aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch
diff options
context:
space:
mode:
authorStijn Tintel <stijn@linux-ipv6.be>2018-11-10 13:03:18 +0200
committerStijn Tintel <stijn@linux-ipv6.be>2018-12-18 23:19:21 +0200
commitf5919b65d4c671fd5083838c7a445f319f9a13c8 (patch)
tree2c791d2a5dea5bbbb0b85f86f74afce2647c0726 /target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch
parent822b4c3b250a254e74407056ccfd5c6aa38da162 (diff)
downloadupstream-f5919b65d4c671fd5083838c7a445f319f9a13c8.tar.gz
upstream-f5919b65d4c671fd5083838c7a445f319f9a13c8.tar.bz2
upstream-f5919b65d4c671fd5083838c7a445f319f9a13c8.zip
brcm2708: add kernel 4.14 support
Patch generation process: - rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable - git format-patch v4.14.89 Patches skipped during rebase: - lan78xx: Read MAC address from DT if present - lan78xx: Enable LEDs and auto-negotiation - Revert "softirq: Let ksoftirqd do its job" - sc16is7xx: Fix for multi-channel stall - lan78xx: Ignore DT MAC address if already valid - lan78xx: Simple patch to prevent some crashes - tcp_write_queue_purge clears all the SKBs in the write queue - Revert "lan78xx: Simple patch to prevent some crashes" - lan78xx: Connect phy early - Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro - Revert "Revert "softirq: Let ksoftirqd do its job"" - ASoC: cs4265: SOC_SINGLE register value error fix - Revert "ASoC: cs4265: SOC_SINGLE register value error fix" - Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends" - Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"" Patches dropped after rebase: - net: Add non-mainline source for rtl8192cu wlan - net: Fix rtl8192cu build errors on other platforms - brcm: adds support for BCM43341 wifi - brcmfmac: Mute expected startup 'errors' - ARM64: Fix build break for RTL8187/RTL8192CU wifi - ARM64: Enable RTL8187/RTL8192CU wifi in build config - This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator - brcmfmac: add CLM download support - brcmfmac: request_firmware_direct is quieter - Sets the BCDC priority to constant 0 - brcmfmac: Disable ARP offloading when promiscuous - brcmfmac: Avoid possible out-of-bounds read - brcmfmac: Delete redundant length check - net: rtl8192cu: Normalize indentation - net: rtl8192cu: Fix implicit fallthrough warnings - Revert "Sets the BCDC priority to constant 0" - media: cxd2880: Bump to match 4.18.y version - media: cxd2880-spi: Bump to match 4.18.y version - Revert "mm: alloc_contig: re-allow CMA to compact FS pages" - Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages"" - cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT - 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch - 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch Make I2C built-in instead of modular as in upstream defconfig; also the easiest way to get MFD_ARIZONA enabled, which is required by kmod-sound-soc-rpi-cirrus. Add missing compatible strings from 4.9/960-add-rasbperrypi-compatible.patch, using upstream names for compute modules. Add extra patch to enable the LEDs on lan78xx. Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y) Runtime-tested: bcm2708, bcm2710 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Diffstat (limited to 'target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch')
-rw-r--r--target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch1759
1 files changed, 1759 insertions, 0 deletions
diff --git a/target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch b/target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch
new file mode 100644
index 0000000000..d66a88b768
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.14/950-0260-Add-overlay-for-Semtech-SX150X-I2C-GPIO-Expanders.patch
@@ -0,0 +1,1759 @@
+From 0b2881369a38b0a139ae4a256ea1953750fb6a76 Mon Sep 17 00:00:00 2001
+From: wavelet2 <a3d35232@btinternet.com>
+Date: Thu, 22 Mar 2018 19:08:02 +0000
+Subject: [PATCH 260/454] Add overlay for Semtech SX150X I2C GPIO Expanders
+
+---
+ arch/arm/boot/dts/overlays/Makefile | 1 +
+ arch/arm/boot/dts/overlays/README | 19 +
+ arch/arm/boot/dts/overlays/sx150x-overlay.dts | 1706 +++++++++++++++++
+ 3 files changed, 1726 insertions(+)
+ create mode 100644 arch/arm/boot/dts/overlays/sx150x-overlay.dts
+
+--- a/arch/arm/boot/dts/overlays/Makefile
++++ b/arch/arm/boot/dts/overlays/Makefile
+@@ -120,6 +120,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
+ spi2-2cs.dtbo \
+ spi2-3cs.dtbo \
+ superaudioboard.dtbo \
++ sx150x.dtbo \
+ tinylcd35.dtbo \
+ uart0.dtbo \
+ uart1.dtbo \
+--- a/arch/arm/boot/dts/overlays/README
++++ b/arch/arm/boot/dts/overlays/README
+@@ -1703,6 +1703,25 @@ Load: dtoverlay=superaudioboard,<param
+ Params: gpiopin GPIO pin for codec reset
+
+
++Name: sx150x
++Info: Configures the Semtech SX150X I2C GPIO expanders.
++Load: dtoverlay=sx150x,<param>=<val>
++Params: sx150<x>-<n>-<m> Enables SX150X device on I2C#<n> with slave
++ address <m>. <x> may be 1-9. <n> may be 0 or 1.
++ Permissible values of <m> (which is denoted in
++ hex) depend on the device variant. For SX1501,
++ SX1502, SX1504 and SX1505, <m> may be 20 or 21.
++ For SX1503 and SX1506, <m> may be 20. For
++ SX1507 and SX1509, <m> may be 3E, 3F, 70 or 71.
++ For SX1508, <m> may be 20, 21, 22 or 23.
++
++ sx150<x>-<n>-<m>-int-gpio
++ Integer, enables interrupts on SX150X device on
++ I2C#<n> with slave address <m>, specifies
++ the GPIO pin to which NINT output of SX150X is
++ connected.
++
++
+ Name: tinylcd35
+ Info: 3.5" Color TFT Display by www.tinylcd.com
+ Options: Touch, RTC, keypad
+--- /dev/null
++++ b/arch/arm/boot/dts/overlays/sx150x-overlay.dts
+@@ -0,0 +1,1706 @@
++// Definitions for SX150x I2C GPIO Expanders from Semtech
++
++// dtparams:
++// sx150<x>-<n>-<m> - Enables SX150X device on I2C#<n> with slave address <m>. <x> may be 1-9.
++// <n> may be 0 or 1. Permissible values of <m> (which is denoted in hex)
++// depend on the device variant.
++// For SX1501, SX1502, SX1504 and SX1505, <m> may be 20 or 21.
++// For SX1503 and SX1506, <m> may be 20.
++// For SX1507 and SX1509, <m> may be 3E, 3F, 70 or 71.
++// For SX1508, <m> may be 20, 21, 22 or 23.
++// sx150<x>-<n>-<m>-int-gpio - Integer, enables interrupts on SX150X device on I2C#<n> with slave address <m>,
++// specifies the GPIO pin to which NINT output of SX150X is connected.
++//
++//
++// Example 1: A single SX1505 device on I2C#1 with its slave address set to 0x20 and NINT output connected to GPIO25:
++// dtoverlay=sx150x:sx1505-1-20,sx1505-1-20-int-gpio=25
++//
++// Example 2: Two SX1507 devices on I2C#0 with their slave addresses set to 0x3E and 0x70 (interrupts not used):
++// dtoverlay=sx150x:sx1507-0-3E,sx1507-0-70
++
++/dts-v1/;
++/plugin/;
++
++/ {
++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
++
++ // Enable I2C#0 interface
++ fragment@0 {
++ target = <&i2c0>;
++ __dormant__ {
++ status = "okay";
++ };
++ };
++
++ // Enable I2C#1 interface
++ fragment@1 {
++ target = <&i2c1>;
++ __dormant__ {
++ status = "okay";
++ };
++ };
++
++ // Enable a SX1501 on I2C#0 at slave addr 0x20
++ fragment@2 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1501_0_20: sx150x@20 {
++ compatible = "semtech,sx1501q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1501-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1501 on I2C#1 at slave addr 0x20
++ fragment@3 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1501_1_20: sx150x@20 {
++ compatible = "semtech,sx1501q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1501 on I2C#0 at slave addr 0x21
++ fragment@4 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1501_0_21: sx150x@21 {
++ compatible = "semtech,sx1501q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1501-0-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1501 on I2C#1 at slave addr 0x21
++ fragment@5 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1501_1_21: sx150x@21 {
++ compatible = "semtech,sx1501q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1502 on I2C#0 at slave addr 0x20
++ fragment@6 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1502_0_20: sx150x@20 {
++ compatible = "semtech,sx1502q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1502-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1502 on I2C#1 at slave addr 0x20
++ fragment@7 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1502_1_20: sx150x@20 {
++ compatible = "semtech,sx1502q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1502-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1502 on I2C#0 at slave addr 0x21
++ fragment@8 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1502_0_21: sx150x@21 {
++ compatible = "semtech,sx1502q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1502-0-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1502 on I2C#1 at slave addr 0x21
++ fragment@9 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1502_1_21: sx150x@21 {
++ compatible = "semtech,sx1502q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1503 on I2C#0 at slave addr 0x20
++ fragment@10 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1503_0_20: sx150x@20 {
++ compatible = "semtech,sx1503q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1503-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1503 on I2C#1 at slave addr 0x20
++ fragment@11 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1503_1_20: sx150x@20 {
++ compatible = "semtech,sx1503q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1503-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1504 on I2C#0 at slave addr 0x20
++ fragment@12 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1504_0_20: sx150x@20 {
++ compatible = "semtech,sx1504q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1504-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1504 on I2C#1 at slave addr 0x20
++ fragment@13 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1504_1_20: sx150x@20 {
++ compatible = "semtech,sx1504q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1504 on I2C#0 at slave addr 0x21
++ fragment@14 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1504_0_21: sx150x@21 {
++ compatible = "semtech,sx1504q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1504-0-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1504 on I2C#1 at slave addr 0x21
++ fragment@15 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1504_1_21: sx150x@21 {
++ compatible = "semtech,sx1504q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1505 on I2C#0 at slave addr 0x20
++ fragment@16 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1505_0_20: sx150x@20 {
++ compatible = "semtech,sx1505q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1505-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1505 on I2C#1 at slave addr 0x20
++ fragment@17 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1505_1_20: sx150x@20 {
++ compatible = "semtech,sx1505q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1505-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1505 on I2C#0 at slave addr 0x21
++ fragment@18 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1505_0_21: sx150x@21 {
++ compatible = "semtech,sx1505q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1505-0-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1505 on I2C#1 at slave addr 0x21
++ fragment@19 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1505_1_21: sx150x@21 {
++ compatible = "semtech,sx1505q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1505-1-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1506 on I2C#0 at slave addr 0x20
++ fragment@20 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1506_0_20: sx150x@20 {
++ compatible = "semtech,sx1506q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1506-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1506 on I2C#1 at slave addr 0x20
++ fragment@21 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1506_1_20: sx150x@20 {
++ compatible = "semtech,sx1506q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1506-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#0 at slave addr 0x3E
++ fragment@22 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_0_3E: sx150x@3E {
++ compatible = "semtech,sx1507q";
++ reg = <0x3E>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3E-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#1 at slave addr 0x3E
++ fragment@23 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_1_3E: sx150x@3E {
++ compatible = "semtech,sx1507q";
++ reg = <0x3E>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3E-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#0 at slave addr 0x3F
++ fragment@24 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_0_3F: sx150x@3F {
++ compatible = "semtech,sx1507q";
++ reg = <0x3F>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3F-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#1 at slave addr 0x3F
++ fragment@25 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_1_3F: sx150x@3F {
++ compatible = "semtech,sx1507q";
++ reg = <0x3F>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3F-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#0 at slave addr 0x70
++ fragment@26 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_0_70: sx150x@70 {
++ compatible = "semtech,sx1507q";
++ reg = <0x70>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507-0-70-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#1 at slave addr 0x70
++ fragment@27 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_1_70: sx150x@70 {
++ compatible = "semtech,sx1507q";
++ reg = <0x70>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507-1-70-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#0 at slave addr 0x71
++ fragment@28 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_0_71: sx150x@71 {
++ compatible = "semtech,sx1507q";
++ reg = <0x71>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507-0-71-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1507 on I2C#1 at slave addr 0x71
++ fragment@29 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1507_1_71: sx150x@71 {
++ compatible = "semtech,sx1507q";
++ reg = <0x71>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1507-1-71-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#0 at slave addr 0x20
++ fragment@30 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_0_20: sx150x@20 {
++ compatible = "semtech,sx1508q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#1 at slave addr 0x20
++ fragment@31 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_1_20: sx150x@20 {
++ compatible = "semtech,sx1508q";
++ reg = <0x20>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-20-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#0 at slave addr 0x21
++ fragment@32 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_0_21: sx150x@21 {
++ compatible = "semtech,sx1508q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#1 at slave addr 0x21
++ fragment@33 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_1_21: sx150x@21 {
++ compatible = "semtech,sx1508q";
++ reg = <0x21>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-21-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#0 at slave addr 0x22
++ fragment@34 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_0_22: sx150x@22 {
++ compatible = "semtech,sx1508q";
++ reg = <0x22>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-22-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#1 at slave addr 0x22
++ fragment@35 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_1_22: sx150x@22 {
++ compatible = "semtech,sx1508q";
++ reg = <0x22>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-22-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#0 at slave addr 0x23
++ fragment@36 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_0_23: sx150x@23 {
++ compatible = "semtech,sx1508q";
++ reg = <0x23>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-23-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1508 on I2C#1 at slave addr 0x23
++ fragment@37 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1508_1_23: sx150x@23 {
++ compatible = "semtech,sx1508q";
++ reg = <0x23>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-23-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#0 at slave addr 0x3E
++ fragment@38 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_0_3E: sx150x@3E {
++ compatible = "semtech,sx1509q";
++ reg = <0x3E>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3E-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#1 at slave addr 0x3E
++ fragment@39 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_1_3E: sx150x@3E {
++ compatible = "semtech,sx1509q";
++ reg = <0x3E>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3E-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#0 at slave addr 0x3F
++ fragment@40 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_0_3F: sx150x@3F {
++ compatible = "semtech,sx1509q";
++ reg = <0x3F>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3F-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#1 at slave addr 0x3F
++ fragment@41 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_1_3F: sx150x@3F {
++ compatible = "semtech,sx1509q";
++ reg = <0x3F>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3F-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#0 at slave addr 0x70
++ fragment@42 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_0_70: sx150x@70 {
++ compatible = "semtech,sx1509q";
++ reg = <0x70>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509-0-70-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#1 at slave addr 0x70
++ fragment@43 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_1_70: sx150x@70 {
++ compatible = "semtech,sx1509q";
++ reg = <0x70>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509-1-70-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#0 at slave addr 0x71
++ fragment@44 {
++ target = <&i2c0>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_0_71: sx150x@71 {
++ compatible = "semtech,sx1509q";
++ reg = <0x71>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509-0-71-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable a SX1509 on I2C#1 at slave addr 0x71
++ fragment@45 {
++ target = <&i2c1>;
++ __dormant__ {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ sx1509_1_71: sx150x@71 {
++ compatible = "semtech,sx1509q";
++ reg = <0x71>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ #interrupt-cells = <2>;
++ interrupts = <25 2>; /* 1st word overwritten by sx1509-1-71-int-gpio parameter
++ 2nd word is 2 for falling-edge triggered */
++ status = "okay";
++ };
++ };
++ };
++
++ // Enable interrupts for a SX1501 on I2C#0 at slave addr 0x20
++ fragment@46 {
++ target = <&sx1501_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1501 on I2C#1 at slave addr 0x20
++ fragment@47 {
++ target = <&sx1501_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1501 on I2C#0 at slave addr 0x21
++ fragment@48 {
++ target = <&sx1501_0_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1501 on I2C#1 at slave addr 0x21
++ fragment@49 {
++ target = <&sx1501_1_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1502 on I2C#0 at slave addr 0x20
++ fragment@50 {
++ target = <&sx1502_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1502 on I2C#1 at slave addr 0x20
++ fragment@51 {
++ target = <&sx1502_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1502 on I2C#0 at slave addr 0x21
++ fragment@52 {
++ target = <&sx1502_0_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1502 on I2C#1 at slave addr 0x21
++ fragment@53 {
++ target = <&sx1502_1_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1503 on I2C#0 at slave addr 0x20
++ fragment@54 {
++ target = <&sx1503_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1503 on I2C#1 at slave addr 0x20
++ fragment@55 {
++ target = <&sx1503_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1504 on I2C#0 at slave addr 0x20
++ fragment@56 {
++ target = <&sx1504_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1504 on I2C#1 at slave addr 0x20
++ fragment@57 {
++ target = <&sx1504_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1504 on I2C#0 at slave addr 0x21
++ fragment@58 {
++ target = <&sx1504_0_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1504 on I2C#1 at slave addr 0x21
++ fragment@59 {
++ target = <&sx1504_1_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1505 on I2C#0 at slave addr 0x20
++ fragment@60 {
++ target = <&sx1505_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1505 on I2C#1 at slave addr 0x20
++ fragment@61 {
++ target = <&sx1505_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1505 on I2C#0 at slave addr 0x21
++ fragment@62 {
++ target = <&sx1505_0_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1505 on I2C#1 at slave addr 0x21
++ fragment@63 {
++ target = <&sx1505_1_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1506 on I2C#0 at slave addr 0x20
++ fragment@64 {
++ target = <&sx1506_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1506 on I2C#1 at slave addr 0x20
++ fragment@65 {
++ target = <&sx1506_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3E
++ fragment@66 {
++ target = <&sx1507_0_3E>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_3E_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3E
++ fragment@67 {
++ target = <&sx1507_1_3E>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_3E_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3F
++ fragment@68 {
++ target = <&sx1507_0_3F>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_3F_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3F
++ fragment@69 {
++ target = <&sx1507_1_3F>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_3F_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x70
++ fragment@70 {
++ target = <&sx1507_0_70>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_70_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x70
++ fragment@71 {
++ target = <&sx1507_1_70>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_70_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x71
++ fragment@72 {
++ target = <&sx1507_0_71>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_71_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x71
++ fragment@73 {
++ target = <&sx1507_1_71>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_71_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x20
++ fragment@74 {
++ target = <&sx1508_0_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x20
++ fragment@75 {
++ target = <&sx1508_1_20>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_20_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x21
++ fragment@76 {
++ target = <&sx1508_0_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x21
++ fragment@77 {
++ target = <&sx1508_1_21>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_21_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x22
++ fragment@78 {
++ target = <&sx1508_0_22>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_22_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x22
++ fragment@79 {
++ target = <&sx1508_1_22>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_22_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x23
++ fragment@80 {
++ target = <&sx1508_0_23>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_23_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x23
++ fragment@81 {
++ target = <&sx1508_1_23>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_23_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3E
++ fragment@82 {
++ target = <&sx1509_0_3E>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_3E_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3E
++ fragment@83 {
++ target = <&sx1509_1_3E>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_3E_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3F
++ fragment@84 {
++ target = <&sx1509_0_3F>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_3F_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3F
++ fragment@85 {
++ target = <&sx1509_1_3F>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_3F_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x70
++ fragment@86 {
++ target = <&sx1509_0_70>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_70_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x70
++ fragment@87 {
++ target = <&sx1509_1_70>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_70_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x71
++ fragment@88 {
++ target = <&sx1509_0_71>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_0_71_pins>;
++ };
++ };
++
++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x71
++ fragment@89 {
++ target = <&sx1509_1_71>;
++ __dormant__ {
++ interrupt-parent = <&gpio>;
++ interrupt-controller;
++ pinctrl-names = "default";
++ pinctrl-0 = <&sx150x_1_71_pins>;
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x20
++ // Configure as a input with no pull-up/down
++ fragment@90 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_20_pins: sx150x_0_20_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-20-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x20
++ // Configure as a input with no pull-up/down
++ fragment@91 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_20_pins: sx150x_1_20_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-20-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x21
++ // Configure as a input with no pull-up/down
++ fragment@92 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_21_pins: sx150x_0_21_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-21-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x21
++ // Configure as a input with no pull-up/down
++ fragment@93 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_21_pins: sx150x_1_21_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-21-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x22
++ // Configure as a input with no pull-up/down
++ fragment@94 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_22_pins: sx150x_0_22_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-22-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x22
++ // Configure as a input with no pull-up/down
++ fragment@95 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_22_pins: sx150x_1_22_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-22-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x23
++ // Configure as a input with no pull-up/down
++ fragment@96 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_23_pins: sx150x_0_23_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-23-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x23
++ // Configure as a input with no pull-up/down
++ fragment@97 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_23_pins: sx150x_1_23_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-23-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3E
++ // Configure as a input with no pull-up/down
++ fragment@98 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_3E_pins: sx150x_0_3E_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-3E-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3E
++ // Configure as a input with no pull-up/down
++ fragment@99 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_3E_pins: sx150x_1_3E_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-3E-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3F
++ // Configure as a input with no pull-up/down
++ fragment@100 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_3F_pins: sx150x_0_3F_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-3F-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3F
++ // Configure as a input with no pull-up/down
++ fragment@101 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_3F_pins: sx150x_1_3F_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-3F-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x70
++ // Configure as a input with no pull-up/down
++ fragment@102 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_70_pins: sx150x_0_70_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-70-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x70
++ // Configure as a input with no pull-up/down
++ fragment@103 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_70_pins: sx150x_1_70_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-70-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x71
++ // Configure as a input with no pull-up/down
++ fragment@104 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_0_71_pins: sx150x_0_71_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-0-71-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x71
++ // Configure as a input with no pull-up/down
++ fragment@105 {
++ target = <&gpio>;
++ __dormant__ {
++ sx150x_1_71_pins: sx150x_1_71_pins {
++ brcm,pins = <0>; /* overwritten by sx150x-1-71-int-gpio parameter */
++ brcm,function = <0>;
++ brcm,pull = <0>;
++ };
++ };
++ };
++
++ __overrides__ {
++ sx1501-0-20 = <0>,"+0+2";
++ sx1501-1-20 = <0>,"+1+3";
++ sx1501-0-21 = <0>,"+0+4";
++ sx1501-1-21 = <0>,"+1+5";
++ sx1502-0-20 = <0>,"+0+6";
++ sx1502-1-20 = <0>,"+1+7";
++ sx1502-0-21 = <0>,"+0+8";
++ sx1502-1-21 = <0>,"+1+9";
++ sx1503-0-20 = <0>,"+0+10";
++ sx1503-1-20 = <0>,"+1+11";
++ sx1504-0-20 = <0>,"+0+12";
++ sx1504-1-20 = <0>,"+1+13";
++ sx1504-0-21 = <0>,"+0+14";
++ sx1504-1-21 = <0>,"+1+15";
++ sx1505-0-20 = <0>,"+0+16";
++ sx1505-1-20 = <0>,"+1+17";
++ sx1505-0-21 = <0>,"+0+18";
++ sx1505-1-21 = <0>,"+1+19";
++ sx1506-0-20 = <0>,"+0+20";
++ sx1506-1-20 = <0>,"+1+21";
++ sx1507-0-3E = <0>,"+0+22";
++ sx1507-1-3E = <0>,"+1+23";
++ sx1507-0-3F = <0>,"+0+24";
++ sx1507-1-3F = <0>,"+1+25";
++ sx1507-0-70 = <0>,"+0+26";
++ sx1507-1-70 = <0>,"+1+27";
++ sx1507-0-71 = <0>,"+0+28";
++ sx1507-1-71 = <0>,"+1+29";
++ sx1508-0-20 = <0>,"+0+30";
++ sx1508-1-20 = <0>,"+1+31";
++ sx1508-0-21 = <0>,"+0+32";
++ sx1508-1-21 = <0>,"+1+33";
++ sx1508-0-22 = <0>,"+0+34";
++ sx1508-1-22 = <0>,"+1+35";
++ sx1508-0-23 = <0>,"+0+36";
++ sx1508-1-23 = <0>,"+1+37";
++ sx1509-0-3E = <0>,"+0+38";
++ sx1509-1-3E = <0>,"+1+39";
++ sx1509-0-3F = <0>,"+0+40";
++ sx1509-1-3F = <0>,"+1+41";
++ sx1509-0-70 = <0>,"+0+42";
++ sx1509-1-70 = <0>,"+1+43";
++ sx1509-0-71 = <0>,"+0+44";
++ sx1509-1-71 = <0>,"+1+45";
++ sx1501-0-20-int-gpio = <0>,"+46+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1501_0_20>,"interrupts:0";
++ sx1501-1-20-int-gpio = <0>,"+47+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1501_1_20>,"interrupts:0";
++ sx1501-0-21-int-gpio = <0>,"+48+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1501_0_21>,"interrupts:0";
++ sx1501-1-21-int-gpio = <0>,"+49+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1501_1_21>,"interrupts:0";
++ sx1502-0-20-int-gpio = <0>,"+50+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1502_0_20>,"interrupts:0";
++ sx1502-1-20-int-gpio = <0>,"+51+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1502_1_20>,"interrupts:0";
++ sx1502-0-21-int-gpio = <0>,"+52+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1502_0_21>,"interrupts:0";
++ sx1502-1-21-int-gpio = <0>,"+53+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1502_1_21>,"interrupts:0";
++ sx1503-0-20-int-gpio = <0>,"+54+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1503_0_20>,"interrupts:0";
++ sx1503-1-20-int-gpio = <0>,"+55+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1503_1_20>,"interrupts:0";
++ sx1504-0-20-int-gpio = <0>,"+56+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1504_0_20>,"interrupts:0";
++ sx1504-1-20-int-gpio = <0>,"+57+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1504_1_20>,"interrupts:0";
++ sx1504-0-21-int-gpio = <0>,"+58+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1504_0_21>,"interrupts:0";
++ sx1504-1-21-int-gpio = <0>,"+59+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1504_1_21>,"interrupts:0";
++ sx1505-0-20-int-gpio = <0>,"+60+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1505_0_20>,"interrupts:0";
++ sx1505-1-20-int-gpio = <0>,"+61+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1505_1_20>,"interrupts:0";
++ sx1505-0-21-int-gpio = <0>,"+62+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1505_0_21>,"interrupts:0";
++ sx1505-1-21-int-gpio = <0>,"+63+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1505_1_21>,"interrupts:0";
++ sx1506-0-20-int-gpio = <0>,"+64+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1506_0_20>,"interrupts:0";
++ sx1506-1-20-int-gpio = <0>,"+65+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1506_1_20>,"interrupts:0";
++ sx1507-0-3E-int-gpio = <0>,"+66+98", <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1507_0_3E>,"interrupts:0";
++ sx1507-1-3E-int-gpio = <0>,"+67+99", <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1507_1_3E>,"interrupts:0";
++ sx1507-0-3F-int-gpio = <0>,"+68+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1507_0_3F>,"interrupts:0";
++ sx1507-1-3F-int-gpio = <0>,"+69+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1507_1_3F>,"interrupts:0";
++ sx1507-0-70-int-gpio = <0>,"+60+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1507_0_70>,"interrupts:0";
++ sx1507-1-70-int-gpio = <0>,"+71+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1507_1_70>,"interrupts:0";
++ sx1507-0-71-int-gpio = <0>,"+72+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1507_0_71>,"interrupts:0";
++ sx1507-1-71-int-gpio = <0>,"+73+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1507_1_71>,"interrupts:0";
++ sx1508-0-20-int-gpio = <0>,"+74+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1508_0_20>,"interrupts:0";
++ sx1508-1-20-int-gpio = <0>,"+75+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1508_1_20>,"interrupts:0";
++ sx1508-0-21-int-gpio = <0>,"+76+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1508_0_21>,"interrupts:0";
++ sx1508-1-21-int-gpio = <0>,"+77+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1508_1_21>,"interrupts:0";
++ sx1508-0-22-int-gpio = <0>,"+78+94", <&sx150x_0_22_pins>,"brcm,pins:0", <&sx1508_0_22>,"interrupts:0";
++ sx1508-1-22-int-gpio = <0>,"+79+95", <&sx150x_1_22_pins>,"brcm,pins:0", <&sx1508_1_22>,"interrupts:0";
++ sx1508-0-23-int-gpio = <0>,"+80+96", <&sx150x_0_23_pins>,"brcm,pins:0", <&sx1508_0_23>,"interrupts:0";
++ sx1508-1-23-int-gpio = <0>,"+81+97", <&sx150x_1_23_pins>,"brcm,pins:0", <&sx1508_1_23>,"interrupts:0";
++ sx1509-0-3E-int-gpio = <0>,"+82+98", <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1509_0_3E>,"interrupts:0";
++ sx1509-1-3E-int-gpio = <0>,"+83+99", <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1509_1_3E>,"interrupts:0";
++ sx1509-0-3F-int-gpio = <0>,"+84+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1509_0_3F>,"interrupts:0";
++ sx1509-1-3F-int-gpio = <0>,"+85+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1509_1_3F>,"interrupts:0";
++ sx1509-0-70-int-gpio = <0>,"+86+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1509_0_70>,"interrupts:0";
++ sx1509-1-70-int-gpio = <0>,"+87+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1509_1_70>,"interrupts:0";
++ sx1509-0-71-int-gpio = <0>,"+88+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1509_0_71>,"interrupts:0";
++ sx1509-1-71-int-gpio = <0>,"+89+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1509_1_71>,"interrupts:0";
++ };
++};
++