aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files/etc/diag.sh
diff options
context:
space:
mode:
authorChuanhong Guo <gch981213@gmail.com>2017-07-18 13:02:51 +0800
committerMathias Kresin <dev@kresin.me>2017-07-20 19:10:29 +0200
commita4c84b2d734f0cba40b3d0a2183dbf221e7356e5 (patch)
treed5400721563f7b72e6e15a926cb65c35dde7285d /target/linux/ramips/base-files/etc/diag.sh
parentb81c04382b5ddea0164993c2af0df7270bb95ee4 (diff)
downloadupstream-a4c84b2d734f0cba40b3d0a2183dbf221e7356e5.tar.gz
upstream-a4c84b2d734f0cba40b3d0a2183dbf221e7356e5.tar.bz2
upstream-a4c84b2d734f0cba40b3d0a2183dbf221e7356e5.zip
ramips: add support for Phicomm K2P
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the same time. However mt76 doesn't support it currently so there is no wireless available. Specification: - SoC: MediaTek MT7621AT - Flash: 16 MB - RAM: 128 MB - Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps) - Wireless radio: MT7615D on PCIE0 - UART: 1 x UART on PCB - 57600 8N1 Issue: - Wireless radio doesn't work due to the lack of driver. Flash instruction: Using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2,then follow the instruction to set device and tftp server IP address and input the firmware file name.U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc/diag.sh')
-rw-r--r--target/linux/ramips/base-files/etc/diag.sh9
1 files changed, 5 insertions, 4 deletions
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 531c8e055f..1349c00b32 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -157,6 +157,11 @@ get_status_led() {
hc5962)
status_led="$board:white:status"
;;
+ k2p|\
+ m3|\
+ miwifi-nano)
+ status_led="$board:blue:status"
+ ;;
linkits7688| \
linkits7688d)
[ "$1" = "upgrade" ] && status_led="mediatek:orange:wifi"
@@ -164,10 +169,6 @@ get_status_led() {
m2m)
status_led="$board:blue:wifi"
;;
- m3|\
- miwifi-nano)
- status_led="$board:blue:status"
- ;;
gl-mt300n-v2)
status_led="$board:red:wlan"
;;