diff options
| author | Hans Geiblinger <cybrnook2002@yahoo.com> | 2020-09-09 18:45:02 -0400 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2020-09-25 19:31:51 +0200 |
| commit | a9071d02b5ab11fbd73ea42076a09f2fd8136517 (patch) | |
| tree | 2379c735897dff660a83b0ff68171ba886202fd3 /target/linux/ipq40xx/base-files/etc | |
| parent | e24635710c7e6444afa463c59f3d81fe634eb3c7 (diff) | |
| download | upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.tar.gz upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.tar.bz2 upstream-a9071d02b5ab11fbd73ea42076a09f2fd8136517.zip | |
ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc')
3 files changed, 10 insertions, 5 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index d744e9b7e2..86787eeffd 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -53,7 +53,8 @@ ipq40xx_setup_interfaces() ;; avm,fritzbox-4040|\ linksys,ea6350v3|\ - linksys,ea8300) + linksys,ea8300|\ + linksys,mr8300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 7a7464cf9a..f33d3f331c 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -39,7 +39,8 @@ case "$FIRMWARE" in openmesh,a62) caldata_extract "0:ART" 0x9000 0x2f20 ;; - linksys,ea8300) + linksys,ea8300 |\ + linksys,mr8300) caldata_extract "ART" 0x9000 0x2f20 # OEM assigns 4 sequential MACs ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4)) @@ -121,7 +122,8 @@ case "$FIRMWARE" in caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) ;; - linksys,ea8300) + linksys,ea8300 |\ + linksys,mr8300) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2) ;; @@ -217,7 +219,8 @@ case "$FIRMWARE" in caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) ;; - linksys,ea8300) + linksys,ea8300 |\ + linksys,mr8300) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3) ;; diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount index b9d625e296..d2a4abcadd 100755 --- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -9,7 +9,8 @@ boot() { echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s - ;; linksys,ea6350v3|\ - linksys,ea8300) + linksys,ea8300|\ + linksys,mr8300) mtd resetbc s_env || true ;; esac |