ipq40xx: Add ZTE MF289F

It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).

Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.

There are currently two hardware revisions, which
differ on the 5Ghz radio:

AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz

Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
	(QCA9984): a/n/ac, 4x4 HW REV AT1
	(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot

Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
   in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
   GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
   (refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:

setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr

5. Please make backup of original partitions, if you think about revert to
   stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:

WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin

ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin

6. Login via ssh or serial and remove stock partitions
   (default IP 192.168.0.1):

 # this can return an error, if ubi was attached before
 # or rootfs part was erased before.
ubiattach -m 17

 # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
 # some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data

7. download and install image via sysupgrade -n
 (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
 to the device's /tmp directory)

 sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin

Sometimes it could print ubi attach error, but please ignore it
if process goes forward.

Flash Layout

NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"

SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"

Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
   for the device on a TFTP in the server's root.
   This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
   connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:

This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize

This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize

After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router

Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 0de6a3339f1aadc1de2c9371435e3de239a00645)

[Backported to 22.03: added DTS to the makefile patch, fixed ipq-wifi
inclusion for MF286D]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>

6 files changed, 466 insertions, 7 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 2aa4886e6a..deb9ec64f6 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -150,6 +150,11 @@ ipq40xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "0u@eth1" "5:wan"
 		;;
+	zte,mf289f)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "0u@eth1" "2:lan:1" "5:lan:2"
+		;;
 	*)
 		echo "Unsupported hardware. Network interfaces not initialized"
 		;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
index a52a33d2f4..b5c96da962 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
@@ -24,7 +24,8 @@ mikrotik,cap-ac)
 mikrotik,hap-ac3)
 	ucidef_add_gpio_switch "poe_passtrough" "PoE Passthrough" "452" "0"
 	;;
-zte,mf286d)
+zte,mf286d|\
+zte,mf289f)
 	ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0"
 	;;
 esac
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index e8c94409a7..e9c17e5b01 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -25,7 +25,8 @@ Once this is done. Retry.
 EOF
 		return 1
 		;;
-	zte,mf286d)
+	zte,mf286d |\
+	zte,mf289f)
 		CI_UBIPART="rootfs"
 		local mtdnum="$( find_mtd_index $CI_UBIPART )"
 		[ ! "$mtdnum" ] && return 1
@@ -185,7 +186,8 @@ platform_do_upgrade() {
 		platform_do_upgrade_dualboot_datachk "$1"
 		;;
 	teltonika,rutx10 |\
-	zte,mf286d)
+	zte,mf286d |\
+	zte,mf289f)
 		CI_UBIPART="rootfs"
 		nand_do_upgrade "$1"
 		;;
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts
new file mode 100644
index 0000000000..2dac307990
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
+// Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "ZTE MF289F";
+	compatible = "zte,mf289f";
+
+	aliases {
+		led-boot = &led_status;
+		led-failsafe = &led_status;
+		led-running = &led_status;
+		led-upgrade = &led_status;
+	};
+
+	chosen {
+		/*
+		 * bootargs forced by u-boot bootipq command:
+		 * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
+		 */
+		bootargs-append = " root=/dev/ubiblock0_1";
+	};
+
+	/*
+	 * This node is used to restart modem module to avoid anomalous
+	 * behaviours on initial communication.
+	 */
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status: led-0 {
+			label = "blue:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+		};
+
+		key-wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			/* select hostmode */
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+			status = "okay";
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+};
+
+&prng {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <2000>;
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>,
+		   <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "0:SBL1";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "0:MIBIB";
+				reg = <0x40000 0x20000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "0:QSEE";
+				reg = <0x60000 0x60000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "0:CDT";
+				reg = <0xc0000 0x10000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0xd0000 0x10000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0xe0000 0x10000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "0:APPSBL";
+				reg = <0xf0000 0xc0000>;
+				read-only;
+			};
+
+			partition@1b0000 {
+				label = "0:reserved1";
+				reg = <0x1b0000 0x50000>;
+				read-only;
+			};
+		};
+	};
+
+	spi-nand@1 { /* flash@1 ? */
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "fota-flag";
+				reg = <0x0 0xa0000>;
+				read-only;
+			};
+
+			partition@a0000 {
+				label = "ART";
+				reg = <0xa0000 0x80000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
+			};
+
+			partition@120000 {
+				label = "mac";
+				reg = <0x120000 0x80000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				macaddr_mac_0: macaddr@0 {
+					reg = <0x0 0x6>;
+				};
+			};
+
+			partition@1a0000 {
+				label = "reserved2";
+				reg = <0x1a0000 0xc0000>;
+				read-only;
+			};
+
+			partition@260000 {
+				label = "cfg-param";
+				reg = <0x260000 0x400000>;
+				read-only;
+			};
+
+			partition@660000 {
+				label = "log";
+				reg = <0x660000 0x400000>;
+			};
+
+			partition@a60000 {
+				label = "oops";
+				reg = <0xa60000 0xa0000>;
+			};
+
+			partition@b00000 {
+				label = "reserved3";
+				reg = <0xb00000 0x500000>;
+				read-only;
+			};
+
+			partition@1000000 {
+				label = "web";
+				reg = <0x1000000 0x800000>;
+			};
+
+			partition@1800000 {
+				label = "rootfs";
+				reg = <0x1800000 0x1d00000>;
+			};
+
+			partition@3500000 {
+				label = "data";
+				reg = <0x3500000 0x1900000>;
+			};
+
+			partition@4e00000 {
+				label = "fota";
+				reg = <0x4e00000 0x3200000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac0 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&macaddr_mac_0>;
+};
+
+&gmac1 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&macaddr_mac_0>;
+	mac-address-increment = <1>;
+};
+
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	i2c_0_pins: i2c_0_pinmux {
+		mux {
+			pins = "gpio20", "gpio21";
+			function = "blsp_i2c0";
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio6";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio7";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12", "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration", "mac-address";
+	nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
+	mac-address-increment = <2>;
+	qcom,ath10k-calibration-variant = "zte,mf289f";
+};
+
+/* This node is used only on AT2 version for 5Ghz on IPQ4019 with board-id=21 */
+&wifi1 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration", "mac-address";
+	nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
+	mac-address-increment = <3>;
+	qcom,ath10k-calibration-variant = "zte,mf289f";
+};
+
+/* This node is used only on AT1 version for 5Ghz on QCA9984 */
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>;
+	clkreq-gpio = <&tlmm 39 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi2: wifi@1,0 {
+			nvmem-cell-names = "mac-address";
+			nvmem-cells = <&macaddr_mac_0>;
+			mac-address-increment = <4>;
+			compatible = "qcom,ath10k";
+			reg = <0x00010000 0 0 0 0>;
+			qcom,ath10k-calibration-variant = "zte,mf289f";
+		};
+	};
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index cf89409b17..e02527e108 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -994,19 +994,31 @@ define Device/unielec_u4019-32m
 endef
 TARGET_DEVICES += unielec_u4019-32m
 
-define Device/zte_mf286d
+define Device/zte_mf28x_common
 	$(call Device/FitzImage)
 	DEVICE_VENDOR := ZTE
-	DEVICE_MODEL := MF286D
 	SOC := qcom-ipq4019
 	DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
 	BLOCKSIZE := 128k
 	PAGESIZE := 2048
 	KERNEL_IN_UBI := 1
-	DEVICE_PACKAGES := ipq-wifi-zte_mf286d kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
+	DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
+endef
+
+define Device/zte_mf286d
+	$(call Device/zte_mf28x_common)
+	DEVICE_MODEL := MF286D
+	DEVICE_PACKAGES := ipq-wifi-zte_mf286d
 endef
 TARGET_DEVICES += zte_mf286d
 
+define Device/zte_mf289f
+	$(call Device/zte_mf28x_common)
+	DEVICE_MODEL := MF289F
+	DEVICE_PACKAGES += ipq-wifi-zte_mf289f ath10k-firmware-qca9984-ct
+endef
+TARGET_DEVICES += zte_mf289f
+
 define Device/zyxel_nbg6617
 	$(call Device/FitImageLzma)
 	DEVICE_VENDOR := ZyXEL
diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
index 4fc0566c73..c51586a232 100644
--- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -904,11 +904,75 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -904,11 +904,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -61,6 +61,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-lhgg-60ad.dtb \
 +	qcom-ipq4019-mf286d.dtb \
++	qcom-ipq4019-mf289f.dtb \
 +	qcom-ipq4019-mr8300.dtb \
 +	qcom-ipq4019-pa2200.dtb \
 +	qcom-ipq4019-r619ac-64m.dtb \