aboutsummaryrefslogtreecommitdiffstats
path: root/target
diff options
context:
space:
mode:
authorStijn Tintel <stijn@linux-ipv6.be>2021-11-01 23:39:48 +0200
committerStijn Tintel <stijn@linux-ipv6.be>2022-07-01 12:56:56 +0300
commite9f9cd14cc71826957877999fd063dd080de4751 (patch)
treeacd64bb70227ff770114188f17f844c892920a47 /target
parenta5526efde0c4a5c0a94fc2e7f6bcecd844148408 (diff)
downloadupstream-e9f9cd14cc71826957877999fd063dd080de4751.tar.gz
upstream-e9f9cd14cc71826957877999fd063dd080de4751.tar.bz2
upstream-e9f9cd14cc71826957877999fd063dd080de4751.zip
bcm27xx: add support for Raspberry Pi Zero 2
Due to licensing uncertainty, we do not include the firmwares for the wireless chips used in the Raspberry Pi Zero 2 W. To have working wireless, follow the instructions below. For people building their own images: mkdir -p files/lib/firmware/brcm wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.txt wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.txt Now build the OpenWrt image as usual, and it will include the firmware files in the correct location. For people using ext4 images: Write the ext4 image to the sdcard, then mount the 2nd partition and put the firmware files from the links above in /lib/firmware/brcm relative from the mount point where the partition is mounted. For people using squashfs images: Write the squashfs image to the sdcard, place it in the Raspberry Pi Zero 2 W, boot it and wait for the overlay filesystem to be created. Find the offset of the overlay filesystem in sysfs: # cat /sys/devices/virtual/block/loop0/loop/offset 25755648 Shut down the device, unplug the power and move the SD card to a Linux computer. Mount the 2nd partition of the sdcard as a loop device with the offset found earlier. sudo mount /dev/sdh2 -o loop,offset=25755648 /mnt/temp Put the firmware files from the links above in /upper/lib/firmware/brcm relative to the mount point where the loop device is mounted. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Peter van Dijk <peter@7bits.nl>
Diffstat (limited to 'target')
-rw-r--r--target/linux/bcm27xx/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/bcm27xx/base-files/etc/diag.sh1
-rw-r--r--target/linux/bcm27xx/image/Makefile16
3 files changed, 12 insertions, 6 deletions
diff --git a/target/linux/bcm27xx/base-files/etc/board.d/02_network b/target/linux/bcm27xx/base-files/etc/board.d/02_network
index b4394f6922..23bc9afdb9 100644
--- a/target/linux/bcm27xx/base-files/etc/board.d/02_network
+++ b/target/linux/bcm27xx/base-files/etc/board.d/02_network
@@ -23,6 +23,7 @@ raspberrypi,model-b-rev2)
ucidef_set_interface_lan "eth0"
;;
+raspberrypi,model-zero-2 |\
raspberrypi,model-zero-w)
ucidef_set_interface_lan "wlan0"
;;
diff --git a/target/linux/bcm27xx/base-files/etc/diag.sh b/target/linux/bcm27xx/base-files/etc/diag.sh
index a22ffd3f2a..180b31ec95 100644
--- a/target/linux/bcm27xx/base-files/etc/diag.sh
+++ b/target/linux/bcm27xx/base-files/etc/diag.sh
@@ -20,6 +20,7 @@ set_state() {
raspberrypi,3-compute-module |\
raspberrypi,model-b |\
raspberrypi,model-zero |\
+ raspberrypi,model-zero-2 |\
raspberrypi,model-zero-w)
status_led="led0"
;;
diff --git a/target/linux/bcm27xx/image/Makefile b/target/linux/bcm27xx/image/Makefile
index 83d255f326..4cd1052941 100644
--- a/target/linux/bcm27xx/image/Makefile
+++ b/target/linux/bcm27xx/image/Makefile
@@ -96,13 +96,15 @@ define Device/rpi-2
bcm2709-rpi-2-b bcm2710-rpi-2-b \
bcm2710-rpi-3-b bcm2710-rpi-3-b-plus \
bcm2711-rpi-4-b bcm2711-rpi-400 \
- bcm2710-rpi-cm3 bcm2711-rpi-cm4
+ bcm2710-rpi-cm3 bcm2711-rpi-cm4 \
+ bcm2710-rpi-zero-2
SUPPORTED_DEVICES := \
- rpi-2-b rpi-3-b rpi-3-b-plus rpi-cm \
+ rpi-2-b rpi-3-b rpi-3-b-plus rpi-cm rpi-zero-2 \
raspberrypi,2-model-b raspberrypi,2-model-b-rev2 \
raspberrypi,3-model-b raspberrypi,3-model-b-plus \
raspberrypi,3-compute-module raspberrypi,compute-module-3 \
- raspberrypi,400 raspberrypi,4-compute-module raspberrypi,4-model-b
+ raspberrypi,400 raspberrypi,4-compute-module raspberrypi,4-model-b \
+ raspberrypi,model-zero-2
DEVICE_PACKAGES := \
cypress-firmware-43430-sdio \
cypress-nvram-43430-sdio-rpi-3b \
@@ -126,12 +128,14 @@ define Device/rpi-3
DEVICE_DTS := \
broadcom/bcm2710-rpi-2-b \
broadcom/bcm2710-rpi-3-b broadcom/bcm2710-rpi-3-b-plus \
- broadcom/bcm2710-rpi-cm3
+ broadcom/bcm2710-rpi-cm3 \
+ broadcom/bcm2710-rpi-zero-2
SUPPORTED_DEVICES := \
- rpi-3-b rpi-3-b-plus \
+ rpi-3-b rpi-3-b-plus rpi-zero-2 \
raspberrypi,2-model-b-rev2 \
raspberrypi,3-model-b raspberrypi,3-model-b-plus \
- raspberrypi,3-compute-module raspberrypi,compute-module-3
+ raspberrypi,3-compute-module raspberrypi,compute-module-3 \
+ raspberrypi,model-zero-2
DEVICE_PACKAGES := \
cypress-firmware-43430-sdio \
cypress-nvram-43430-sdio-rpi-3b \