brcm2708: rename all patches from raspberrypi git tree to use 950 prefix

Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support

Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 88 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.9/950-0017-spi-bcm2835-Remove-unused-code.patch b/target/linux/brcm2708/patches-4.9/950-0017-spi-bcm2835-Remove-unused-code.patch
new file mode 100644
index 0000000000..08577fce2a
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.9/950-0017-spi-bcm2835-Remove-unused-code.patch
@@ -0,0 +1,88 @@
+From 21f7f9d8146dd9e5a860198781febf78aafee3d1 Mon Sep 17 00:00:00 2001
+From: Phil Elwell <phil@raspberrypi.org>
+Date: Tue, 8 Nov 2016 21:35:38 +0000
+Subject: [PATCH] spi-bcm2835: Remove unused code
+
+---
+ drivers/spi/spi-bcm2835.c | 61 -----------------------------------------------
+ 1 file changed, 61 deletions(-)
+
+--- a/drivers/spi/spi-bcm2835.c
++++ b/drivers/spi/spi-bcm2835.c
+@@ -679,17 +679,8 @@ static void bcm2835_spi_set_cs(struct sp
+ 	bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+ }
+ 
+-static int chip_match_name(struct gpio_chip *chip, void *data)
+-{
+-	return !strcmp(chip->label, data);
+-}
+-
+ static int bcm2835_spi_setup(struct spi_device *spi)
+ {
+-	int err;
+-	struct gpio_chip *chip;
+-	struct device_node *pins;
+-	u32 pingroup_index;
+ 	/*
+ 	 * sanity checking the native-chipselects
+ 	 */
+@@ -707,58 +698,6 @@ static int bcm2835_spi_setup(struct spi_
+ 		return -EINVAL;
+ 	}
+ 
+-#if 0
+-	/* now translate native cs to GPIO */
+-	/* first look for chip select pins in the devices pin groups */
+-	for (pingroup_index = 0;
+-	     (pins = of_parse_phandle(spi->master->dev.of_node,
+-				     "pinctrl-0",
+-				      pingroup_index)) != 0;
+-	     pingroup_index++) {
+-		u32 pin;
+-		u32 pin_index;
+-		for (pin_index = 0;
+-		     of_property_read_u32_index(pins,
+-						"brcm,pins",
+-						pin_index,
+-						&pin) == 0;
+-		     pin_index++) {
+-			if (((spi->chip_select == 0) &&
+-			     ((pin == 8) || (pin == 36) || (pin == 46))) ||
+-			    ((spi->chip_select == 1) &&
+-			     ((pin == 7) || (pin == 35)))) {
+-				spi->cs_gpio = pin;
+-				break;
+-			}
+-		}
+-		of_node_put(pins);
+-	}
+-	/* if that fails, assume GPIOs 7-11 are used */
+-	if (!gpio_is_valid(spi->cs_gpio) ) {
+-		/* get the gpio chip for the base */
+-		chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
+-		if (!chip)
+-			return 0;
+-
+-		/* and calculate the real CS */
+-		spi->cs_gpio = chip->base + 8 - spi->chip_select;
+-	}
+-
+-	/* and set up the "mode" and level */
+-	dev_info(&spi->dev, "setting up native-CS%i as GPIO %i\n",
+-		 spi->chip_select, spi->cs_gpio);
+-
+-	/* set up GPIO as output and pull to the correct level */
+-	err = gpio_direction_output(spi->cs_gpio,
+-				    (spi->mode & SPI_CS_HIGH) ? 0 : 1);
+-	if (err) {
+-		dev_err(&spi->dev,
+-			"could not set CS%i gpio %i as output: %i",
+-			spi->chip_select, spi->cs_gpio, err);
+-		return err;
+-	}
+-#endif
+-
+ 	return 0;
+ }
+