brcm2708: add kernel 4.14 support

Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89

Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""

Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
  MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch

Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.

Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 32 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.14/950-0322-ov5647-dt-add-device-tree-for-PWDN-control.patch b/target/linux/brcm2708/patches-4.14/950-0322-ov5647-dt-add-device-tree-for-PWDN-control.patch
new file mode 100644
index 0000000000..b0152b4753
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.14/950-0322-ov5647-dt-add-device-tree-for-PWDN-control.patch
@@ -0,0 +1,32 @@
+From 09036bbc1f3f3c80cc9f611e4b1fc138a87b9743 Mon Sep 17 00:00:00 2001
+From: Dave Stevenson <dave.stevenson@raspberrypi.org>
+Date: Thu, 18 May 2017 15:37:49 +0100
+Subject: [PATCH 322/454] ov5647: dt: add device tree for PWDN control
+
+Add optional GPIO pwdn to connect to the PWDN line on the sensor.
+
+Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
+---
+ Documentation/devicetree/bindings/media/i2c/ov5647.txt | 4 ++++
+ 1 file changed, 4 insertions(+)
+
+--- a/Documentation/devicetree/bindings/media/i2c/ov5647.txt
++++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
+@@ -10,6 +10,9 @@ Required properties:
+ - reg			: I2C slave address of the sensor.
+ - clocks		: Reference to the xclk clock.
+ 
++Optional Properties:
++- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
++
+ The common video interfaces bindings (see video-interfaces.txt) should be
+ used to specify link to the image data receiver. The OV5647 device
+ node should contain one 'port' child node with an 'endpoint' subnode.
+@@ -26,6 +29,7 @@ Example:
+ 			compatible = "ovti,ov5647";
+ 			reg = <0x36>;
+ 			clocks = <&camera_clk>;
++			pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+ 			port {
+ 				camera_1: endpoint {
+ 					remote-endpoint = <&csi1_ep1>;