filogic: add support for GL.iNet GL-MT6000

Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>

6 files changed, 345 insertions, 0 deletions

diff --git a/target/linux/mediatek/dts/mt7986a-glinet-gl-mt6000.dts b/target/linux/mediatek/dts/mt7986a-glinet-gl-mt6000.dts
new file mode 100644
index 00000000000..2be1907f632
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7986a-glinet-gl-mt6000.dts
@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "GL.iNet GL-MT6000";
+	compatible = "glinet,gl-mt6000", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " root=PARTLABEL=rootfs rootwait";
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_run: led@0 {
+			label = "blue:run";
+			gpios = <&pio 38 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led@1 {
+			label = "white:system";
+			gpios = <&pio 37 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpios = <&pio 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		phy-handle = <&phy1>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy1: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c45";
+			reg = <1>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+			reset-gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&pio>;
+			interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+			realtek,aldps-enable;
+		};
+
+		phy7: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c45";
+			reg = <7>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+			reset-gpios = <&pio 19 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&pio>;
+			interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+			realtek,aldps-enable;
+		};
+
+		switch: switch@31 {
+			compatible = "mediatek,mt7531";
+			reg = <31>;
+			reset-gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&pio>;
+			interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan2";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan3";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan4";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan5";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan1";
+					phy-handle = <&phy7>;
+					phy-mode = "2500base-x";
+				};
+
+				port@6 {
+					reg = <6>;
+					ethernet = <&gmac0>;
+					phy-mode = "2500base-x";
+
+					fixed-link {
+						speed = <2500>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pio {
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&usb_vbus>;
+	status = "okay";
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 42490cf8b3a..590c1fb2a66 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -48,6 +48,7 @@ mediatek_setup_interfaces()
 	qihoo,360t7)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
 		;;
+	glinet,gl-mt6000|\
 	tplink,tl-xdr4288|\
 	tplink,tl-xdr6088)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1
@@ -90,6 +91,11 @@ mediatek_setup_macs()
 		wan_mac=$(macaddr_add "$lan_mac" 3)
 		label_mac=$lan_mac
 		;;
+	glinet,gl-mt6000)
+		label_mac=$(mmc_get_mac_binary factory 0x0a)
+		wan_mac=$label_mac
+		lan_mac=$(macaddr_add "$label_mac" 2)
+		;;
 	h3c,magic-nx30-pro)
 		wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
index f6f18272cc3..e4d33879c6d 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
@@ -36,6 +36,13 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+"mediatek/mt7986_eeprom_mt7976_dual.bin")
+	case "$board" in
+	glinet,gl-mt6000)
+		caldata_extract_mmc "factory" 0x0 0x1000
+		;;
+	esac
+	;;
 *)
 	exit 1
 	;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 0fc90bd41b1..115ff2201ec 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -43,6 +43,11 @@ case "$board" in
 		[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
 		;;
+	glinet,gl-mt6000)
+		addr=$(mmc_get_mac_binary factory 0x04)
+		[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
+		[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
+		;;
 	h3c,magic-nx30-pro)
 		addr=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
 		[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 6155ddab726..42156aefb4d 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -84,6 +84,11 @@ platform_do_upgrade() {
 	cudy,wr3000-v1)
 		default_do_upgrade "$1"
 		;;
+	glinet,gl-mt6000)
+		CI_KERNPART="kernel"
+		CI_ROOTPART="rootfs"
+		emmc_do_upgrade "$1"
+		;;
 	mercusys,mr90x-v1)
 		CI_UBIPART="ubi0"
 		nand_do_upgrade "$1"
@@ -150,6 +155,7 @@ platform_copy_config() {
 			;;
 		esac
 		;;
+	glinet,gl-mt6000|\
 	ubnt,unifi-6-plus)
 		emmc_copy_config
 		;;
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index c9cf30b1cea..6082cf5f47e 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -239,6 +239,21 @@ define Device/glinet_gl-mt3000
 endef
 TARGET_DEVICES += glinet_gl-mt3000
 
+define Device/glinet_gl-mt6000
+  DEVICE_VENDOR := GL.iNet
+  DEVICE_MODEL := GL-MT6000
+  DEVICE_DTS := mt7986a-glinet-gl-mt6000
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware e2fsprogs f2fsck mkf2fs
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-kernel | pad-to 32M | append-rootfs
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
+  ARTIFACTS := preloader.bin bl31-uboot.fip
+  ARTIFACT/preloader.bin := mt7986-bl2 emmc-ddr4
+  ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot glinet_gl-mt6000
+endef
+TARGET_DEVICES += glinet_gl-mt6000
+
 define Device/h3c_magic-nx30-pro
   DEVICE_VENDOR := H3C
   DEVICE_MODEL := Magic NX30 Pro