lantiq: split base-files into subtargets

This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.

While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.

Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).

Applies alphabetic reordering to device cases in base-files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

3 files changed, 103 insertions, 0 deletions

diff --git a/target/linux/lantiq/xway_legacy/base-files/etc/board.d/01_leds b/target/linux/lantiq/xway_legacy/base-files/etc/board.d/01_leds
new file mode 100755
index 0000000000..4200dcb0c8
--- /dev/null
+++ b/target/linux/lantiq/xway_legacy/base-files/etc/board.d/01_leds
@@ -0,0 +1,41 @@
+#!/bin/sh
+#
+# Copyright (C) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/leds.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+led_wifi="$(get_dt_led wifi)"
+[ -n "$led_wifi" ] && ucidef_set_led_wlan "wifi" "wifi" "$led_wifi" "phy0tpt"
+
+led_usb="$(get_dt_led usb)"
+[ -n "$led_usb" ] && ucidef_set_led_usbdev "usb" "usb" "$led_usb" "1-1"
+
+led_usb2="$(get_dt_led usb2)"
+[ -n "$led_usb2" ] && ucidef_set_led_usbdev "usb2" "usb2" "$led_usb2" "2-1"
+
+led_dsl="$(get_dt_led dsl)"
+[ -n "$led_dsl" ] && {
+	led_internet="$(get_dt_led internet)"
+	if [ -n "$led_internet" ]; then
+		ucidef_set_led_default "dsl" "dsl" "$led_dsl" "0"
+		ucidef_set_led_netdev "internet" "internet" "$led_internet" "pppoe-wan"
+	else
+		ucidef_set_led_netdev "dsl" "dsl" "$led_dsl" "dsl0"
+	fi
+}
+
+board=$(board_name)
+
+case "$board" in
+arcadyan,arv4525pw)
+	ucidef_set_led_netdev "wifi" "wifi" "arv4525pw:green:wlan" "wlan0"
+	;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/lantiq/xway_legacy/base-files/etc/board.d/02_network b/target/linux/lantiq/xway_legacy/base-files/etc/board.d/02_network
new file mode 100755
index 0000000000..120857de4c
--- /dev/null
+++ b/target/linux/lantiq/xway_legacy/base-files/etc/board.d/02_network
@@ -0,0 +1,52 @@
+#!/bin/sh
+#
+# Copyright (C) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+. /lib/functions/lantiq.sh
+
+board_config_update
+
+annex="a"
+
+lan_mac=""
+wan_mac=""
+
+board=$(board_name)
+
+case "$board" in
+arcadyan,arv4520pw)
+	annex="b"
+	ucidef_add_switch "switch0" \
+		"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5t@eth0"
+	;;
+arcadyan,arv4525pw|\
+arcadyan,arv452cqw)
+	annex="b"
+	ucidef_set_interface_lan 'eth0'
+	;;
+*)
+	ucidef_set_interface_lan 'eth0'
+	;;
+esac
+
+ls /lib/modules/$(uname -r)/ltq_atm* 1> /dev/null 2>&1 && \
+	ucidef_add_atm_bridge 1 32 "llc" "bridged" "dsl"
+
+if lantiq_is_vdsl_system; then
+	ucidef_add_vdsl_modem "$annex" "av"
+else
+	ucidef_add_adsl_modem "$annex" "/lib/firmware/adsl.bin"
+fi
+
+ucidef_set_interface_wan "dsl0" "pppoe"
+
+[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" "$lan_mac"
+[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" "$wan_mac"
+
+board_config_flush
+
+exit 0
+
diff --git a/target/linux/lantiq/xway_legacy/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/xway_legacy/base-files/lib/upgrade/platform.sh
new file mode 100755
index 0000000000..d088601bb0
--- /dev/null
+++ b/target/linux/lantiq/xway_legacy/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,10 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+platform_check_image() {
+	return 0
+}
+
+platform_do_upgrade() {
+	default_do_upgrade "$1"
+}