diff options
author | Steven Lin <steven.lin@senao.com> | 2018-10-19 16:55:08 +0800 |
---|---|---|
committer | Mathias Kresin <dev@kresin.me> | 2018-12-05 09:40:32 +0100 |
commit | 2b4ac79a791d9451f601d494dde2e71864174358 (patch) | |
tree | efdddf6c8757a2f19f4998ef1e1a25e152a81b79 /target/linux/ipq40xx/base-files/etc/board.d | |
parent | e261c8b76407ebd2d8289e3522bd02e5bd6e8552 (diff) | |
download | upstream-2b4ac79a791d9451f601d494dde2e71864174358.tar.gz upstream-2b4ac79a791d9451f601d494dde2e71864174358.tar.bz2 upstream-2b4ac79a791d9451f601d494dde2e71864174358.zip |
ipq40xx: add support for EnGenius EAP1300
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc/board.d')
-rwxr-xr-x | target/linux/ipq40xx/base-files/etc/board.d/01_leds | 6 | ||||
-rwxr-xr-x | target/linux/ipq40xx/base-files/etc/board.d/02_network | 13 |
2 files changed, 13 insertions, 6 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index ab2f77ee10..5e382c03a7 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -23,6 +23,12 @@ avm,fritzbox-4040) ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1" ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e" ;; +engenius,eap1300) + ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0" + ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt" + ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0" + ;; glinet,gl-b1300) ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt" ;; diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 5c90ef136f..d73914c7c1 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -33,6 +33,13 @@ avm,fritzbox-4040) compex,wpj428) ucidef_set_interface_lan "eth0 eth1" ;; +engenius,eap1300 |\ +meraki,mr33 |\ +netgear,ex6100v2 |\ +netgear,ex6150v2 |\ +zyxel,wre6606) + ucidef_set_interface_lan "eth0" + ;; glinet,gl-b1300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ @@ -42,12 +49,6 @@ openmesh,a42 |\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; -meraki,mr33 |\ -netgear,ex6100v2 |\ -netgear,ex6150v2 |\ -zyxel,wre6606) - ucidef_set_interface_lan "eth0" - ;; zyxel,nbg6617) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ |