = "0:ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + partition8@180000 { + label = "userconfig"; + reg = <0x00180000 0x00080000>; + read-only; + }; + partition9@200000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x200000 0x01e00000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x20>; +}; + +&cryptobam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "EnGenius-EMD1"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "EnGenius-EMD1"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 41a65280c3..bbe4df9df4 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -278,6 +278,19 @@ define Device/engenius_eap1300 endef TARGET_DEVICES += engenius_eap1300 +define Device/engenius_emd1 + $(call Device/FitImage) + DEVICE_VENDOR := EnGenius + DEVICE_MODEL := EMD1 + DEVICE_DTS_CONFIG := config@4 + SOC := qcom-ipq4018 + IMAGE_SIZE := 30720k + IMAGES := sysupgrade.bin factory.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += engenius_emd1 + define Device/engenius_ens620ext $(call Device/FitImage) DEVICE_VENDOR := EnGenius diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 9c9a31e436..11e775a5dc 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,41 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -20,6 +20,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4018-cs-w3-wd1200g-eup.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ ++ qcom-ipq4018-emd1.dtb \ + qcom-ipq4018-ens620ext.dtb \ + qcom-ipq4018-ex6100v2.dtb \ + qcom-ipq4018-ex6150v2.dtb \ |