diff options
| author | Hans Geiblinger <cybrnook2002@yahoo.com> | 2020-09-09 18:45:02 -0400 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2020-09-25 19:31:51 +0200 |
| commit | a9071d02b5ab11fbd73ea42076a09f2fd8136517 (patch) | |
| tree | 2379c735897dff660a83b0ff68171ba886202fd3 /target/linux/ipq40xx/base-files/lib | |
| parent | e24635710c7e6444afa463c59f3d81fe634eb3c7 (diff) | |
| download | upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.tar.gz upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.tar.bz2 upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.zip | |
ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ipq40xx/base-files/lib')
4 files changed, 6 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh index 4d8113698e..0d606c75b5 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -15,7 +15,8 @@ preinit_set_mac_address() { base_mac=$(cat /sys/class/net/eth0/address) ip link set dev eth1 address $(macaddr_add "${base_mac}" +1) ;; - linksys,ea8300) + linksys,ea8300|\ + linksys,mr8300) base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) ip link set dev eth0 address "${base_mac}" ip link set dev eth1 address $(macaddr_add "${base_mac}" 1) diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh index f94116de6e..0311922f08 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh @@ -8,6 +8,7 @@ set_preinit_iface() { ezviz,cs-w3-wd1200g-eup| \ glinet,gl-b1300| \ linksys,ea8300| \ + linksys,mr8300| \ meraki,mr33| \ zyxel,nbg6617) ifname=eth0 diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh index 9d9b47eeaa..de09d34aef 100755 --- a/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh @@ -16,7 +16,7 @@ linksys_get_target_firmware() { "${cur_boot_part}" "${mtd_ubi0}" fi - # OEM U-Boot for EA6350v3 and EA8300; bootcmd= + # OEM U-Boot for EA6350v3, EA8300 and MR8300; bootcmd= # if test $auto_recovery = no; # then bootipq; # elif test $boot_part = 1; diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index e09ab0344b..09ea396469 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -102,7 +102,8 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; linksys,ea6350v3 |\ - linksys,ea8300) + linksys,ea8300 |\ + linksys,mr8300) platform_do_upgrade_linksys "$1" ;; meraki,mr33) |