ipq806x: Add support for linux-4.4

1)Changes

- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime

2)Testing

Tested on IPQ AP148 Board:
 a. NOR boot and NAND boot
 b. ethernet network and ath10k wifi
 c. ubi sysupgrade

UnTested
 dwc3 usb has not been validated on IPQ board(AP148)

3)Known Issues:
 Once we flash ubi image on AP148, and if we reset the board, uboot on
 first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
 and not what linux expects which causes errors when trying to mount rootfs.
 In order to test this, we can use the below steps:
  a. Flash the ubi image on board and don't reset the board
  b. load the kernel fit image in RAM and boot from there.

Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>

1 files changed, 0 insertions, 376 deletions

diff --git a/target/linux/ipq806x/patches-3.18/002-v3-spi-qup-Fix-incorrect-block-transfers.patch b/target/linux/ipq806x/patches-3.18/002-v3-spi-qup-Fix-incorrect-block-transfers.patch
deleted file mode 100644
index 62ee5b4fad..0000000000
--- a/target/linux/ipq806x/patches-3.18/002-v3-spi-qup-Fix-incorrect-block-transfers.patch
+++ /dev/null
@@ -1,376 +0,0 @@
-Content-Type: text/plain; charset="utf-8"
-MIME-Version: 1.0
-Content-Transfer-Encoding: 7bit
-Subject: [v3] spi: qup: Fix incorrect block transfers
-From: Andy Gross <agross@codeaurora.org>
-X-Patchwork-Id: 5007321
-Message-Id: <1412112088-25928-1-git-send-email-agross@codeaurora.org>
-To: Mark Brown <broonie@kernel.org>
-Cc: linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org,
-	linux-arm-kernel@lists.infradead.org, linux-arm-msm@vger.kernel.org,
-	"Ivan T. Ivanov" <iivanov@mm-sol.com>,
-	Bjorn Andersson <bjorn.andersson@sonymobile.com>,
-	Kumar Gala <galak@codeaurora.org>, Andy Gross <agross@codeaurora.org>
-Date: Tue, 30 Sep 2014 16:21:28 -0500
-
-This patch fixes a number of errors with the QUP block transfer mode.  Errors
-manifested themselves as input underruns, output overruns, and timed out
-transactions.
-
-The block mode does not require the priming that occurs in FIFO mode.  At the
-moment that the QUP is placed into the RUN state, the QUP will immediately raise
-an interrupt if the request is a write.  Therefore, there is no need to prime
-the pump.
-
-In addition, the block transfers require that whole blocks of data are
-read/written at a time.  The last block of data that completes a transaction may
-contain less than a full blocks worth of data.
-
-Each block of data results in an input/output service interrupt accompanied with
-a input/output block flag set.  Additional block reads/writes require clearing
-of the service flag.  It is ok to check for additional blocks of data in the
-ISR, but you have to ack every block you transfer.  Imbalanced acks result in
-early return from complete transactions with pending interrupts that still have
-to be ack'd.  The next transaction can be affected by these interrupts.
-Transactions are deemed complete when the MAX_INPUT or MAX_OUTPUT flag are set.
-
-Changes from v2:
-- Added in additional completion check so that transaction done is not
-  prematurely signaled.
-- Fixed various review comments.
-
-Changes from v1:
-- Split out read/write block function.
-- Removed extraneous checks for transfer length
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
-
----
-drivers/spi/spi-qup.c |  201 ++++++++++++++++++++++++++++++++++++-------------
- 1 file changed, 148 insertions(+), 53 deletions(-)
-
---- a/drivers/spi/spi-qup.c
-+++ b/drivers/spi/spi-qup.c
-@@ -82,6 +82,8 @@
- #define QUP_IO_M_MODE_BAM		3
- 
- /* QUP_OPERATIONAL fields */
-+#define QUP_OP_IN_BLOCK_READ_REQ	BIT(13)
-+#define QUP_OP_OUT_BLOCK_WRITE_REQ	BIT(12)
- #define QUP_OP_MAX_INPUT_DONE_FLAG	BIT(11)
- #define QUP_OP_MAX_OUTPUT_DONE_FLAG	BIT(10)
- #define QUP_OP_IN_SERVICE_FLAG		BIT(9)
-@@ -147,6 +149,7 @@ struct spi_qup {
- 	int			tx_bytes;
- 	int			rx_bytes;
- 	int			qup_v1;
-+	int			mode;
- 
- 	int			use_dma;
- 
-@@ -213,30 +216,14 @@ static int spi_qup_set_state(struct spi_
- 	return 0;
- }
- 
--
--static void spi_qup_fifo_read(struct spi_qup *controller,
--			    struct spi_transfer *xfer)
-+static void spi_qup_fill_read_buffer(struct spi_qup *controller,
-+	struct spi_transfer *xfer, u32 data)
- {
- 	u8 *rx_buf = xfer->rx_buf;
--	u32 word, state;
--	int idx, shift, w_size;
--
--	w_size = controller->w_size;
--
--	while (controller->rx_bytes < xfer->len) {
--
--		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
--		if (0 == (state & QUP_OP_IN_FIFO_NOT_EMPTY))
--			break;
--
--		word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
--
--		if (!rx_buf) {
--			controller->rx_bytes += w_size;
--			continue;
--		}
-+	int idx, shift;
- 
--		for (idx = 0; idx < w_size; idx++, controller->rx_bytes++) {
-+	if (rx_buf)
-+		for (idx = 0; idx < controller->w_size; idx++) {
- 			/*
- 			 * The data format depends on bytes per SPI word:
- 			 *  4 bytes: 0x12345678
-@@ -244,41 +231,139 @@ static void spi_qup_fifo_read(struct spi
- 			 *  1 byte : 0x00000012
- 			 */
- 			shift = BITS_PER_BYTE;
--			shift *= (w_size - idx - 1);
--			rx_buf[controller->rx_bytes] = word >> shift;
-+			shift *= (controller->w_size - idx - 1);
-+			rx_buf[controller->rx_bytes + idx] = data >> shift;
-+		}
-+
-+	controller->rx_bytes += controller->w_size;
-+}
-+
-+static void spi_qup_prepare_write_data(struct spi_qup *controller,
-+	struct spi_transfer *xfer, u32 *data)
-+{
-+	const u8 *tx_buf = xfer->tx_buf;
-+	u32 val;
-+	int idx;
-+
-+	*data = 0;
-+
-+	if (tx_buf)
-+		for (idx = 0; idx < controller->w_size; idx++) {
-+			val = tx_buf[controller->tx_bytes + idx];
-+			*data |= val << (BITS_PER_BYTE * (3 - idx));
- 		}
-+
-+	controller->tx_bytes += controller->w_size;
-+}
-+
-+static void spi_qup_fifo_read(struct spi_qup *controller,
-+			    struct spi_transfer *xfer)
-+{
-+	u32 data;
-+
-+	/* clear service request */
-+	writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
-+			controller->base + QUP_OPERATIONAL);
-+
-+	while (controller->rx_bytes < xfer->len) {
-+		if (!(readl_relaxed(controller->base + QUP_OPERATIONAL) &
-+		    QUP_OP_IN_FIFO_NOT_EMPTY))
-+			break;
-+
-+		data = readl_relaxed(controller->base + QUP_INPUT_FIFO);
-+
-+		spi_qup_fill_read_buffer(controller, xfer, data);
- 	}
- }
- 
- static void spi_qup_fifo_write(struct spi_qup *controller,
--			    struct spi_transfer *xfer)
-+	struct spi_transfer *xfer)
- {
--	const u8 *tx_buf = xfer->tx_buf;
--	u32 word, state, data;
--	int idx, w_size;
-+	u32 data;
- 
--	w_size = controller->w_size;
-+	/* clear service request */
-+	writel_relaxed(QUP_OP_OUT_SERVICE_FLAG,
-+		controller->base + QUP_OPERATIONAL);
- 
- 	while (controller->tx_bytes < xfer->len) {
- 
--		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
--		if (state & QUP_OP_OUT_FIFO_FULL)
-+		if (readl_relaxed(controller->base + QUP_OPERATIONAL) &
-+				QUP_OP_OUT_FIFO_FULL)
- 			break;
- 
--		word = 0;
--		for (idx = 0; idx < w_size; idx++, controller->tx_bytes++) {
-+		spi_qup_prepare_write_data(controller, xfer, &data);
-+		writel_relaxed(data, controller->base + QUP_OUTPUT_FIFO);
- 
--			if (!tx_buf) {
--				controller->tx_bytes += w_size;
--				break;
--			}
-+	}
-+}
- 
--			data = tx_buf[controller->tx_bytes];
--			word |= data << (BITS_PER_BYTE * (3 - idx));
--		}
-+static void spi_qup_block_read(struct spi_qup *controller,
-+	struct spi_transfer *xfer)
-+{
-+	u32 data;
-+	u32 reads_per_blk = controller->in_blk_sz >> 2;
-+	u32 num_words = (xfer->len - controller->rx_bytes) / controller->w_size;
-+	int i;
-+
-+	do {
-+		/* ACK by clearing service flag */
-+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
-+			controller->base + QUP_OPERATIONAL);
-+
-+		/* transfer up to a block size of data in a single pass */
-+		for (i = 0; num_words && i < reads_per_blk; i++, num_words--) {
-+
-+			/* read data and fill up rx buffer */
-+			data = readl_relaxed(controller->base + QUP_INPUT_FIFO);
-+			spi_qup_fill_read_buffer(controller, xfer, data);
-+		}
-+
-+		/* check to see if next block is ready */
-+		if (!(readl_relaxed(controller->base + QUP_OPERATIONAL) &
-+			QUP_OP_IN_BLOCK_READ_REQ))
-+			break;
- 
--		writel_relaxed(word, controller->base + QUP_OUTPUT_FIFO);
--	}
-+	} while (num_words);
-+
-+	/*
-+	 * Due to extra stickiness of the QUP_OP_IN_SERVICE_FLAG during block
-+	 * reads, it has to be cleared again at the very end
-+	 */
-+	if (readl_relaxed(controller->base + QUP_OPERATIONAL) &
-+		QUP_OP_MAX_INPUT_DONE_FLAG)
-+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
-+			controller->base + QUP_OPERATIONAL);
-+
-+}
-+
-+static void spi_qup_block_write(struct spi_qup *controller,
-+	struct spi_transfer *xfer)
-+{
-+	u32 data;
-+	u32 writes_per_blk = controller->out_blk_sz >> 2;
-+	u32 num_words = (xfer->len - controller->tx_bytes) / controller->w_size;
-+	int i;
-+
-+	do {
-+		/* ACK by clearing service flag */
-+		writel_relaxed(QUP_OP_OUT_SERVICE_FLAG,
-+			controller->base + QUP_OPERATIONAL);
-+
-+		/* transfer up to a block size of data in a single pass */
-+		for (i = 0; num_words && i < writes_per_blk; i++, num_words--) {
-+
-+			/* swizzle the bytes for output and write out */
-+			spi_qup_prepare_write_data(controller, xfer, &data);
-+			writel_relaxed(data,
-+				controller->base + QUP_OUTPUT_FIFO);
-+		}
-+
-+		/* check to see if next block is ready */
-+		if (!(readl_relaxed(controller->base + QUP_OPERATIONAL) &
-+			QUP_OP_OUT_BLOCK_WRITE_REQ))
-+			break;
-+
-+	} while (num_words);
- }
- 
- static void qup_dma_callback(void *data)
-@@ -515,9 +600,9 @@ static irqreturn_t spi_qup_qup_irq(int i
- 
- 	writel_relaxed(qup_err, controller->base + QUP_ERROR_FLAGS);
- 	writel_relaxed(spi_err, controller->base + SPI_ERROR_FLAGS);
--	writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
- 
- 	if (!xfer) {
-+		writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
- 		dev_err_ratelimited(controller->dev, "unexpected irq %08x %08x %08x\n",
- 				    qup_err, spi_err, opflags);
- 		return IRQ_HANDLED;
-@@ -546,11 +631,19 @@ static irqreturn_t spi_qup_qup_irq(int i
- 	}
- 
- 	if (!controller->use_dma) {
--		if (opflags & QUP_OP_IN_SERVICE_FLAG)
--			spi_qup_fifo_read(controller, xfer);
-+		if (opflags & QUP_OP_IN_SERVICE_FLAG) {
-+			if (opflags & QUP_OP_IN_BLOCK_READ_REQ)
-+				spi_qup_block_read(controller, xfer);
-+			else
-+				spi_qup_fifo_read(controller, xfer);
-+		}
- 
--		if (opflags & QUP_OP_OUT_SERVICE_FLAG)
--			spi_qup_fifo_write(controller, xfer);
-+		if (opflags & QUP_OP_OUT_SERVICE_FLAG) {
-+			if (opflags & QUP_OP_OUT_BLOCK_WRITE_REQ)
-+				spi_qup_block_write(controller, xfer);
-+			else
-+				spi_qup_fifo_write(controller, xfer);
-+		}
- 	}
- 
- 	spin_lock_irqsave(&controller->lock, flags);
-@@ -558,7 +651,8 @@ static irqreturn_t spi_qup_qup_irq(int i
- 	controller->xfer = xfer;
- 	spin_unlock_irqrestore(&controller->lock, flags);
- 
--	if (controller->rx_bytes == xfer->len || error)
-+	if ((controller->rx_bytes == xfer->len &&
-+		(opflags & QUP_OP_MAX_INPUT_DONE_FLAG)) || error)
- 		complete(&controller->done);
- 
- 	return IRQ_HANDLED;
-@@ -569,7 +663,7 @@ static irqreturn_t spi_qup_qup_irq(int i
- static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
- {
- 	struct spi_qup *controller = spi_master_get_devdata(spi->master);
--	u32 config, iomode, mode;
-+	u32 config, iomode;
- 	int ret, n_words, w_size;
- 	size_t dma_align = dma_get_cache_alignment();
- 	u32 dma_available = 0;
-@@ -607,7 +701,7 @@ static int spi_qup_io_config(struct spi_
- 		dma_available = 1;
- 
- 	if (n_words <= (controller->in_fifo_sz / sizeof(u32))) {
--		mode = QUP_IO_M_MODE_FIFO;
-+		controller->mode = QUP_IO_M_MODE_FIFO;
- 		writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
- 		writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
- 		/* must be zero for FIFO */
-@@ -615,7 +709,7 @@ static int spi_qup_io_config(struct spi_
- 		writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
- 		controller->use_dma = 0;
- 	} else if (!dma_available) {
--		mode = QUP_IO_M_MODE_BLOCK;
-+		controller->mode = QUP_IO_M_MODE_BLOCK;
- 		writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
- 		writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
- 		/* must be zero for BLOCK and BAM */
-@@ -623,7 +717,7 @@ static int spi_qup_io_config(struct spi_
- 		writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
- 		controller->use_dma = 0;
- 	} else {
--		mode = QUP_IO_M_MODE_DMOV;
-+		controller->mode = QUP_IO_M_MODE_DMOV;
- 		writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
- 		writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
- 		controller->use_dma = 1;
-@@ -638,8 +732,8 @@ static int spi_qup_io_config(struct spi_
- 	else
- 		iomode |= QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN;
- 
--	iomode |= (mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
--	iomode |= (mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
-+	iomode |= (controller->mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
-+	iomode |= (controller->mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
- 
- 	writel_relaxed(iomode, controller->base + QUP_IO_M_MODES);
- 
-@@ -724,7 +818,8 @@ static int spi_qup_transfer_one(struct s
- 			goto exit;
- 		}
- 
--		spi_qup_fifo_write(controller, xfer);
-+		if (controller->mode == QUP_IO_M_MODE_FIFO)
-+			spi_qup_fifo_write(controller, xfer);
- 
- 		if (spi_qup_set_state(controller, QUP_STATE_RUN)) {
- 			dev_warn(controller->dev, "cannot set EXECUTE state\n");
-@@ -741,6 +836,7 @@ exit:
- 	if (!ret)
- 		ret = controller->error;
- 	spin_unlock_irqrestore(&controller->lock, flags);
-+
- 	return ret;
- }
-